This Manual is Bookmarked JET WMH TOOLGROUP TOOL Operating Instructions and Parts Manual 17" Drill Press Model JDP-17MF WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Ph.: 800-274-6848 www.wmhtoolgroup.com Part No.
Thismanualhasbeenpreparedfor the ownerandoperatorsof a JDP-17MFDrill Press. Its purpose, asidefrommachineoperation,is to promotesafetythroughthe useof acceptedcorrectoperatingand maintenance procedures.Completely readthe safetyandmaintenance instructions beforeoperatingor servicingthe machine.Toobtainmaximumlife andefficiencyfromyourJETDrillPress,andto aidin usingthemachinesafely,readthismanualthoroughly andfollowinstructions carefully.
, WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. Support workpiece adequately at all times during operation; maintain control of work at all times.
• USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. NEVER STAND ON A MACHINE. Serious injury could occur if the machine is tipped. CHECK DAMAGED PARTS.
Grounding Caution: Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
230Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: . 2. Disconnect the machine from the power source. This JET drill press is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. . The 115V attachment plug (A), supplied with the drill press, must be replaced with a UL/CSA listed plug suitable for 230V operation (D).
On-Off Switch Padlock Model No. BP-1, Stock No. 709736 To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock is highly recommended. JET model BP-1 is available from your local authorized JET distributor or by calling WMH Tool Group at 800-274-6848. Figuri_ \ \ Figure To lock out an on-off switch: 1. Open the padlock. See Fig. A. 2. Insert through holes in the start button. See Fig. B 3. Close the padlock. 4.
Specifications: JDP-17MF Stock Number ..................................................................................................................................... 354169 Swing .................................................................................................................................................... 16-1/2" Type ........................................................................................................................................................
Contents 1 1 1 1 1 1 1 3. 1. 1. 4. 1. 1. of the Shipping Head Assembly Table Column and Bracket Assembly Base Owner's Manual Warranty Registration Card Chuck and Chuck Key Downfeed Handle Table Bracket Lock Handle Table Bracket Raising Handle M10 x40 Hex Cap Bolts Arbor Drift Key Tools Supplied 1. 1. for Assembly 3mm HexWrench 5mm HexWrench Tools Required 1.
Assembly 1. . 3. Place the base (A, Fig. 1) on a level floor. With a 17mm wrench attach the column assembly (B, Fig. 1) to the base (A, Fig. 1) with four M10 x 40 hex cap bolts (C, Fig. 1). Tighten firmly. Thread lock handle (D, Fig. 2) into the table bracket (E, Fig. 2). 4. Loosen the set screw (F, Fig. 3) on the raising handle (G, Fig. 3) with a 3mm hex wrench. 5. Slide the shaft. handle onto the table Fig. 1 bracket Fig, 2 . . 8.
9. Withtheaidofa secondperson,carefullylift the headonto the columntop. Caution: The headassemblyis heavy! Usecare whenliftingonto the column! 10. Rotateheadassemblyuntilsidesofthe belt coverareparallelwiththesidesofthebase. 11.Tightentwo set screws(A, Fig.4) with a 5mmwrenchuntiltheyaresnug. belowthechuck. . . . Place a piece of scrap wood on the table, and lower quill using the down feed handle. Rotate spindle to align the key hole in the spindle with the key hole in the quill.
Adjusting the Depth Stop To drill multiple holes at the same preset depth, use the depth stop: 1. Use a pencil to mark the depth the bit will drill into the workpiece (A, Fig. 7). 2. With the drill bit in the chuck, lower down feed handle to advance bit to your mark,see Figure 7. 3. With your other hand, advance the lock nuts (B, Fig. 7) on the depth stop rod until they are snug to the seat (C, Fig. 7). 4. The drill bit will now advance to this point. 5.
SPINDLE SPEEDS IN R.P.M.
Return Spring Adjustment The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary: 1. Unplug source. 2. Loosen two jam nuts (A, Fig. 9). remove. 3. Firmly hold the coil spring cover (B, Fig. 9). . . the machine from the power Do not Pull out the cover and rotate until the pin (C, Fig. 9) on the return spring plate engages the next notch in the coil spring cover.
Basic Operation • Always use a back-up piece of scrap wood to cover the table. This protects both the table and the drill bit. Place material to be drilled in such as way as to come into contact with the left side of the column. This prevents the material from spinning.
Troubleshooting Trouble Drill press will not start. Drill press does not come up to speed. Drill Press vibrates excessively. Probable Cause 1. Drill press unplugged from wall, or motor. 2. 3. Fuse blown, or circuit breaker tripped. Cord damaged. 4. Starting capacitor bad. 1. Extension cord too light or too long. Low current. 2. Remedy 1. Check all plug connections. 2. Replace fuse, or reset circuit breaker. 3. 4. Replace cord. Replace starting capacitor. 1.
Parts Breakdown for JDP-17MF 119 99 8 801 79 35 76 75 74 52 49A tO II 17
Parts List for JET JDP-17MF Index No. Part No. 1 .......... 10600111 ...................... 2A ........ 12909001A1 .................. 3 .......... TS-1525021 .................. 5 .......... TS-1491061 .................. 6 .......... 10700605A1 .................. 7 .......... 10600702 ...................... 8 .......... 10600802 ...................... 9 .......... 10600902 ...................... 10 ........ 10601002 ...................... 11 ........ TS-1523031 .................. 12 ........ 10901203A1 ...
Index Part No. No. Description Size Qty. 61 ........ BB-6203Z ...................... Ball Bearing .............................................................................................. 62 ........ 10606201 ...................... Washer ..................................................................................................... 63 ........ 10606301 ...................... Lock Nut ...................................................................................................
Index Part No. No. Description Size Qty. 169 601 602 607 ...... 11316904 ...................... ...... TS-1533032 .................. ...... 2504MZC005 ................ ...... TS-0720101 .................. Nameplate ................................................................................................ Pan Head Machine Screw ................................... M5xlO ......................... Tooth Washer .......................................................................................
Wiring Diagram JDP-17MF ELECTRICAL .BLACK SCHEMATIC - 115V _C.K 2 O.,OF_SW,TC.
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.
