Tally Dascom 5130P Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessibleat all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 5130P Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. • Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. • Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. • Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 5130P Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. • Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. • Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. • Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 5130P Indicazioni di sicurezzaimportanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. • Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. • Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 5130P Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nuncalleve a cabo trabajos de mantenimiento o reparación Ud. mismo,sino consultea un técnico de servicio calificado. • Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. • Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 5130P Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. • Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. • Данная инструкция должна быть всегда доступна каждому пользователю. • Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.
Tally Dascom 5130P InstruçõesImportantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. • Consultesempre um técnico qualificado para executar uma reparação . • Coloquea impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. • Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. • Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 5130P Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. • Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiyebir uzman servis-teknisyenine haber verin. • Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Tally Dascom 5130P TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of DigitalEquipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 5130P X
Tally Dascom 5130P TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PREPARE THE PRINTER ......................................................................................................................................... 2 TRACTOR INSTALLATION ........................................................................................................................................
Tally Dascom 5130P ERROR INDICATIONS ON LEDS ............................................................................................................................ 36 DIAGNOSTIC FUNCTIONS.................................................................................................................................... 37 FIRMWARE UPDATE ........................................................................................................................................... 38 8 SPECIFICATION ........
Tally Dascom 5130P 1 Unpacking Guide • Place your packagedprinter on a solid base. • Make sure that the “Up” symbols point in the correct direction. • Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. • Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing,please contact your dealer.
Tally Dascom 5130P Preparethe Printer Remove the packaging materials from the printer as follows: 1-2: Remove all the visible tape from the outsideof the printer. 3: Open the printer front cover. 4: Remove the transparent cover. 5: Remove the cable ties from the left and right ends of the carriage shaft. 6: Remove the shipping cardboard from around the print head. 7-13: Remove the shipping foams from around the chassis. 14: Install back the transparent cover.
Tally Dascom 5130P Tractor Pair Installation If you want to use continuous fanfold paper, you have to install the tractor pair assembly. Before installing the tractor pair assembly, the printer rear cover must be removed first. Below instructions show how to install and remove both the printer rear cover and tractor pair assembly. Removing and installing the printer rear cover: 1. Ensure there is no loaded paper in the printer. Switch off the printer. 2.
Tally Dascom 5130P Installing and removing the tractor pair assembly: 1. To install, first insert the upper cylindrical fingers at both ends of the tractor assembly into the metal frame at the back of the printer (see picture “7”). Tilt the tractor assembly downwards, and use your index fingers to push the lower cylindrical fingers at both ends slightly upwards until they are mounted at the bottom of the printer metal frame (see picture “8”). 2.
Tally Dascom 5130P Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enoughspace for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: • Never place the printer near to any flammable gas or explosive substances.
Tally Dascom 5130P Printer Components Component Function Control Lever Lift up the top of mechanism to install or remove ribbon Paper Loader Paper feed path for single sheet and passbook. Print Head 24-pin printing mechanism Cover Protects print head and other components inside, and reduces noise.
Tally Dascom 5130P 2 Setting Up Printer InstallRibbon 1. Ensure the power to the printer is off. 2. Press the recesses of both sides to open the cover. Remove the transparent cover. 3. Push the control lever to lift up the top of mechanism, and make sure the control lever is set to the latched position. 4. Move the print head to the center of the carriage.
Tally Dascom 5130P 5. Install the recess positions on the ribbon cartridge into the printer mounting, and push both sides of the ribbon cartridge to ensure they click into position. 6. Press the ribbon guides onto the print head from underneath until they click into position. 7. Turn the ribbon knob until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly.
Tally Dascom 5130P 8. Pull down the control lever to set the top of mechanism to its original position, and make sure the control lever is fully latched. 9. Install back the transparent cover to reduce noise. 10. Close the cover carefully. When the printer is in operation, ensure the cover is closed to keep the dust away and minimize the noise level. Open the cover only for cleaning, clear paper jam or ribbon replacement.
Tally Dascom 5130P Notes on RibbonCartridge Removal: 1. 2. 3. 4. Eject any paper loaded in the printer. Turn off the printer power. Open the front cover. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 5. Remove the blue ribbon guides from the print head. 6. Use fingers to take hold of the ribbon cartridge firmly, and pull the cartridge towards you to unlatch it. 7.
Tally Dascom 5130P Connecting the Mains Power Checkingthe printer voltage Make sure that the device has been set according to your country’s power supply voltage.To do this, check the ratingplate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. 1. Make sure the printer and the computer are powered off. 2.
Tally Dascom 5130P Installing the Windows Driver (Compatible with Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen below. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown below. Choose the desired port to use. Click “Next” to continue.
Tally Dascom 5130P 3. Select the desired printer model as shown below. Click “Next” to continue. Cancel 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box below. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue.
Tally Dascom 5130P 5. Click “Finish” to start the installation process.
