User Guide DT-210/230 Thermal Receipt Printer
Tally Dascom DT-210/230 User Guide V1.3 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • The device and mains-socket must all times be easily accessible. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this user guide in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall.
Tally Dascom DT-210/230 User Guide V1.3 About This Manual This manual provides information to operators of the DT-210/230 to describe basic operations to enable safe and correct use of the printer. Symbols Description The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. CAUTION: Provides information that must be observed to prevent damage to the equipment or loss of date.
Tally Dascom DT-210/230 User Guide V1.3 TABLE OF CONTENTS ABOUT THIS MANUAL.................................................................................................................................. II 1 PRODUCT OVERVIEW ................................................................................................................................ 1 1.1 Features ..........................................................................................................................................
Tally Dascom DT-210/230 User Guide V1.3 5.5 Auto Cutter Enable/Disable Selection................................................................................................................ 51 6 TROUBLESHOOTING .................................................................................................................................. 52 6.1 Error Status .................................................................................................................................................
Tally Dascom DT-210/230 User Guide V1.3 1 PRODUCT OVERVIEW Tally Dascom’s DT-210/230 offers high-speed label printing for a wide range of terminal equipment including data, POS, and kitchen terminals. With extensive features, they can be used in a wide range of applications such as food service, retail and grocery. With an internal memory large enough to store logos, footers, custom fonts, keywords and downloading custom applications, this unit has it all.
Tally Dascom DT-210/230 • User Guide V1.3 The DT-210/230 is ENERGY STAR qualified. (Some configurations may be exempted, depending on their components.) Others • Wide range of connectivity. The USB interface is standard interface. Serial/parallel/Ethernet/ Wi-Fi/ Bluetooth are optional interfaces. Various interface choices suit all needs. • Built-in USB interface is also available for all interface models. • The DT-210/230 Software & Documents Disc (drivers, utility, and manuals).
Tally Dascom DT-210/230 User Guide V1.3 1.2 Unpacking Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. Check the printer for any visible transport damage and missing items. If you find any transport damage or any accessories are missing, please contact your dealer for assistance. Please keep the packaging material for future transportation. The shipping list varies with different customized order requirements.
Tally Dascom DT-210/230 User Guide V1.3 Shipping List Items Printer Interface Cable Cover Power Adapter Power Cord Roll Paper -Test Graphic Installation Guide QTY. 1 unit 1 piece 1 piece 1 piece 1 piece 1 piece CD 1 piece Remarks including user guide, graphic installation guide, Driver and demo tool 1.3 Product Configurations There are two models in this series.
Tally Dascom DT-210/230 Model User Guide V1.3 Power Adapter Power Cord Interfaces Paper Cut Sensor 100-240 USB Cashbox PAR SER ETH Wi-Fi Fiscal EN/UK/EU Cutter Tear Bar Black Mark DT-210 √ √ √ O O O O O √ N √ O DT-230 √ √ √ O O O O O √ √ √ O Remarks: “√” indicates standard configuration, “O” indicates optional configuration. PAR=Parallel interface; SER= Serial interface; ETH=Ethernet interface. 1.
Tally Dascom DT-210/230 User Guide V1.3 1.4.1 Power Switch Turn the printer on or off. The marks on the switch: (O: OFF / | : ON) Before turning on the printer, be sure to check that the AC adapter is connected to the power supply. 1.4.2 Control Panel Power LED Error LED Paper LED Feed key LEDs Power LED (green) • Lights when the power supply is on. • Goes out when the power supply is turned off. Error LED Lights or flashes when the printer is offline.
Tally Dascom DT-210/230 User Guide V1.3 Feed Key Pressing this key once feeds the roll paper by one line. Holding this button down feeds the roll paper continuously. 1.4.
Tally Dascom DT-210/230 User Guide V1.3 2 SETUP This chapter describes the setup and installation of the product and peripherals. 2.1 Flow of Setup This chapter consists of the following sections along with the setup flow of the product and peripherals. 1. Installing the Printer (page 9 ) 2. Changing the Paper Width (page 10) 3. Setting the Dip Switches (page 48) 4. Attaching Power (page 11) 5. Adjusting the Paper Near-End Sensor (page 12) 6. Printing Self-test (page45) 7. Installing Driver (page 16) 8.
