Tally Dascom 1330 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. Never carry out maintenance or repair work yourself. Always contact a qualified service technician. Keep this Operator’s Manual in a place which is easily accessible at all times. Place the printer on a solid and even base so that it cannot fall. Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 1330 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 1330 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 1330 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 1330 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 1330 Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. Данная инструкция должна быть всегда доступна каждому пользователю. Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.
Tally Dascom 1330 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. Consulte sempre um técnico qualificado para executar uma reparação . Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 1330 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiyebir uzman servis-teknisyenine haber verin. Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Tally Dascom 1330 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 1330 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 2 1.1 PLACING THE PRINTER ............................................................................................................................ 3 1.2 PRINTER COMPONENTS ...........................................................................................................................
1 Unpacking Guide Place your packaged printer on a solid base. Make sure that the “Up” symbols point in the correct direction. Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer.
1.1 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: Never place the printer near to any flammable gas or explosive substances.
Component Function Top Flap Proect the printerhead and other parts inside .And reduce noise. Paper Guides Print Head Adjust positioning of single sheet paper. 24-pin printing mechanism Head Gap Lever Paper Feed Lever Adjusts the gap between the print head and various form thickness. Shows printer status, for printer setup.
2 Setting Up Printer 2.1 Install Ribbon 1. Switch off the printer. 2. Take off the Front Flap as shown in below picture. 3. Move the Head Gap Lever forward to the most open position, labeled Ribbon. This is to make the biggest gap between the print head and the print bar. 4. Move the printhead to the middle position by hand carefully.
5. Remove the old Ribbon Cartridge before you install the new Ribbon Cartridge.( Skip this step and operate the next step if you install the ribbon for the first time.) 6. Install the Ribbon Cartridge as shown below. Install the recess position labeled ① and ② on ribbon cartridge into the printer mounting. Press the ribbon cartridge slightly in order to make it installed successfully. 7. Pull out the Ribbon guide which is mounted on the Ribbon Cartridge. Press the ribbon guide onto the print head.
Note on Ribbon Cartridge Removal: 1) Eject any paper loaded in the printer. 2) Turn off the printer power. 3) Set the gap lever to the most open position labeled “RIBBON”. 4) Open the front cover. 5) Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 6) Remove the blue ribbon frame from the print head.
2.2 Install the Sheet Feeder As shown in the picture below, ensure the sheet feeder fingers fit into the slots in front of the printer. Push in the sheet feeder until its sides latch on the fixed bolts in the printer. The sheet feeder is now installed successfully. To remove the sheet feeder, use one hand to hold the printer and the other hand to pull and unlatch the sheet feeder. 2.3 Connecting the Interface Cable The 36-pin Centronics parallel and USB ports are located at the rear of the printer.
2.4 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Connect the power cord to the power inlet of the printer. Connect the power cord plug to a mains socket. Switch on the printer.
3 Control Panel Operation 3.1 Keys and LEDs There are 4 keys on the Control Panel, from right to left:【Online】key、 【LF/FF】key、 【Tear-off】 key and【Load/Eject】key.
3.2 Starting up function Self checking When the printer is power off, hold down the 【Online】 key and turn on the printer . After restoration of the printhead is finished. Please load paper and then the printer will start self-checking. The printer will print the version number of the firmware first, and then print current parameter setting and test needles. After then, the printer will printer the list of character set.
4 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter.
5 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. 5.1 Print Quality Problems and Solutions Problem Solution • Make Printing is too light or too dark. Smears and stains appear on the page. Printing is erratic or the wrong characters are printed.
5.2 Paper Handling Problems and Solutions Problem Paper cannot be loaded or fed. Paper jams while loading. Paper jams while printing. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Solution • Make sure that the paper select lever located on the top right of the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor.
5.4 Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner. 5.
5.7 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.
6 General Specifications Item Printing method Printing direction Printing speed Print head Character set Character font Character pitch Column Print matrix (Reference) Paper handling Paper thickness Paper size Paper weight Copy capability Paper through speed Form length Ribbon Description Serial impact dot matrix Bi-Directional logic seeking character, graphics Bi-Directional or Uni-Directional selection LQ (cps) NLQ (cps) Draft(cps) HS Draft(cps) None 450 10 cpi@china 100 200 300 10 cpi@OS 100 2
RAM Factory Optional Units Emulation Noise Operation panel External dimensions Ambient condition Power supply Power cord ESD Reliability Safety marks Others Memory: 8M byte (Input buffer:128Kbytes) USB 2.0 (Full-speed only) Option: RS-232C DB9F Centronics IEEE1284 Compatible \ Nibble mode parallel LAN RJ45 Bluetooth WiFi ESC/P2 、OKI Approx TBD dB(A) (LQ Mode) ISO7779 (ISO Standard) 4 keys + 4 LEDs 369 (W) x 283.
FCC STATEMENT Changes or modifications not expressly approved by the responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable against harmful interference in a residential installation.
DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com UNITED KINGDOM DASCOM GB Ltd Hart House,Priestley Road, Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81,WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.