EN evo evo ELECTRONIC SPEED CONTROLLER FOR BLDC MOTOR EN User manual QUICK SETUP Complete manual is available on www.jetimodel.
EN evo evo 1 Introduction MEZON EVO is a series of controllers in aluminium case* with efficient cooling, full telemetry and advanced functions. Controller is designed for RC model planes, helicopters and other vehicles. Controller`s setup is intuitive and together with JETI Duplex transmitter very simple. Features: - full EX telemetry (voltage, current, capacity, revolution etc.
EN evo 2.1 MEZON EVO BEC controllers Trottle channel BEC output evo M 80bec Switch BEC Battery Ext. EX Bus BEC output Y1 Pic.1 - standard connection between controller and receiver suitable for JETI Duplex transmitters users - black JR connector is connected into throttle channel output of receiver - red JR connector is connected into receiver output Ext., E1 or E2 If E1 or E2 receiver output is used then user has to manually configure E1 or E2 output to „EX Bus” functionality.
EN evo If you don´t want to use BEC power supply, take out from JR connectors middle pins (red wired) and isolate correctly. Switching BEC technical data average current 15A max. current 30A (1s) max. temperature 100°C listed values are valid with sufficient air flow cooling 2.2 MEZON EVO OPTO controllers evo Battery 85opto MEZON EVO OPTO controllers have input separation by optocoupler and BEC power supply is not available.
EN evo 3 Configuration (setup) MEZON EVO controllers can be configured from JETI Duplex transmitters (described below), Jetibox or USB interface with JETI Studio application for PC (see *CM) There are two configuration possibilities: "Quick setup" - configuration through wizard (described below) "Expert setting" - full access for all controller possibilities (see *CM) Quick setup with predefined parameters for RC model type is normally sufficient for most users.
EN evo Number of cells Auto – automatic detection of the number accu`s cells BEC voltage – set B E C voltage for electronic equipment, range 5 - 8.4V Warning! The Automatic mode only works properly if you connect fully charged batteries to the controller. Warning! Damage risk of connected electronic equipment if incorrect BEC output voltage is configured. 3.2 Configuration procedure for F3A planes Choose model type, content of menus are automatically adapted for chosen model type.
EN evo 3.3 Configuration procedure for helicopters Choose model type, content of menus are automatically adapted for chosen model type. Number of motor poles set the number of motor poles regards motor producer information. Motor KV - set value of motor`s KV regards motor producer information. If both of above-mentioned parameters are unknown see *CM.
EN evo 4 Telemetry M E ZO N E V O controllers integrates full telemetry with selectable recorded data set. All the selected data is saved and available for later analysis. Possible faults which occurred during operation are recorded in "Status" menu. This menu helps with faults solving and diagnoses. See *CM for detail items description. Menu telemetry „Min/Max” consists recorded minimum and maximum values of important parameters during controller operation. *CM - Complete Manual is available on: www.
EN evo 5 Package contents - assembly Warranty and service This product is covered by warranty for 24 months after the day of purchase provided that it has been operated in accordance with these instructions at the specified voltage and is not mechanically damaged. When claiming warranty repairs for the product, always attach a proof of purchase. Warranty and post-warranty service is provided by your dealer or the manufacturer.
EN evo Safety instructions - use quality power connectors designated for appropriate load current - keep power supply within the allowed voltage/cell range - set BEC voltage within servo producer instructions - ensure sufficient air flow cooling - isolate reliably all wires, conductors and connectors - reverse polarity causes damage to controller with loss of warranty - during controller configuration remove propeller or rotor blades - treat model with respect, after connection of power supply motor/mode
EN evo ® Declaration of Conformity in accordance with the regulations of EU Directive EMC 2014/30/EU, RoHS 2011/65/EU and (EU) 2015/863 This declaration of conformity is issued under the sole responsibility of the manufacturer. Producer: JETI model s.r.o.
EN evo JETI model s.r.o. Lomená 1530, 742 58 Příbor Czech Republic - EU www.jetimodel.com info@jetimodel.
