EN computer radio control system extended serie Receivers 1 Introduction ENGLISH FW. ver. 3.10 Jeti DUPLEX Receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2,4 GHz frequency band. DUPLEX receivers are offered in a wide range of size and features to suit the numerous demands of our customers. The DUPLEX receivers range from the tiny DUPLEX R4-R7 receivers for small and medium model sizes to the R8-R12 receivers for larger models.
computer radio control system EN The legacy DUPLEX system was designed to give maximum dependability, a property which has proven itself through many successful years of use. Based on user input, the system is continuously improved. Thanks to online updates the improvements are easily accessible to users from any part of the world.
EN computer radio control system 2 Technical data 2.1 Technical data receivers outside the U.S.
EN computer radio control system 2.1 Technical data receivers outside the U.S.
EN computer radio control system 2.2 Technical data receivers for the U.S. part 1 Basic Data R4L R5L R6L (R4L indoor) (R5L indoor) (R6L indoor) R7plus Dimensions [mm] 38x20x7 47x20x7 43x24x11 51x24x11 Weight [g] 4,8 (4,5) 5,4 (5) 13 13 Antenna Length [mm] 2x100 (2x45) 2x100 (2x45) 2x200 (2x50) 2x200 5 5 6 7 -10 to +85 -10 to +85 -10 to +85 -10 to +85 3.2 – 8.4 3.2 – 8.4 3.2 – 8.4 3.2 – 8.
EN computer radio control system 2.2 Technical data receivers for the U.S. part 2 R9 R11 EPC* R14* R18* 51x24x11 51x24x11 62x38x16 62x38x16 13 15 30 30 Antenna Length [mm] 2x200 2x200 2x400 2x400 # of Channel Outputs 9 11 14 18 -10 to +85 -10 to +85 -10 to +85 -10 to +85 3.2 – 8.4 3.2 – 8.4 3.2 – 8.4 3.2 – 8.
computer radio control system EN 3 Overview 3.1 Voltage Supply When designing the on-board wiring for you project always pay attention to the voltageinput range of your receivers and servos. You can supply voltage to DUPLEX receivers as follows: - Directly from the batteries - Via a BEC voltage regulator (either contained in speed controllers or self contained) The supply may be connected to DUPLEX receivers via: - the throttle channel (when applying speed controllers with BEC) - a free receiver output.
computer radio control system EN 3.3 Binding When using a new receiver or transmitter it is necessary to carry out the binding process between them . Transmission between the receiver and transmitter occurs in fully digital manner, therefore it is necessary to identify and share the addresses of each device communicating on the mutual 2.4GHz frequency band. Procedure: 1. Insert the BIND PLUG (included in the receiver packing) into the receiver socket labeled EXT. 2.
computer radio control system EN seconds elapse the receiver returns to setup mode and the binding process must be repeated by starting again from step 3. If the bind proces between receiver and transmitter was unsuccessful, try again. You may bind an arbitrary number of receivers to one transmitter. The receiver, however, can only be bound to one transmitter, i. e. the receiver is only bound to the most recently bound transmitter. Attention, change after FW version update 3.
computer radio control system EN 4 Real Time Telemetry Every receiver is able to transmit the actual voltage supplied to the on-board system (i. e. receiver voltage) without the need to connect any additional external sensors. If you want to take advantage of extended telemetry, connect a telemetry sensor to the EXT input of the receiver.
computer radio control system EN 5 Receiver setup 5.1 Receiver Setup via the JETIBOX There are two receiver setup modes. The first is receiver setup via the JETIBOX, JETIBOX Profi or JETIBOX emulation in the DC/DS transmitters, the second is one is direct setup of the receiver with a DC/DS transmitter. 5.1.1 Direct connection between a JETIBOX and the Receiver.
computer radio control system EN mode (see point 4.1.1). Wireless connection is only possible when a receiver is in“Normal“ mode (MeasureOrSetting->Main Setting >Rx mode: Normal). The JETIBOX can be disconnected only after you disconnect the receiver voltage supply. You may monitor the on board state of your receiver during your model‘s operation. Pay particular attention, of course, to your setup work. While it is possible, we do not recommend changing setup parameters during model operation.
computer radio control system EN 6 Receiver Menu 6.1 Overview of Receiver Data Items The introductory display shows the type of receiver. By pushing of key R (arrow down) more detailed data of receiver and transmitter can be cued. Pairing- by pushing the key U (arrow up) pairing of the receiver with the transmitter will be executed. Pairing of the receiver should only be carried out when the JETIBOX is directly connected to the receiver. RX/TX- Item RX shows the unic production number of the receiver.
