User Guide 1225 Matrix Printer
Tally Dascom 1225 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 1225 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. x Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. x Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. x Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 1225 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. x Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. x Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. x Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 1225 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. x Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. x Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 1225 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. x Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. x Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 1225 ɉɪɚɜɢɥɚ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ. (Russian) ɉɪɨɱɢɬɚɣɬɟ, ɩɨɠɚɥɭɣɫɬɚ, ɢɧɫɬɪɭɤɰɢɸ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ ɩɟɪɟɞ ɜɤɥɸɱɟɧɢɟɦ ɜ ɪɚɛɨɬɭ ɩɪɢɧɬɟɪɚ. x ɇɟ ɜɵɩɨɥɧɹɣɬɟ ɬɟɯɧɢɱɟɫɤɢɟ ɪɚɛɨɬɵ ɢ ɪɟɦɨɧɬ ɬɟɯɧɢɤɢ ɫɚɦɨɫɬɨɹɬɟɥɶɧɨ, ɧɨ ɫɨɨɛɳɚɣɬɟ ɨ ɧɟɢɫɩɪɚɜɧɨɫɬɹɯ ɤɜɚɥɢɮɢɰɢɪɨɜɚɧɧɵɦ ɫɟɪɜɢɫɧɵɦ ɬɟɯɧɢɤɚɦ. x Ⱦɚɧɧɚɹ ɢɧɫɬɪɭɤɰɢɹ ɞɨɥɠɧɚ ɛɵɬɶ ɜɫɟɝɞɚ ɞɨɫɬɭɩɧɚ ɤɚɠɞɨɦɭ ɩɨɥɶɡɨɜɚɬɟɥɸ. x ɍɫɬɚɧɨɜɢɬɟ ɩɪɢɧɬɟɪ ɧɚ ɪɨɜɧɨɦ ɢ ɫɬɚɛɢɥɶɧɨɦ ɦɟɫɬɟ ɬɚɤ, ɱɬɨɛɵ ɨɧ ɧɟ ɫɦɨɝ ɭɩɚɫɬɶ ɧɚ ɩɨɥ.
Tally Dascom 1225 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. x Consulte sempre um técnico qualificado para executar uma reparação . x Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. x Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. x Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 1225 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı iúletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. x Bakım ve tamir çalıúmalarını kesinlikle ve hiçbir surette kendi baúınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. x Yazıcıyı, üzerinden yere düúmesi mümkün olmayacak sabit ve düz bir zemine yerleútirin.
Tally Dascom 1225 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 1225 X
Tally Dascom 1225 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PLACING THE PRINTER ........................................................................................................................................ 2 PRINTER COMPONENTS ......................................................................................................................................
Tally Dascom 1225 ERROR INDICATIONS ON LEDS ..........................................................................................................................43 DIAGNOSTIC FUNCTIONS ................................................................................................................................... 44 FIRMWARE UPDATE ...........................................................................................................................................
Tally Dascom 1225 1 Unpacking Guide x Place your packaged printer on a solid base. x Make sure that the “Up” symbols point in the correct direction. x Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. x Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer.
Tally Dascom 1225 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: x Never place the printer near to any flammable gas or explosive substances.
Tally Dascom 1225 Component Gap Lever Function Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Paper Guides Adjusts positioning of single sheet paper. Print Head 24-pin printing mechanism Cover Protects print head and other components inside, and reduce noise. Control Panel Shows printer status, for printer setup.
Tally Dascom 1225 2 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions c on the ribbon cassette into the printer mounting. 3. Press the ribbon frame d onto the print head. 4. Turn the ribbon knob e in clockwise direction until the ribbon fabric is taut.
Tally Dascom 1225 Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. Connecting the Interface Cable The 36-pin Centronics parallel and USB ports are located at the rear of the printer. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports.
Tally Dascom 1225 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch “A”, located to the right side of the printer, is in the “O” (off) position.
Tally Dascom 1225 Installing the Windows Driver (Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen on the right. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click “Next” to continue. 3. Select the desired printer model as shown on the right.
Tally Dascom 1225 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 5. Click “Finish” to start the installation process. 6.
Tally Dascom 1225 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right.
Tally Dascom 1225 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled.
Tally Dascom 1225 3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. 4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen. 5. The paper should advance automatically to the print position. The printer is now ready to print in the online state. Paper Guides Tractor Feed Handling 1.
Tally Dascom 1225 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60 cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm.
Tally Dascom 1225 4 Control Panel Operation There are 5 switches S1~S5 and 10 LEDs L1~L10. The meaning and application of each switch and LED are described below. LED Indicators “Power/Paper Out” LED: On: Power on Flashing: Paper out Flashing + buzzer: Paper jam “Online” LED: On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. “Pitch” LEDs: On: Indicates the selected pitch.
