Product Manual
Table Of Contents
- Variable Speed Mill-Drill Machines
- 1.0 IMPORTANT SAFETY INSTRUCTIONS
- 2.0 Table of contents
- 3.0 About this manual
- 4.0 Specifications
- 5.0 Setup and assembly
- 6.0 Electrical connections
- 7.0 Adjustments
- 8.0 Operation
- 9.0 User-maintenance
- 10.0 Troubleshooting JMD-45VS series Mill-Drills
- 11.0 Optional accessory
- 12.0 Replacement Parts
- 12.1.1 JMD-45VSPF, -45VSPFT Table and Base Assembly – Exploded View
- 12.1.2 JMD-45VSPF, -45VSPFT Table and Base Assembly – Parts List
- 12.2.1 JMD-45VSPF, -45VSPFT Column Assembly – Exploded View
- 12.2.2 JMD-45VSPF, -45VSPFT Column Assembly – Parts List
- 12.3.1 JMD-45VSPF, -45VSPFT Gear Head Assembly – Exploded View
- 12.3.2 JMD-45VSPF, -45VSPFT Gear Head Assembly – Parts List
- 12.4.1 JMD-45VSPFT Tapping Assembly – Exploded View
- 12.4.2 JMD-45VSPFT Tapping Assembly – Parts List
- 12.5.1 JMD-45VSPF, -45VSPFT Gears Assembly – Exploded View
- 12.5.2 JMD-45VSPF, -45VSPFT Gears Assembly – Exploded View
- 12.6.1 JMD-45VSPF Electric Box Assembly – Exploded View
- 12.6.2 JMD-45VSPF Electric Box Assembly – Parts List
- 12.7.1 JMD-45VSPFT Electric Box Assembly – Exploded View
- 12.7.2 JMD-45VSPFT Electric Box Assembly – Parts List
- 13.0 Electrical Connections, JMD-45VSPF series
- 14.0 Warranty and service
3
26. Maintain tools with care. Keep cutters sharp
and clean for the best and safest performance.
Follow instructions for lubricating and changing
accessories.
27. Turn off the machine before cleaning. Use a
brush or compressed air to remove chips or
debris — do not use bare hands.
28. Do not stand on the machine. Serious injury
could occur if the machine tips over.
29. Never leave the machine running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
30. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
31. Do not perform any setup work while machine
is operating.
32. Do not place hands near cutter while machine
is operating.
33. Don’t use in dangerous environment. Don’t use
power tools in damp or wet location, or expose
them to rain. Keep work area well lighted.
34. All work shall be secured using either clamps or
a vise to the drill press table. It is unsafe to use
your hands to hold any workpiece being drilled.
35. Use proper extension cord. Make sure your
extension cord is in good condition. When using
an extension cord, use one heavy enough to
carry the current your product will draw. An
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Sect.
6.3, Table 2 shows correct size to use
depending upon cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the
heavier the cord.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious, or possibly even fatal,
injury.
1.1 Switch lock-out
To prevent unauthorized use or accidental starting of the Mill-Drill, install a padlock (not provided) into the on/off
switch at rear of control box. Push tab into switch until holes align and insert padlock through holes. See Figure
1-1. Store key in a secure place.
Figure 1-1