Operating Instructions and Parts Manual SLT-660F/1650 Scissor Lift Tables WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com Part No. M-140777 Revision C 11/2010 Copyright © 2010 Walter Meier (Manufacturing) Inc.
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET ® tools.
Table of Contents Warranty and Service..........................................................................................................................2 Table of Contents ...............................................................................................................................3 Specifications .....................................................................................................................................3 Assembly ............................................
Assembly Note: The SLT-660F does not require any assembly. 1. On the SLT-1650, attach the handle (A, Figure 1) to the frame using two hex cap screws, two lock washers, two flat washers. Tighten with a 19mm wrench. Note: The two pivoting casters can be locked so that they do not rotate. Press foot lever (B, Figure 1 for SLT-1650) down to lock. Press foot lever (A, Figure 2 for SLT660F) down to lock. 2.
Operation Maintenance 1. The table can be raised by pumping the foot lever. 1. Lubricate each friction point monthly with #2 tube grease. Note: You may need to raise and lower the table several times to work any air bubbles out of the pump. 2. Check the movement and wear of wheels. 3. Check for oil leakage from the hydraulic cylinder. Add hydraulic oil as needed. 2. To lower the table, pull the release lever fully. This allows the table to lower in a slow, controllable manner. 4.
Troubleshooting The numbers in parentheses refer to the appropriate breakdown; 660F listed first/1650 listed second. Trouble Probable Cause Remedy Oil level low in reservoir. Replenish reservoir. Lowering valve (28/29) or steel ball (25/26) is not seating. Clean lowering valve (28/29) or steel ball (25/26) or replace. Steel ball (13/14) is not seating. Clean or replace steel ball (13/14). Relief valve is not adjusted properly.
Parts Breakdown for SLT-660F Scissor Lift Table 7
Parts List for SLT-660F Scissor Lift Table Index No. Part No. Description Size Qty 1 .............. SLC660F-01 ............Table ................................................................................................. 1 2 .............. SLT660F-06 ............Link Shaft ........................................................................................... 2 3 .............. SLC660F-02 ............Link Assembly ................................................................................
Index No. Part No. Description Size Qty [18] .......... SLT660F-36-13 .......Spring ................................................................................................ 1 [19] .......... SLT660F-36-14 .......Steel Ball Support ............................................................................... 1 [20] .......... SB-5MM ..................Steel Ball..........................................................Ø 5 mm...................... 1 [21] .......... SLT660F-36-21 .......Screw ....
Index No. Part No. Description Size Qty 69 ............ SLC660F-47 ............Foot Lever Pad ................................................................................... 1 70 ............ SLT660FH-70 ..........Hex Cap Screw ................................................M10 x 30 .................... 1 71 ............ SLT660FH-71 ..........Safety Bar .......................................................................................... 1 72 ............ SLT660FH-72 ..........Hex Nut.........
Parts Breakdown for SLT-1650 Scissor Lift Table 11
Parts List for SLT-1650 Scissor Lift Table Index No. Part No. Description Size Qty 1 .............. SLC1650-1 ..............Table ................................................................................................. 1 2 .............. SLC660F-38 ............C-Ring .............................................................Ø 20 mm .................... 2 3 .............. SLC1650-2 ..............Link Assembly ....................................................................................
Index No. Part No. Description Size Qty [17] ......... SLT660F-36-11 .......Relief Adjusting Screw ........................................................................ 1 [18] .......... SLT660F-36-9 .........O-Ring* ............................................................Ø 11 x 1.9 mm............ 2 [19] .......... SLT660F-36-13 .......Spring ................................................................................................ 1 [20] .......... SLT660F-36-14 .......Steel Ball Support .
Index No. Part No. Description Size Qty 66 ............ SLC660F-45A..........Rubber Bumper .................................................................................. 1 67 ............ SLT660FH-22 ..........Spring Washer..................................................Ø 8 mm...................... 1 68 ............ SLT660FH-67 ..........Hex Cap Screw ................................................M8 x 30 ...................... 1 69 ............ SLT1650H-69 ..........Foot Lever...................
WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com www.waltermeier.