Tally Dascom DT-210/230 User Guide V1.3 2.2 Installing the Printer You can install this printer horizontally. With an optional mounting plate (P/N: 99501), you can also attach the printer to a wall. Important Notes on Horizontal Installation: • The printer must be installed horizontally on a flat surface (not tilted). • Do not place the printer in dusty locations. • Do not knock or strike the printer. This may cause defective print. • Do not catch cables or place foreign matter under the printer.
Tally Dascom DT-210/230 User Guide V1.3 2.3 Changing the Paper Width The printer is initially set to print on 80 mm width paper and you can change the printer to print on 58 mm width paper by installing the roll paper guide and changing the paper width setting with customized value. Follow the steps below to install the roll paper guide. 1. Open the roll paper cover. 2. Hold the paper separator and carefully pull it out in the direction of arrow. 3.
Tally Dascom DT-210/230 User Guide V1.3 2.4 Attaching Power Checking the voltage of the power adapter Before you connect the power adapter to the power socket check if the voltage is correct. If you connect the power adapter to power with incorrect voltage this may result in electrical damage to adapter and printer. 1. 2. 3. 4. Make sure the printer and the computer are powered off. Connect the power cord to the power adapter.
Tally Dascom DT-210/230 User Guide V1.3 2.5 Adjusting the Paper Near-end Sensor Below are two situations where a paper near-end sensor adjustment is required. • To adjust the detection position to suit the diameter of the roll paper core used. • To adjust the detection position of remaining amount of paper. CAUTION! Since roll paper cores vary slightly in shape, depending on paper roll design and manufacturing tolerances, it is impossible to detect the remaining paper exactly.
Tally Dascom DT-210/230 User Guide V1.3 2.6 Loading Roll Paper WARNING! When opening the cover, take care not to touch the print head or cutter blade. Otherwise, burning or injury of hand may result. 1. Press the cover open button to open the cover. 2. Remove the used roll paper core, if any. 3. Insert the paper roll with its print area facing down as shown in the figure.
Tally Dascom DT-210/230 User Guide V1.3 4. Install the media in the correct direction. 5. Pull out some roll paper, and close the cover. 6. Tear off the paper with the manual cutter till you hear a click sound.
Tally Dascom DT-210/230 User Guide V1.3 2.7 Installing Optional Kits Interface Cover Adjust the relative positions between interface cover and printer as shown below, and push the interface cover as arrow shows below. Splash Cover (optional kit) Slip the fixed hooks on both sides of splash cover into the mounting hole on the printer, and close the splash cover. Mounting Plate (optional kit) 1. Mount the plate on the lower housing of the printer with screws. 2.
Tally Dascom DT-210/230 User Guide V1.3 3 INSTALLING DRIVER Installing the Windows Driver (Compatible with Windows) Switch off the printer before running the printer driver setup. Your printer CD-ROM comes with Windows drivers. Go to the related folder and run the driver setup installer. 1. Double click the driver. You will see the screen as below. Click “Install” to continue.
Tally Dascom DT-210/230 User Guide V1.3 2. Choose the desired port to use, after selecting the “Port” option (USB001 for USB port, com1 for serial port and LPT1 for parallel port), click “Next” to continue. 3. Click “Finish” to finish the installation process successfully.
Tally Dascom DT-210/230 User Guide V1.3 3.1 Installation Driver for Ethernet and Wi-Fi Interface 1. 2. Install the printer driver as USB installation. Click “Start”→ “Devices and Printers”, right click on the DT -230 Printer Driver, and then click “Printer Properties”. 3. Then you will see the screen as below. Click “Ports” → “Add Port”.
Tally Dascom DT-210/230 User Guide V1.3 4. Select “Standard TCP/IP Port”, and click “New Port”. 5. You will see the screen as below, click “Next” to continue.
