This .pdf document is bookmarked Operating Instructions and Parts Manual Benchtop Oscillating Spindle Sander Model JBOS-5 For models with serial no. 11095097 and higher JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
Warranty and Service JET, Wilton and Powermatic warrants every product they sell against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET, Wilton or Powermatic branded websites.
Table of Contents Warranty and Service ............................................................................................................................................ 2 Table of Contents .................................................................................................................................................. 3 Warning ...........................................................................................................................................................
Warning 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this tool until proper training and knowledge have been obtained. 2. Keep guards in place and in working order. 3. Keep fingers and hands away from the spindle while in operation. Avoid getting fingers too close to the drum. 4. Remove adjusting keys and wrenches. Form habit of checking to see that keys and adjusting wrenches are removed before operating. 5. Keep work area clean.
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for a JET Model JBOS-5 Oscillating Spindle Sander. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual.
Unpacking and Setup Contents of the Shipping Container (see Figure 1) 1 Spindle Sander 1 Spindle Storage Plate (pre-installed) 1 Insert Storage Plate (pre-installed) 2 Round Opening Inserts (3/4” and 2”) 2 Oblong Opening Inserts (3/4” and 2”) 5 Sanding Spindles & Sleeves (all 100 Grit): 1/4”x6”; 1/2”x6”; 5/8”x6”; 1-1/2”x5-1/2”; 2”x5-1/2” 1 Open End Wrench (10-12mm) 2 Open End Wrenches (14-17mm) 1 Operator’s Manual 1 Warranty Card Figure 1 Contents of Shipping Container Finish removing all contents from th
Insert Plates 1. Always use an insert plate. 2. There are 2 oblong, and 2 round insert plates included with the machine. The oblong insert plates are used when the table is tilted for bevel sanding. Each plate has a notch on the outer edge to ensure that it is inserted properly. (See page 9 to determine which insert plate to use with a particular spindle.) Setup for 90° 1. Loosen both knobs, (A, Figure 4) and place the table in the 0° position. 2. Place a square (B, Figure 4) on the table.
Turning the Sander On & Off Note: Before hooking the sander to the power source, make sure the switch is in off position. The sander can be turned on by flipping the switch to the on position. There is a removable key in the tip of the switch that can be removed in the off position. When the key has been removed the dust collector cannot be used.
Insert Plate Diameters This will assist you in determining which spindle diameters will work in each insert plate.
Optional Accessories (purchased separately) 709534 ...... 3” Dia. Spindle Assembly 6286984 .... Table Insert for 3” Spindle Sanding Sleeves (4 per pack): Stock No. Diameter (in.) Length (in.
Table Assembly for the JBOS-5 11
Base and Motor Assembly for the JBOS-5 12
Parts List for the JBOS-5 Index No. Part No. Description Size Qty 1 ................ 6286914W ................. Base......................................................................... ...................................... 1 2 ................ 6286891 .................... Top Plate ................................................................. ...................................... 1 3 ................ JBOS5-03.................. On/Off Switch.....................................................
Index No. Part No. Description Size Qty 62 .............. 6286894 .................... Main Spindle serial #2014090 & lower .................... ...................................... 1 .................. 6286894N.................. Main Spindle serial #2024091 & higher ................... ...................................... 1 62-1 ........... S0520020 .................. C-Ring...................................................................... ...................................... 1 63 ...........
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
