Pneumatic Riveter #505921, JAT-920 Operation & Parts Manual M-505921 Edition 1 11/2018 JET 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.
Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. JET products carry a limited warranty which varies in duration based upon the product.
Safety warnings General air tool warnings 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand all warnings posted on the tool and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace warning labels if they become obscured or removed. 4. Do not use this tool for other than its intended use.
25. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 26. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 27. Repetitive motions and/or exposure to constant vibration can be harmful to hands and arms. Take frequent breaks and relax hands during extended operation. Change posture to avoid discomfort or fatigue. 28.
About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JAT-920 Pneumatic Riveter. This manual contains instructions on safety precautions, general operating procedures, maintenance procedures and parts breakdown. Your tool has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this document.
Setup and Assembly 2. Use wrench to unscrew nosepiece counterclockwise. See Figure 2. Any missing parts or damage should be reported immediately to your JET® distributor. Do not use a damaged tool. Read this instruction manual thoroughly for operation, maintenance and safety instructions. Box contents: 1 1 2 4 1 1 Pneumatic riveter Safety cap with knurled ring Wrenches Nosepieces (3/16, 5/32, 1/8, 3/32)* Operation and parts manual Warranty card * a nosepiece may come preinstalled on riveter.
Maintenance Lubrication The air riveter should be lubricated daily (or before each use) with air tool oil through the air inlet. During continual operation, it should be re-oiled every 1 to 2 hours. This can be done with an inline oiler, or manually. If done manually, proceed as follows: 1. Disconnect air hose from tool. 2. Place 4 or 5 drops of air tool oil into air inlet (Figure 1). Figure 3 NOTE: Air tool oil not provided; it is available at most major hardware and tool stores.
6. Air-line pressure may be increased accordingly to compensate for extra-long air hoses (usually over 25 feet). Inside diameter of hose should be minimum 3/8-inch. General Air Tool Information If the air tool is not performing according to specifications, the following are among the most common causes. (See also “Troubleshooting” section.) Contaminated air such as a dirty air system or water in the system. Using wrong size tool for the job.
Figure 3 Recommended arrangement of air piping and air line system JET 9
Troubleshooting JAT-920 Pneumatic Riveter Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Riveting force insufficient. Air valve obstructed. Clear any obstructions. Low air pressure. Verify compressor has proper CFM rating for tool. Check compressor regulator setting; set air pressure to 90 psi. Check for loose connections. Dirt or gum deposits on components.
Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately.
#505921, JAT-920 Pneumatic Riveter – exploded view 12 JAT-920 Pneumatic Riveter
#505921, JAT-920 Pneumatic Riveter – parts list Index Part No. 1 706-1A 706-1B 706-1C 706-1D 6-1 JAT920-021B 6-2 JAT920-022B 7 JAT920-7B 8 JAT920-8B 9 706-07A 10 JAT920-10B 10A 706-17 11 706-06 12 706-07 13 708-08 14 706-09 15 JAT920-15B 16 JAT920-16B 17 706-12 18 JAT920-18B 19 JAT920-19B 20 706-15 21 706-16 22 706-16A 23 706-18 24 JAT920-24B 25 706-21 26 706-20 27 706-22 Description Nosepiece 3/16 in. Nosepiece 5/32 in. Nosepiece 1/8 in. Nosepiece 3/32 in.
This page intentionally left blank.
This page intentionally left blank.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
