User Guide
JHS PEDAL MANUAL 12
Lucky Cat Delay
With a full second of delay, tap tempo, ratio, modulation, eq, and more, the Lucky Cat
Delay is everything you want and nothing you don’t need. It’s your lucky delay!
Controls
POWER - Uses 9V DC Negative Center. Do not use more than 9V DC. Your warranty will be voided. 75mA
consumption.
TIME
- Controls the time of the repeats. Left is faster/shorter,
Right is slower/longer.
MIX - Controls the mix or volume of the delay signal. Left is less
mix, right is more mix. All the way left is full dry, all the way right
is full wet.
RATIO - Controls the ratio of the tapped in speed. When all the
way to the left on the quarter note, the delay will be exactly what
you tap in. When you turn it to the right it begins to subdivide
the speed of your tap. You can select dotted eighth note, eighth
note, or triplets.
REPEATS - Controls the amount of repeats the delay will have.
Left is less, right is more. The Lucky Cat will do endless repeats
when set all the way to the right. If you change the Time when
the repeats are all the way up, you will hear a digital feedback
noise. This is normal and could even be used for interesting
sounds like you would hear from an analog delay.
INPUT - Jack on the top right side of the pedal.
OUTPUT - Jack on the top left side of the pedal.
TAP OUT JACK - Jack on the right side of the pedal. Allows you
to use an external tap tempo controller.
Jacks
DARK
- Darkens the tone of the repeats. Fully clockwise is stock
mode. Turning the knob counterclockwise rolls off high end on
the repeats only.
MOD TOGGLE - Choose between two modulation settings that
affect the repeats only. The down position (Mod 1) is a light and
subtle modulation. The middle position bypasses modulation.
The up position (Mod 2) is a deep and intense modulation.
DIGITAL/TAPE SWITCH - Lets you choose between clean and clear
digital delay repeats and slightly saturated and compressed tape
delay repeats.
Panther Cub V2
True analog delay with tap tempo, modulation, expression and more! Find that classic warm delay tone you’ve always wanted.
Controls
POWER - Uses 9V DC negative center power. Do not use more than 9V DC. Your warranty will be voided. 67mA consumption.
Time - Controls the delay time up to 1000ms.
volu me - Controls overall gain of dry and wet sounds. As you turn up
the mix the dry signal will decrease and you can use the Volume control
to compensate or boost the overall signal
mix - Controls volume of the delay repeats only.
ratio - Controls the tap subdivision: Quarter, dotted-eighth, eighth, and
triplet note divisions. The setting of the Ratio control applies constantly
whether using tap tempo or when manually adjusting the Time knob.
F.Back -
Controls the amount of delay repeats. The Panther Cub V2 has
an improved feedback for smooth, in
nite repeats or wild oscillation
noises.
eq - Active EQ tilt control. Noon is “
at”. Turning the knob above noon
boosts highs and cuts lows, while turning the knob below noon boosts
lows and cuts highs. Because the Panther Cub V2 is all analog, the
overall tone of the repeats is dark even when set at noon.
Input - 1/4” jack on the top right receives your instrument’s signal.
Output -
1/4” jack on the top left sends the signal out of the pedal to
an amplier or pedal chain.
Ta p/Exp -
1/4” jack on the right side of the pedal. In Expression
Mode, connect any TRS expression pedal to control Time, Ratio, or
Mod Speed. To program, follow the directions below. In Tap Mode
you can set the speed using an external tap tempo pedal. Choose
which one you want by the TAP/EXP switch on the inside of the
pedal.
Jacks
Switches
By pa ss - Left footswitch turns the pedal on and off.
Ta p tempo - Right footswitch taps in the speed of the delay.
mo d on/off - Turns the modulation on or off for the repeats only.
Mod speed +/- - Selects between faster or slower modulation
speeds.
Internal tap/Exp switch -
Switch on the inside of the pedal. let’s
you choose between tap or expression mode for the TAP/EXP jack.
program mode
With the Panther Cub V2 you have the ability to control Time, Ratio, or Mod Speed with a TRS expression pedal. To select which parameter to control,
hold down the Tap Tempo switch until the tempo LED stops blinking. Once it stops blinking, you are in program mode. Select which parameter to
control by either turning the Time or Ratio knob or by switching the Mod Speed switch one time. Once you have done this, tap the Tap Tempo switch
again and you will exit program mode. You will now be able to control the parameter you selected with your expression pedal.
Milkman
A collaborative idea between JHS Pedals and Milkman Sound, the Milkman offers up an echo/slap
delay and and independent boost for creamy country slap back and a full-fat tone booster you’ll never
want to turn off.
POWER - Uses 9V DC Negative Center. Do not use more than 9V DC. Your warranty will be voided. 27mA
consumption.
LEFT SIDE - SLAP BACK DELAY
SLAP - Controls the time of the repeats. Left is faster
and right is slower, up to 240ms.
MIX - Controls the volume of the repeats. Left is lower
volume and right is higher volume.
REPEAT - Controls the amount of repeats. Left is fewer
repeats and right is more repeats.
EQ - Controls the tone of the repeats. Left is darker
repeats and right is brighter repeats.
RIGHT SIDE - BOOST
BOOST - Controls the volume of the boost. Left is lower
volume and right is higher volume.
LEFT FOOTSWITCH - Bypass for the slap delay.
RIGHT FOOTSWITCH - Bypass for the boost.
INPUT - Jack on the right side of the pedal.
OUTPUT - Jack on the left side of the pedal.
controls
MODULATION DELAY
DELAY