computer radio control system EN 6.2 Measure Measure: enables read out of measured data of the maximum, minimum and actual receiver voltage. Volt Min / Act / Max- the receiver is checking the supply voltage and indicates limit values and extremes which occurred during operation; at the same time it also shows the actual receiver voltage. Without switching on the paired transmitter the values MAX and MIN will not change, only the value of the actual voltage ACT will be updated.
computer radio control system EN voltage, the second value represents the setup threshold level for alarm purposes. During operation, as soon as the actual voltage becomes lower than the threshold level, the transmitter emits an acoustical warning tone. This setup is for transmitter modules only. For DC/DS transmitters, this alarm is set in the transmitter. Output Period: output signal period setup (initial setup for the Autosynchronizing mode with the transmitter).
computer radio control system EN output assignments) will be disabled (there will be no servo signal generated at the remaining outputs). The receiver may be set-up in such a way, that its output will work in digital communication form, which will be used as input by other equipment. EX bus* - in this setup information about servo throws will be generated in EX protocol format.
computer radio control system EN transmitter. Select this setup for the model‘s main receiver. Use the same setup if you use only one receiver in your model (if you are using only one DUPLEX receiver for remote control). Clone - unidirectional communication. If you are using several DUPLEX receivers in the model, for instance, in connection with one redundant transmitter module then you should operate one of the receivers in „Normal“ mode and the others in „clone“ mode.
computer radio control system the JETIBOX, see the „Receiver setup“ chapter. EN If you switch the receiver to „clone“ or „Telemetry“ modes, further wireless setup communication becomes impossible, because the receiver is now communicating only unidirectionally. In order to change the mode or setup you have to connect the JETIBOX to the receiver and make the desired change or switch the receiver to back to„Normal“ mode: 1. Insert BIND PLUG into the receiver socket labeled EXT. 2. Switch-on receiver 3.
computer radio control system EN labelled CH xx. - PPM off: for the given output there is no PPM signal generated or received - PPM input: for the given input there a PPM signal is expected from the connected receiver - PPM output: the receiver channel will generate a PPM signal PPM error code- in the case that one of the SAT1/2 outputs is set to PPM input mode, an acoustic signal can be setup to announce when this connected signal is missing.
computer radio control system EN FS position: throw setup of selected FailSafe output position in case of signal loss FS speed: sets how quickly the throws move to the FailSafe positions in case of signal loss Output Group - setup of given output into a selected group of output pulses, which will be simultaneously generated by the receiver.
EN computer radio control system R4, R4C Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 • • • • R5, R5 R6, R6 R6F, R7, R7 R8,R8 indoor EPC R6G indoor EPC • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Y9 R9 R10 R11 EPC R12 EPC R14 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •/° • • • • • • • • • • • •/°/* • • • • • • • • • • • • • • ° ° °/* Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 SAT1 SAT2 PPM * - PPM input, ° - PPM output, • - servo R18 R sat2 • • • • • • • • • • • • • • • • •/
EN computer radio control system Assignment table of US version receiver outputs R4L, R4Li R5L, R5Li R6L, R6Li Y1 Y2 Y3 Y4 Y5 Y6 Y7 • • • • • • • •/* •/* •/* • • • • •/* R7 plus R9 R11 EPC R14 R18 •/* • • • • • • •/* • • • • • • •/* • •/* • • • • • • •/* • • •/° • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •/°/* •/° Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 SAT1 SAT2 * - PPM input, ° - PPM output, • - servo ° °/*
computer radio control system EN 6.5 Auto Set Loads a default receiver configuration from preset modes Factory defaults -factory default receiver setup. 7 Receiver Update Beginning with version DUPLEX EX, receivers can be updated via PC with aid of the JETI USB adapter. You may find a detailed description of the receiver update process in the USB adapter instruction manual.
computer radio control system JETI BOX mini Button right Button down Button up Button left Button for switching input Ext.
computer radio control system EN For receivers we grant a warranty of 24 months from the day of purchase under the assumption that they have been operated in conformity with these instructions at recommended voltages and that they were not damaged mechanically. Warranty and post warranty service is provided by the manufacturer. We wish you sucessful flying with the products of: JETI model s.r.o. Příbor, www.jetimodel.
computer radio control system EN
