User Guide
JHS PEDAL MANUAL 14
REVERB PREAMP
Spring tank
Classic spring-like reverb in a simple package with enough options to satisfy any spring
reverb enthusiast. Blow them away with the Spring Tank!
Controls
POWER - Uses 9V DC Negative Center. Do not use more than 9V DC. Your warranty will be voided. 100mA max consumption.
BOOST - Controls the amount of volume boost when
the pedal is turned on.
HIGHS - Functions as a high pass lter. Turning right is
brighter, left is darker.
DEPTH - Controls the size or space of the reverb. Left is
smaller, right is bigger.
LENGTH - Controls the decay time of the reverb. Left is
shorter, right is longer.
TANK 1 - Controls the main reverb mix. Left is less, right
is more.
TANK 2 - Controls the reverb mix when the Tank 2
switch is engaged.
INPUT - Lower jack on the right side of the pedal.
EFFECTS LOOP - Upper jack on the right side of the
pedal. Insert a TRS splitter cable into this jack and plug
it in to any pedal to add the effect to the wet reverb
effect only.
OUTPUT - Jack on the left side of the pedal.
Jacks
SWITCHES
BYPASS - Turns the pedal on or off.
TANK 2 - Engages the Tank 2 reverb mix knob which
acts as a secondary reverb mix you can use on the y.
Clover
This classic FET preamplier gives you tons of volume and powerful EQ to shape and
boost your tone for an unforgettably lucky sound.
Controls
POWER - Uses 9V DC Negative Center. Do not use more than 9V DC. Your warranty will be voided.
46mA consumption.
VOLU ME - Controls the overall volume of the unit. You can
set the volume at unity gain or use it to boost your signal.
EQ SelectoR Switch - Select three different EQ types: Full
EQ, No Mid, and No EQ.
Bass - Controls the amount of bass in your signal. Left is
less, right is more
Mi ds - Controls the amount of mid frequencies in your
signal. Left is less, right is more.
Treb le - Controls the amount of treble in your signal. Left is
less, right is more.
Low cut - Dip switch on the right side of the pedal that cuts
low end.
Ground lift - Dip switch on the left side of the pedal. When
using the XLR output, if you experience a hum you can
switch the ground lift to remove the hum.
Jacks
INPut - 1/4” jack on the right side of the pedal. output - 1/4” jack on the left side of the pedal.
Xlr output - XLR jack on the left side of the pedal. You can use this to go straight into a mixer or interface.
The VCR pedal is a rst in a new collaboration between PaxAM, Ryan Adams, and JHS
Pedals. Inspired by the chorus/reverb tones of The Cure, The Smiths and a hefty dose of
1980’s angst.
Controls
POWER - Uses 9V DC Negative Center. Do not use more than 9V DC. Your warranty will be voided. 80mA max consumption.
VOLUME - Controls the output/boost volume.
VOLUME TOGGLE - Toggle just below the Volume
knob. Engages the boost circuit when ipped
up.
CHORUS - Controls the amount of chorus.
Turning the knob to the left decreases the rate
and increases the mix. Turning the knob to the
right increases the rate and decreases the mix.
CHORUS TOGGLE - Toggle just below the Chorus
knob. Engages the chorus effect when ipped
up.
INPUT - Jack on the right side of the pedal.
OUTPUT - Jack on the left side of the pedal.
Jacks
REVERB - Controls the reverb mix. Left is less
mix and right is more mix.
REVERB TOGGLE - Toggle just below the Reverb
knob. Engages the reverb effect when ipped
up.
LO-FI SWITCH - Switch on the backside of the
pedal that engages a lo-, mid range sound on
the overall tone of the pedal.