Tally Dascom DT-210/230 User Guide V1.3 6. Complete the “Printer Name or IP Address” and “Port Name”. 7. Click “Next” to access the screen as below.
Tally Dascom DT-210/230 User Guide V1.3 8. And then you will see the screen as below, click “Next” to continue. 9. Click “Finish” to complete the printer driver installation.
Tally Dascom DT-210/230 User Guide V1.3 10. Click “Start”→ “Devices and Printers”, right click on the DT-230 Printer Driver, and then click “Printer Properties”. Then click “Ports”→ “Configure Port”, finish the setup parameter in the screen as below. Click “OK” to finish the setup.
Tally Dascom DT-210/230 User Guide V1.3 3 CONNECTING TO COMPUTER NOTE! Be sure to install the driver before connecting the printer to the host computer. Before installing, disconnect the Power Unit from the printer (as well as turning the power switch off). Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the power unit is connected can cause damage to the interface board and the printer.
Tally Dascom DT-210/230 User Guide V1.3 3.1 For USB Interface CAUTION! Be careful not to insert the USB interface cable into the cash drawer kick-out connector. 3.2 For Cash Draw Interface 1. Confirm that the power switch is OFF. 2. Confirm the top and button of the cash drawer cable connector and insert it into the cash drawer kick-out connector at the back of the printer. 3. Screw the cash drawer’s ground wire to the body of the printer.
Tally Dascom DT-210/230 User Guide V1.3 3.3 For Serial Interface WARNING! Be sure to turn off the power supply for both the printer and host computer before connecting the cables. 1. Insert the interface cable connector firmly into the interface connector on the connector panel. 2. When using the connectors equipped with screws, tighten them to secure the connectors firmly. 3.
Tally Dascom DT-210/230 User Guide V1.3 3.4 For Parallel Interface 1. Insert the interface cable connector firmly into the interface connector on the connector panel. 2. Press down the clips on either side of the connector to lock it in place. 3. When using interface cables equipped with a grounding line, attach the ground line to the screw hole marked “FG” on the printer. 4. Connect the other end of the interface cable to the host computer. 3.
Tally Dascom DT-210/230 • 1. User Guide V1.3 have surge protection. Otherwise, the devices can be damaged by lightning. Never attempt to connect the customer display cable, drawer kick-out cable, or the standard telephone line cable to the 10/100BASE-T LAN connector. Switch on printer, press and hold the Reset key for more than 3 seconds with the tip of pen or small tool. Then the printer will print out a status sheet as shown below. The following are printed on the status sheet. •TCP/IP settings.
Tally Dascom DT-210/230 2. User Guide V1.3 The interface is pre-set with the IP address 192.168.0.31. DHCP is disabled. Enter this IP address in your browser to get access to the built in web page. Item Information 3.
Tally Dascom DT-210/230 User Guide V1.3 5. After TCP/IP setup, click “Submit”, you will see the following interface. Then click “Reset” button, the parameter will be valid. 6. Configuration page supports initializing TCP/IP parameter. Click Configuration→Network→Reset, you will see “FACTORY DEFAULT” button. Click the button, Ethernet board TCP/IP parameter will return to factory default setup. IP Address is 192.168.0.31.
Tally Dascom DT-210/230 User Guide V1.3 3.6 For Wireless LAN Interface If your printer connected to the computer with Wireless Ethernet, there are two ways of connection modes: AP mode and STA mode. When using the wireless LAN interface, the network configuration is required. Make the settings on setup page. If your printer connected to the computer with Wireless Ethernet, there are two ways of connection modes: AP mode and STA mode. 1.
Tally Dascom DT-210/230 User Guide V1.3 2. You will see “DT-230_WIFI” in the wireless network connection list. Click “Connect”. 3. Double click “DT-230_WIFI” for connection. It will display “Connected” if connection is successful.