Tally Dascom 1225 “LF/FF” Key: Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). “Tear Off” Key: When online, this key will move any loaded continuous paper to the tear-off position. When offline, this key is used to select the desired pitch. “Font” Key: When offline, this key is used to select the desired font. Table 4.
Tally Dascom 1225 Panel Operation There are 3 states of operation: Online, Offline and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, and switch to Offline state. In the Offine state, the keys provide the following functions: Font select, Pitch select, Line Feed/Form feed, Load/Eject, and switch to Online state, micro feed, control PE (paper error) sensitivity, clear buffer and restore factory defaults.
Tally Dascom 1225 Online State Function Name Online Switch Operation {S5} LED L10 Function Description Toggles between Online and Offline states x Load: Automatically loads the paper (according to path selection) when no paper is on the platen. Load/Eject {S4} - x Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen.
Tally Dascom 1225 Offline State Function Name Switch Operation LED Function Description Font {S1} L1~L4 Selects the font. Pitch {S2} L5~L8 Selects the pitch. LF {S3} - Feeds a line with every press of S3. By holding S3, the printer initially feeds a few lines; then feeds FF [S3] - the form to the next TOF for rear tractor or ejects the form for cut sheets. x Load: Automatically loads the paper (according to path selection) when no paper is on the platen.
Tally Dascom 1225 Calibrate PE {S1}+[S2] - sensor x Out-of-paper: Beeps once. Automatically loads a form in 10 seconds. x Paper loaded: Calibrates PE sensor with paper loaded and sensitivity save the sensitivity value. Beeps 5 times when completed. x [NOTE: There are 2 independent sensors for rear tractor and front friction. Restore default [S2]+{S4} Resets PE sensor sensitivity to factory defaults. Beeps twice PE sensor when completed.
Tally Dascom 1225 Power-On State Function Switch Name Operation Menu Setup / [S2] LED - EDS Function Description Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Hex Dump [S4] - Beeps once to indicate going into hex dump mode: x Prints data from host in hexadecimal representation. x Pressing S4 suspends the printing.
Tally Dascom 1225 Restore Factory [S3]+[S4]+[S5] - Defaults Restore settings to factory defaults except for Change Pin, Vertical Alignment and Adjust Page Margin Parameters. Firmware [S2]+[S3]+[S4]+ Update [S5] - x Alternate flashing of L9 and L10 indicates ready for firmware update from host. x When new firmware is being received: L1 and L2 will flash, followed by L1 and L3 flashing, then followed by L1 and L4 flashing. x When downloading is completed, the carriage returns to home position.
Tally Dascom 1225 5. Printer Setting Changes In order to meet individual print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off.
Tally Dascom 1225 HS-Draft On: Prints High Speed Draft On, Off when Draft font is selected. When printing 180x180 DPI Graphic Speed graphics: Normal – prints in 180x180 DPI, Fast – prints in Normal, Fast, Ultra 90x180 DPI, Ultra – prints in 60x180 DPI. IBM Set 1/2 Selects the IBM character Set 1, Set 2 set.
Tally Dascom 1225 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdu 46. Greek DEC 47. Greek ELOT 928 Character Table Character table type Graphic Table, Italic Table selection Page Setup Page Setup Valid Settings Function Print Width 13.
Tally Dascom 1225 Specifies the waiting time before feeding the page to tear-off position automatically. Manual: Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5s Auto tear mode is off. View1s, View2s, View3s: View1s, View2s, View3s After printing is completed, the printer will feed the paper until the last printed line is at the tear-off position. (Applies to tractor mode only) Interface Setup Interface Valid Settings Setup Function For multi-host connection.
Tally Dascom 1225 German (Deutsch) System Setup Valid Settings Emulation ESC/P2, IBM 2390 Plus Auto CR (IBM) Ja, Nein Auto LF Ja, Nein Druck Dir Bi-Dir, Uni-Dir, Auto Top Druck Dir Bi-Dir, Uni-Dir Anschlag Normal, Stark IBM AGM Ja, Nein Druck Setup Valid Settings Font (Andere) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Zeichenteilung 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Null 0,Ø HS-Draft An, Aus Graphikgeschw.
Tally Dascom 1225 Auto IF Delay 10s, 30s RAM Nutzung Ladbarer Font, Puffer CX Bid Ja, Nein Valid Settings Erweitertes Setup Auto Laden Manuell, 0.5s, 1s, 1.
Tally Dascom 1225 Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" 0/60" … 10/60"…99/60" 0/60"…10/60"...30/60" 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60" … 10/60"…99/60" Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60"…10/60"...
