Operating Instructions and Parts Manual JBM-5 Benchtop Mortiser WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com Part No. M-708580 Revision G2 09/2010 Copyright © 2010 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET ® tools.
Table of Contents Warranty and Service..........................................................................................................................2 Table of Contents ...............................................................................................................................3 Introduction ........................................................................................................................................3 Warning ............................................
Warning • • • • • • • • • • • • • • • • • • • • • • KEEP GUARDS IN PLACE and in order. REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. KEEP THE WORK AREA CLEAN. Cluttered areas and benches invite accidents. DO NOT USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. KEEP CHILDREN AWAY.
Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided.
Specifications Stock Number .......................................................................................................................... 708580 Model Number ............................................................................................................................ JBM-5 Motor ................................................................................................... TEFC, 1/2HP, 1PH, 115V, 60Hz RPM .......................................................................
Assembly Never connect the machine to the power source until assembly is completed. Failure to comply may result in serious injury! 1. Screw the handle (A, Fig. 2) into the pinion shaft (B, Fig. 2). 2. Tighten the handle. The handle has a notch (C, Fig. 2) to accommodate a wrench. 3. Use the handle to raise the machine head to the up position. The handle is spring loaded and can be repositioned by pulling the handle away from the machine, and turned to the desired angle. 4.
Adjustments On-Off Switch The switch (A, Fig. 5) has a switch key that, when pulled out, allows the switch to be locked in the off position. Handle Adjustment The handle can be adjusted for leverage and comfort. Pulling the spring loaded handle (A, Fig.6) away from the head and turning allows you to change the position of the handle. Figure 4 Fence Adjustment The fence can be moved in and out by loosening the locking handle (B, Fig.4) on the column. Hold Down Adjustment The hold down (C, Fig.
Using Bits with Short Shanks When using bits with short shanks, it will be necessary to attach the spindle extension. Place an open wrench on the flat part of the motor spindle. Use the chuck key to unscrew and remove the chuck. Attach the spindle extension to the chuck. Replace the chuck with the spindle extension into the motor spindle. Chisel and Bit Adjustment See Figure 7. Figure 7 Insert chisel bushing with hole facing forward into the head. Tighten the screw just enough to hold the chisel in place.
JBM-5 Benchtop Mortiser 10
Parts List for JBM-5 Benchtop Mortiser To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Index No. Part No. Description Size Qty 1 .............. 23011045W .............Base ..................................................................................................
49 ............ 23011068 ................Spring ................................................................................................ 2 50 ............ 23011050 ................Switch Base ....................................................................................... 1 51 ............ 23011051 ................Switch Cover ...................................................................................... 1 52 ............ 23011029 ................Toggle Switch.........................