Tally Dascom DT-210/230 User Guide V1.3 3.6.1 Get IP Address There are two methods to get the IP address of the printer. One way is to look at the Wi-Fi parameter sheet. The other way is to look into the Wi-Fi connection details after your printer is connect to the computer via Wi-Fi module. Here is the procedure: 1. Open the control panel Network and Internet Network Connections. Then you can see this page: double click “Wireless Network Connection”.
Tally Dascom DT-210/230 2. User Guide V1.3 Click “Details” button on this page.
Tally Dascom DT-210/230 3. User Guide V1.3 Then you can see the IP Address on the Property “IPv4 Default Gateway”: 192.168.0.33 There are two kinds of working mode for Wlan board connection to the PC. One is AP mode, the other one is STA mode. AP means Access Point (AdHoc Mode); STA means Station mode (Infra Structure Mode). We would suggest you use AP mode for your initial usage.
Tally Dascom DT-210/230 User Guide V1.3 3.6.2 Wlan Setup - AP mode 1. Visit IP Address http://192.168.0.33. Default username is “admin” with password “admin” for the first time to log in. You will see the following Wi-Fi setup page. Click “Submit” button after modifying the parameter. Restart printer, new parameter will be valid.
Tally Dascom DT-210/230 User Guide V1.3 2. Log into work mode option, then choose AP mode. Click “Save” button after modifying the parameter. Restart printer, new parameter will be valid. 3. Log onto AP setting, Click “Save” button after modifying the parameter such as channel, encryption mode, and IP address. Restart printer, new parameter will be valid.
Tally Dascom DT-210/230 User Guide V1.3 3.6.3 Wlan Setup - STA mode In the Wi-Fi parameter, if there is IP Address, it suggests they are connected successfully by STA mode. Otherwise, they are not connected. Like showed in the picture below, they are connected successfully. 1. Visit http://192.168.0.33. Default username is admin with password admin for the first time to log in. You will see the following Wi-Fi setup page. Click “Submit” button after modifying the parameter.
Tally Dascom DT-210/230 User Guide V1.3 3.6.4 Return to Factory Setting There are two methods to restore factory setting. Method One: 1. Turn off the printer. 2. Press and hold the black button on the Wlan board. And then turn on the printer. 3. Wait for five seconds, the Wlan board will return to factory setting. Method Two: Visit http://192.168.0.33. Default username is admin with password admin for the first time to log in. Click OK on the Restore Page.
Tally Dascom DT-210/230 User Guide V1.3 3.7 Connecting to Bluetooth Communication cable is not required while using Bluetooth printer. Users have to prepare a Bluetooth adapter by themselves and install the adapter in the computer so as to connecting the Bluetooth device. 3.7.1 Installing Bluetooth Adapter Driver 1. Install Bluetooth adapter (V2.0 or above version) that prepared by yourself in the PC via USB interface. 2. Power on printer and load paper roll. 3.
Tally Dascom DT-210/230 4. User Guide V1.3 Select “Device is ready for searching”, and then click “DASCOM DT-230” for searching the Bluetooth printer. 5. Then the Bluetooth adapter has been installed in the computer.
Tally Dascom DT-210/230 User Guide V1.3 3.7.2 Changing Printer Port 1. Right click any printer, select Properties → Interface, and select the output port that you have put down then click “Apply”.
Tally Dascom DT-210/230 2. User Guide V1.3 Right click any printer, select Properties → Interface, and select the output port that you have put down (in the case COM6) then click “Apply”.
Tally Dascom DT-210/230 User Guide V1.
Tally Dascom DT-210/230 3. User Guide V1.3 Select Normal → Interface, run test page to see the printing outcome. Setting pages vary depending on the different types of Bluetooth adapter. 3.7.3 Changing Baud Rate of the Printer The baud rate of the printer and that of the Bluetooth board should be of the same frequency. The default baud rate of the Bluetooth I/F is 115200 bps, so you have to change the DIP setting so as to change the printer baud rate.
Tally Dascom DT-210/230 User Guide V1.3 4 SETTING/CHECKING MODES Besides the ordinary print mode, the printer has the following modes to set or to check settings of the printer. • Self-test Mode • Hexadecimal Dumping Mode 4.1 Self-test Mode Before you connect the printer to the computer, make sure that the printer is in proper working order. You can do this by printing a configuration status label. Follow the steps below to run this mode. 1.