Tally Dascom 1225 Menù Stampa Valid Settings Fonte (Altre) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Spaziatura 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0,Ø HS-Bozza Si, No Veloc. Grafica Normale, Veloce, Ultra IBM Set 1/2 Set 1, Set 2 USA, Francia, Germania, Regno Unito, Danimarca, Svezia, Set Carat. Int. Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II, America Latina, Korea, Legal Code Page CP 437, CP 857… Tab.Carattere Tab.
Tally Dascom 1225 Controllo Fonti Software, Ignora Controllo Qualità Software, Ignora Cicalino Si, No French (Français) Setup système Valid Settings Emulation ESC/P2, IBM 2390 Plus RC-Auto (IBM) Oui, Non SL-Auto Oui, Non Dir Impr. Bidir, Unidir, Auto Sup. Dir Impr. Bidir, Unidir Frappe Normal, Forte IBM AGM Oui, Non Setup impression Valid Settings Polices (Autres) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Densités caract.
Tally Dascom 1225 Setup interface Valid Settings Interface Auto, Parallel, USB I-PRIME Oui, Non Auto IF Delay 10s, 30s Utilisation RAM User Font, Buffer CX Bid Oui, Non Setup élargi Valid Settings Chargem. Autom. Manuel, 0.5s, 1s, 1.5s, 2s Prévention bourrage Qui, Non Détec.fin de pap Qui, Non Long.formul.Strg Software, Ignorer Densi.caract.
Tally Dascom 1225 Page Setup Valid Settings Ancho de Impresión 13.6", 8" Lineas Por Pulgada 1, 2, 3, 4, 5, 6, 7, 8 Tamaño Papel Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Margen Sup. Pap Cont. 0/60" … 10/60"…99/60" Margen Inf. Pap.Cont. 0/60"…10/60"...30/60" Tamaño Hojas Sueltas 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margen Sup. Folios 0/60" … 10/60"…99/60" Margen Inf. Folios 0/60"…10/60"...
Tally Dascom 1225 IBM AGM Evet, Hayır Yazdırma Ayarları Valid Settings Yazı Tipi (Diáer) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Karakter Sıklıáı 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Sıfır 0,Ø Yük.Hız-Taslak On, Off Grafik Hızı Normal, Hızlı, Ultra IBM Karakter Seti 1/2 Set 1, Set 2 Amerika Bir.Devleti, Fransa, Almanya, øngiltere, Danimarka, Uluslararası Kar.
Tally Dascom 1225 Karak.Sıkl. Kont. Yazılım, Yoksay Yazı Tipi Kont. Yazılım, Yoksay Kalite Kont.
Tally Dascom 1225 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as follows: Service Menu ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current SettingφVertical Alignment 4. PressɋLF/FFɌkey to select the current setting.
Tally Dascom 1225 printed above. 7. Once the setting which gives the best alignment is found, press ɋOnlineɌ key to exit current level. Printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to save setting. Press ǏOnlineǐ key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail.
Tally Dascom 1225 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure: 1.
Tally Dascom 1225 unit of 1/60 inch. 6. When satisfied with the left margin setting, press ǏOnlineǐ key, printer will print “Save settings˛ Yes”. Press ǏLoad/Ejectǐ key to choose Yes or No, then press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure: 1.
Tally Dascom 1225 Dascom Printer Setup Tool In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient, simple and fast way to control your printer without touching any keys on the operation panel. 1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”. 2. Connect the printer to the system using USB cable 3. Power up the printer. 4. Load paper into the printer.
Tally Dascom 1225 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter.
Tally Dascom 1225 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob.
Tally Dascom 1225 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution • Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly.
Tally Dascom 1225 Paper Handling Problems and Solutions Problem Solution • Make sure that the paper select lever located on the top right of Paper cannot be loaded or fed. the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path.
Tally Dascom 1225 If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds Paper select lever error continuously. Switch the paper select lever back to its correct position. Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner.
Tally Dascom 1225 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. x Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.
Tally Dascom 1225 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.
Tally Dascom 1225 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Speed Font Matrix Print Head Graphics Pitch HS Draft Draft LQ 10 CPI 375/80H 250/120H 83/360H 12 CPI 300/120H 300/120H 100/360H 15 CPI 375/120H 375/120H 125/360H 17.
Tally Dascom 1225 Bitmap Fonts: 1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI Built-In Fonts 6. OCR-B 10, 12, 17, 20 CPI 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI 1. EAN-13 2.
Tally Dascom 1225 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp Code Pages 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdu 46. Greek DEC 47. Greek ELOT 928 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8.