Tally Dascom 5130P 7. After installation is completed successfully, you will see the message below.
Tally Dascom 5130P 3 Paper Installation Guide Paper and Printable Area Specifications The printer can handle following forms: 1)Cut sheet papers and slips 2)Passbooks 3)Multipart carbonpapers up to 1+3 copies 4) Continuous fanfold paper (for Tractor version) Cut sheet F B A Printable area E Printable area of cut sheet Position Dimension Definition A 4.23 mm +2/-0 mm Top margin B 3.12 mm +2/-1 mm Right margin E 5 mm +2/-0 mm Bottom margin F 3.
Tally Dascom 5130P Passbook with horizontal seam F G B A Printable area C D Printable area E Printable area of passbook with horizontal seam Position Dimension Definition A 5 mm +2/-0 mm Top margin B 5 mm +2/-1 mm Right margin C 5 mm +2/-0 mm Center margin D 5 mm +2/-0 mm Center margin E 5 mm +2/-0 mm Bottom margin F 5 mm +2/-1 mm Left margin 17
Tally Dascom 5130P Passbook with vertical seam F D C B A Printable area Printable area E Printable area of passbook with vertical seam Position Dimension Definition A 5 mm +2/-0 mm Top margin B 5 mm +2/-1 mm Right margin C 5.2mm +2/-0 mm Center margin D 5.2mm +2/-0 mm Center margin E 5 mm +2/-0 mm Bottom margin F 5 mm +2/-1 mm Left margin Passbook thickness Position Dimension Definition A Max 0.5 Cover page height B 0.2-0.5 Cover page thickness C Max 1.
Tally Dascom 5130P Note: (1)Make sure the cover is closed when operating the printer, as there is a cover open detect sensor. (2)Do not load media that is curled or folded. (3)Do not use media that attaches any metal, such as staple. (4)Do not load passbook that is damaged, wrinkled or with loose centre seam. (5)Do not use passbook that has sticky glue. (6)Do not use passbook in which the inner pages are smaller than cover pages. (7)Print on the inner pages of the passbookonly.
Tally Dascom 5130P Inserting a passbook 1. Power on the printer. After initialization, only the “ON” LED should remain on. 2. While pressing the center seam and with printable side facing up, insert a passbook into the paper loader until the edge of the passbook engages snugly with the platen. The passbook should advance automatically to the print position. Now the printer is ready to print as shown below. Tractor Feed Handling (for Tractor version) 1.
Tally Dascom 5130P 4 Control Panel Operation (Tractor version) Labeling L1 DATA L2 ON L3 Shared with S1 top label L4 Shared with S2 top label L5 Shared with S3 top label S1 Top: USER1; Bottom: Load/Eject S2 Top: OFFLINE; Bottom: - S3 Top: USER2; Bottom: LF/FF On the controlpanel are: Three keys: USER1, OFFLINE and USER2 Five LEDs: DATA, ON, USER1, OFFLINE and USER2. ON LED colour is green while the others are orange. The meaning and application of each key and LED are described below.
Tally Dascom 5130P Operating State Upon power-on, L1~L5 turn on briefly. After initialization, only L2 remains ON. In the Operating State, the LED indications and switch functions vary with Online/Offline modes and emulations.
Tally Dascom 5130P USER1 Online mode Single sheet path selected: - If paper is loaded from the front, pressing this key will eject the paper. Paper eject direction depends on configuration setting. - If paper is loaded from the Tractors, pressing this key will not have any effect. - If paper is not loaded, pressing this key will not have any effect (since paper from the front will auto-load). Tractors path selected: - If paper is loaded from the Tractors, pressing this key will park the paper.
Tally Dascom 5130P USER2 Online Mode Single sheet path selected: - If paper is loaded from the front, pressing and releasing this key will feed paper one line forward. If key is pressed down for more than 1 sec, printer will eject the paper. Paper eject direction depends on configuration setting. - If paper is loaded from the Tractors, pressing this key will not have any effect. - If paper is not loaded, pressing this key will not have any effect.
Tally Dascom 5130P Power-On Functions with Cover Open USER1 OFFLINE X X USER2 Utilities Remarks L1&L2 blink alternatively. BOOT or Firmware Upgrade X X X Self Test Print Font- and Codepage test page Self Test Endless running ASCII TREE Self Test Configuration test page with menu settings X* Suspend cover open *Press OFFLINE after power on. The detection printer resets and goes online.
Tally Dascom 5130P ● Enable/Skip listing of current settings ● ● ● ● ● System Setup I/F Setup ESC/P2 Emulation IBM X24 Emulation Restore Factory Defaults X X Hex-Dump Self-Test (Font and Codepage Test Page) With the cover closed, hold USER1 at power-on till the printer resets to activate the Self-Test. Single mode: Load an A4 to start the self-print. Tractors mode: Paper will auto load and start print.