Tally Dascom DT-210/230 User Guide V1.3 Here is the self test status page and its explanation. The printout is an example. It may differ depending of installed options or interfaces: SELF-TEST Model Firmware Version S/N Model DT-230 Firmware Version : SV1.02.
Tally Dascom DT-210/230 User Guide V1.3 4.2 Hexadecimal Dumping Mode This function is to print out all received data in hexadecimal numbers. If printing cannot occur correctly, this function allows checking whether or not the printer is receiving data correctly. Follow the steps below to run this mode. 1. Open the roll paper cover. 2. While pressing the FEED button, turn on the printer. 3. Close the roll paper cover.
Tally Dascom DT-210/230 User Guide V1.3 5 SETTING DIP SWITCHES On this printer, you can make various settings such as printer density, baud rate, and auto-cutter enable/disable etc. with DIP switches. The DIP switches are already set for the current interfaces. Change the setting if necessary. Functions of the DIP switches differ depending on the interface. 5.1 Setting Procedure Follow the steps below to change the DIP switch settings.
Tally Dascom DT-210/230 User Guide V1.3 4. Replace the DIP switch cover, and screw it in place. New DIP switch settings are enabled after the printer is turned on! 5.2 For Serial Interface (RS-232C) When using the built-in USB interface, it is not necessary to change the DIP switch setting but their function changes. For the details, see “For Parallel and USB2.0 Interface” .
Tally Dascom DT-210/230 2-4 2-5 2-6 2-7 2-8 User Guide V1.3 BUSY Condition Print Density Offline or Receive Buffer Full Receive Buffer Full See “Selecting the Print Density” on page 48. Near-End Sensor Status Disable Enable OFF OFF OFF OFF OFF 5.3 For Parallel and USB2.0 Interface When using the serial interface, it is not necessary to change the DIP switch setting but their function changes. For the details, see “For Serial Interface (RS-232C)” on page 47 .
Tally Dascom DT-210/230 User Guide V1.3 5.4 Selecting the Print Density 2-5 2-6 ON OFF ON OFF ON OFF OFF ON • • 2-7 Print Density (Mono color) Reserved Reserved Reserved Reserved 1 (Light) 2 (Standard) 3 (Darker than standard) 4 (Dark) If the print density is set to 3 or 4 level, printing speed may be reduced. The print density can be set with DIP switches or the customized value. 5.
Tally Dascom DT-210/230 User Guide V1.3 6 TROUBLESHOOTING Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer for assistance. Read the following instructions before maintenance and avoid incorrect operation, so as to prevent injury to you and damage to the printer. 6.
Tally Dascom DT-210/230 Vertical dot line missing User Guide V1.3 Dirty thermal head or print Thermal head damaged Clean the thermal head or print roller. Contact your dealer for assistance. 6.2 Removing Jammed Paper When a paper jam occurs, never pull out the paper forcibly. Open the roll paper cover and remove the jammed paper. When the cover cannot be opened, follow the steps below to remove the jammed paper. Printhead may be hot, please do not touch! 1. Turn off the printer. 2.
Tally Dascom DT-210/230 User Guide V1.3 4. Close the cutter cover. 5. Open the printer cover and remove the jammed paper. 6.3 Cleaning Thermal Head DASCOM recommends cleaning the thermal print head periodically (generally every 3 months) to maintain receipt print quality. • • After printing, the thermal print head becomes very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the thermal print head by touching it with your fingers or any hard object.
Tally Dascom DT-210/230 User Guide V1.3 7 SPECIFICATIONS 7.1 Printer Specification Print method Resolution Print speed Print width Interface Print Parameter Print density Power consumption Memory RAM Flash Receive buffer Characters per line User-defined Fonts Code page Chinese Character Barcodes 1D 2D Graphics Detect Function Power Supply Sensors Input Output Paper Handling Paper type Direct thermal line printing 203DPI, 8dots/mm DT-230: 260mm/s Default; 240-270mm/s adjustable via DIP.