Tally Dascom 1225 Line Spacing 1/6", 1/8", n/60", n/180", n/360" Fanfold Paper Cut Sheet Single ply Paper Specifications Multi-part Width: 76.2mm̚419.1mm Width: 76.2mm̚419.1mm (3"̚16.5"˅ ˄3"̚16.5"˅ Length: Length: 101.6mm min (4" min) 101.6mm̚363.2mm Paper Specifications ˄4"̚14.3"˅ Weight: 52̚90g/ Weight: 52̚82 g/ Thickness: Thickness: 0.065̚0.14mm 0.065̚0.14mm (0.0026"̚0.0055”) (0.0026"̚0.0055") Weight: 40̚52g/ Thickness: 0.
Tally Dascom 1225 Temperature Operating: Ambient Conditions Humidity +5 to +40 °C. Stand-by: -20 to +55 °C Operating: 10 to 90%RH (No condensation) Stand-by: 10 to 90%RH (No condensation) Dimensions 587 mm (W) x 333 mm (D) x 173 mm (H) Weight 8.5 kg Unit type: Power Supply Switching mode power supply Power cord: Detachable Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by: ESD: Less than 7.
Tally Dascom 1225 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission 1 STROBE ¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK ¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT ¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 ¯¯¯¯ INIT Print
Tally Dascom 1225 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 52
Tally Dascom 1225 IBM Character Set 1 IBM Character Set 2 53
Tally Dascom 1225 International character sets International Character Set Commands Country USA Command ˘ESC˚“R”CHRˀ˄0˅ France ˘ESC˚“R”CHRˀ˄1˅ Germany ˘ESC˚“R”CHRˀ˄2˅ UK ˘ESC˚“R”CHRˀ˄3˅ Denmark1 ˘ESC˚“R”CHRˀ˄4˅ Sweden ˘ESC˚“R”CHRˀ˄5˅ Italy ˘ESC˚“R”CHRˀ˄6˅ Spain1 ˘ESC˚“R”CHRˀ˄7˅ Japan ˘ESC˚“R”CHRˀ˄8˅ Norway ˘ESC˚“R”CHRˀ˄9˅ Denmark2 ˘ESC˚“R”CHRˀ˄10˅ Spain2 ˘ESC˚“R”CHRˀ˄11˅ Lat America ˘ESC˚“R”CHRˀ˄12˅ Korea ˘ESC˚“R”CHRˀ˄13˅ Legal ˘ESC˚“R”CHRˀ˄64˅ 54
Tally Dascom 1225 Character Tables Italic 55
Tally Dascom 1225 Graphic 1 Graphic 2 56
Tally Dascom 1225 Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdu 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab.
Tally Dascom 1225 Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.
Tally Dascom 1225 Code Page Tables CP 437 (US) CP 737 Greek 59
Tally Dascom 1225 CP 850 (Multilingual) CP 851 60
Tally Dascom 1225 CP 852 (Eastern Europe) CP 857 (Turkish) 61
Tally Dascom 1225 CP 858 CP 860 (Portugal) 62
Tally Dascom 1225 CP 861 (Iceland) CP 863 (French-Canadian) 63
Tally Dascom 1225 CP 864 Arabic CP 864 Arabic Extended 64
Tally Dascom 1225 CP 865 (Norway) CP 866 (Cyrillic) 65
Tally Dascom 1225 CP 866 Bulgaria CP 1250 Win Latin 2 66
Tally Dascom 1225 CP 1251 Win Cyrillic CP 1252 Win Latin 1 67
Tally Dascom 1225 CP 1253 Win Greek CP 1254 Win Turkish 68
Tally Dascom 1225 8859-1 Latin 1 8859-1 Latin 1 (SAP) 69
Tally Dascom 1225 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 70
Tally Dascom 1225 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 71
Tally Dascom 1225 ISO 8859-15 Euro (Code Page 923) BRASCII 72
Tally Dascom 1225 Abicomp Roman 8 73
Tally Dascom 1225 Coax/Twinax (Hebrew) New-437 (Hebrew) 74
Tally Dascom 1225 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 75
Tally Dascom 1225 Flarro 863 (Hebrew) 865 Hebrew 76
Tally Dascom 1225 CP 1257 866 Ukraine 77
Tally Dascom 1225 866 Kazakhstan Kamenicky 78
Tally Dascom 1225 Mazovia CP 775 79
Tally Dascom 1225 CRO-ASCII Arabic Farsi 80
Tally Dascom 1225 Arabic Urdu Greek DEC 81
Tally Dascom 1225 Greek ELOT 928 82
Tally Dascom 1225 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC .
Tally Dascom 1225 ESC ˘ ESC > ESC = ESC # ESC ˛n m ESC @ ESC ˸n1 n2 ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M ESC N n ESC O ESC P ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 … ESC Z n1 n2 … ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Unidirectional mode(1 line) Set MSB to 1 Set MSB to 0 Can
Tally Dascom 1225 IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one l
Tally Dascom 1225 ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m S
Tally Dascom 1225 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980 USA Phone:+1 (877) 434 13 77 www.dascom.