Tally Dascom DT-210/230 Paper width Paper thickness Paper roll diameter Paper load Paper cut Emulation Noise Physical Spec. Operating condition Storage condition Dimensions Color Weight Optional Kits Accessory Reliability Software Certification Head lifetime MTBF Cutter lifetime MCBF Driver User Guide V1.3 79.5±0.5mm/57.5±0.5mm 0.056~0.1mm Max. OD ∮83mm Min. ID ∮13mm Upward cover open and Easy paper loading Manual tear; Auto-cutter (hay cutter type) and partial cut.
Tally Dascom DT-210/230 User Guide V1.3 7.2 External Dimension and Mass • • • • Width: Approximately 147 mm {5.78”} Depth: Approximately 203.9 mm {8.03”} Width: Approximately 149.2 mm {5.87”} Mass: DT-210: Approx. 1.6kg {3.53lb} (excluding power adapter) DT-230: Approx. 1.7kg {3.
Tally Dascom DT-210/230 User Guide V1.3 7.3 Interfaces Power Supply interface, USB interface and cash drawer interface are standard interfaces for the printer. Serial interface, Parallel interface, Ethernet interface and Wi-Fi interface are optional interfaces for the printer. The interface pin assignment is listed below. 7.3.1 USB interface USB interface pin assignment PIN No. 1 2 3 4 Description VBUS DD+ GND Classic wire color Red White Green Black USB interface connector diagram 7.3.
Tally Dascom DT-210/230 User Guide V1.3 7.3.3 Serial interface Serial interface pin assignment Serial interface compatible with RS-232 standard, with 25 pin (D hole type) socket. PIN No. Description PIN 1 Frame Ground PIN 2 TXD PIN 3 RXD PIN 4 RTS PIN 5 Unconnected PIN 6 DSR PIN 7 Signal Ground PIN 8~19 Unconnected PIN 20 DTR PIN 21~25 Unconnected User can view the setting of interface via printing configuration sample.
Tally Dascom DT-210/230 3 Pin No. 4 5 6 7 8 9 H Signal From H H H H H H 10 P 11 P 12 P 13 14 15 16 17 18 19~30 31 32 33 34~35 36 User Guide V1.3 Data 1 Description Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 (The highest bit) ACK Signal; Printer response signal, indicates that the printer has received a Data byte. Busy Signal; The printer is busy; High level indicates that the printer can’t receive data. PE Signal; Paper end signal; High level indicates that the printer is out of paper.
Tally Dascom DT-210/230 User Guide V1.3 7.3.5 Ethernet interface Ethernet interface pin assignment Pin. No. Name Description 1 TX+ TXRX+ n/c n/c RXn/c n/c Tranceive Data+ Tranceive DataReceive Data+ Not connected Not connected Receive DataNot connected Not connected 2 3 4 5 6 7 8 Ethernet interface connector diagram 7.3.6 Wi-Fi interface Wi-Fi interface supports 2.4 GHz, IEEE Std. 802.11b standard. 7.4 Power Adapter Power Socket pin assignment Pin Number 1 2 3 SHELL Signal Name +24 V GND N.C F.
Tally Dascom DT-210/230 User Guide V1.3 7.5 Paper Specification Paper type Form Roll paper diameter Size Min. core diameter Take-up roll paper width Paper width Specified thermal paper Roll paper 83 mm {3.27"} maximum 13mm 80 + 0.5/-1.0 mm 79.5 ± 0.5 mm CAUTION • Paper must not be pasted to the roll paper spool. • The remaining amount of the roll paper when a roll paper near-end is detected differs depending on the spool type. 7.5.
Tally Dascom DT-210/230 User Guide V1.3 58 mm paper width printing The printable area of a paper with width of 57.5 ± 0.5 mm {2.26" ± 0.02"} is 50.8 ± 0.2 mm {2.00" ± 0.008"} (360 dots), and the space is approximately 3.7mm {0.15"} on the left side and approximately 3.0 mm {0.12"} on the right side. 57.5 ± 0.5 mm {2.26 ± 0.02"} 0.141 ± 0.05 mm {0.056 ± 0.002"} 50.8 ± 0.2 mm {2.00 ± 0.008"} 3.7 ± 0.2 mm {0.15 ± 0.079"} 3.0 ± 0.2 mm {0.12 ± 0.079"} All the numeric values are typical.
Tally Dascom DT-210/230 User Guide V1.3 7.5.2 Printing and Cutting Positions Last line of a previous receipt Approx. 29 Manual-cutter position Auto-cutter blade position Approx. 15 Paper feed direction Center of the print dotline [Units: mm (All the numeric values are typical. The values may vary slightly as a result of paper slack or variations in the paper. Take this into account when setting the cutting position of the auto cutter.
Tally Dascom DT-210/230 User Guide V1.3 8 CHARACTER CODE PAGES • • The character code tables show only character configurations. They do not show the actual print pattern. “SP” in the table shows a space. 8.1 Common to All Pages (International Character Set: USA) HEX 0 0 1 NUL 2 DLE 00 16 XON 1 01 18 XOFF 3 03 6 EOT 04 ENQ A D E F 5 07 6 38 ‘ 23 08 39 24 40 09 25 41 * 10 26 ESC 11 FF FS 13 43 < 29 = 45 .
Tally Dascom DT-210/230 User Guide V1.3 8.2 International Character Sets ASCII code (Hex) Country 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E USA # $ @ [ \ ] ^ ` { | } ~ France # $ à ° ç § ^ ` é ù è ¨ Germany # $ § Ä Ö Ü ^ ` ä ö ü β U.K. £ $ @ [ \ ] ^ ` { | } ~ Denmark I # $ @ Æ Ø Å ^ ` æ ø å ~ Sweden # ¤ É Ä Ö Å Ü é ä ö å ü Italy # $ @ ° \ é ^ ù à ò è ì Spain I Pt $ @ ¡ Ñ ¿ ^ ` ¨ ñ } ~ Japan # $
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 ]8.
Tally Dascom DT-210/230 User Guide V1.3 8.
Tally Dascom DT-210/230 User Guide V1.3 9 PRINTING CONTROL COMMAND SETS · Be compatible with ESC/POS command set · Support NV image and page mode printing List of Commands Command HT LF FF CR CAN DLE EOT DLE ENQ DLE DC4 ESC FF ESC SP ESC ! ESC $ ESC % ESC & ESC ∗ ESC − ESC 2 ESC 3 ESC = ESC ? ESC @ ESC D ESC E ESC G ESC J ESC L ESC M ESC R ESC S ESC T ESC V ESC W ESC \ Name Horizontal tab Print and line feed Print and return to standard mode (in page mode) Print and carriage return Cancel print data in p
Tally Dascom DT-210/230 Command ESC a ESC c 3 ESC c 4 ESC c 5 ESC d ESC p ESC t ESC { FS g 1 FS g 2 GS ! GS $ GS ( A GS ( D User Guide V1.
Tally Dascom DT-210/230 Command GS ( k User Guide V1.3 Name Set up and print symbol PDF417: Set the number of columns in the data region. PDF417: Set the number of rows. PDF417: Set the width of the module. PDF417: Set the row height. PDF417: Set the error correction level. PDF417: Select the options. PDF417: Store the data in the symbol storage area.
Tally Dascom DT-210/230 User Guide V1.3 The commands listed below in the first column are defined as “obsolete commands” in the ESC/POS command system. This printer supports both upward-compatible commands and obsolete commands. However, the upward-compatible commands are recommended to use.
Tally Dascom DT-210/230 User Guide V1.3 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
DASCOM REPRESENTATIVES GERMANY SINGAPORE (ASIA PACIFIC) DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com AMERICAS UNITED KINGDOM DASCOM Americas Corporation 24 Lakeview Court Verona, VA 24482 USA Phone:+1 (877) 434 13 77 Fax: +1 (540) 242 7221 www.dascom.