Tally Dascom 5130P Setup Menu With the cover closed, holding USER1 and USER2 at power-on brings up the Setup Menu. The printer resets and L1~L2=ON and waits for paper insertion. All printed dialogs in the Setup Menu are viewed in up-right orientation as in Fig. 2. [NOTE: 1xxx dialog is up side down when viewed by users.] Rear of printer Setup dialog English Deutsch … Fig.2---Setup dialogs in up-right orientation viewed by operators.
Tally Dascom 5130P Configuration Profiles The termination of Listing Current Configuration brings the Edit Profile menu. Successive pressing of USER2 scrolls out remaining choices, highlighted in brown. Edit Profile: Menu1 Menu2 Restore Factory Defaults [USER1]=OK [USER2]=Next NOTE: Menu1 and Menu2 cannot assign the same I/F. Menu1=Profile for USER1; Menu=Profile for USER2.
Tally Dascom 5130P Configuration Menu (Sample) 29
Tally Dascom 5130P 5 Default Settings System Setup System Setup Valid Setting Menu2 Menu1(Default) (Default) Emulation Epson, IBM Epson IBM Buzzer Yes, No, PE off Yes, No, No No No No Media Passbook, Multi-part, Thin Form Passbook Passbook Auto CR Yes, No, No No Auto LF Yes, No, No No Thick Mode Yes, No No No Line Wrap Around Note1: Passbook: normal impact strength for PB/Slip. Multi-part=stronger impact. Thin Form=Slow feeding to avoid paper crumble.
Tally Dascom 5130P Set Sweden, Italy, Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal Table 437 Table 437 Graphic Table Graphic Table Set 1, Set 2 Set 2 Set 2 CPL 94, 90, 80 94 94 Condensed 16.6, 17.1 17.1 16.
Tally Dascom 5130P ESC/P2 Emulation ESC/P2 Emulation Valid Setting Menu1 (Default) Menu2(Default) Print Dir Auto,Uni-Dir,Bi-Dir Auto Auto Paper Eject Front,Rear Front Front Continuous print Yes,No NO NO IBM Emulation System Setup Valid Setting Menu1 (Default) AGM(X24) Auto Load Reset After Eject Form Length TOF IBM-PP LIKE BOF IBM-PP LIKE No,Yes Yes,No Yes, No 12,11 No,Yes No,Yes No No No Yes No No 12 12 No No No No Restore Factory Defaults 1.
Tally Dascom 5130P 6 Maintenance Your printer requiresvery little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the mannerdescribed in this chapter.
Tally Dascom 5130P 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution • Make sure that the ribbon cartridge is properly installed and that Printing is too light or too dark.
Tally Dascom 5130P Paper Handling Problems and Solutions Problem Solution • Make sure that the paper select lever located on the top right of Paper cannot be loaded or fed. the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. Paper jams while loading.
Tally Dascom 5130P If paper is loaded and the paper select lever is moved to the Paper select lever error incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position. PrinterFailures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved,contact your dealer or service partner.
Tally Dascom 5130P Diagnostic Functions The printer diagnostic functionsare Self-Test page, hex-dump mode and print alignment adjustment. • Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface,or the computer.
Tally Dascom 5130P Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmwarefile may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.
Tally Dascom 5130P 8 Specification Print System Monochrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Pitch HS Draft* Draft HS-LQ (CPS/DPI) 10 CPI 400 CPS 300 CPS 200 CPS 100 CPS 360 CPS 240 CPS 120 CPS 12 CPI Print Speed 15 CPI 17.1 CPI 20 CPI *limited print width of 8.
Tally Dascom 5130P Bitmap Fonts: Draft 10, 12, 15, 17.1, 20, 24 CPI Roman 10, 12, 15, 17.1, 20 CPI, Proportional Built-In Fonts OCR-B 10 CPI in NLQ and LQ; 12, 17.1, 20 CPI, Proportional OCR-A 10 CPI in NLQ and LQ, 12, 17.1, 20 CPI, Proportional Courier,Gothic, SanSerif, Prestige elite, Script, Orator, bold all in NLQ and LQ style and 10, 12, 15, 17.1, 20 CPI, Proportional (via programming) 1. EAN-13 2. EAN-8 3. Interleaved 2 of 5 4. UPC-A Barcodes 5. UPC-E 6. Code 39 7. Code 128 8. POSTNET 9.
Tally Dascom 5130P 20. CP 1254 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 30. Roman8 31. Coax/Twinax Code Pages 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. Siemens Turk. 43. DEC Turkish 44. CP 775 Baltic 45. CRO-ASCII 46. Arabic Farsi 47. Arabic Urdu 48. Greek DEC 49.
Tally Dascom 5130P 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8. Spain I 9. Japan 10. Norway 11. Denmark II 12. Spain II 13. Latin America 14. Korea 15. Legal Cut Sheet Width: 60 – 245 mm Length: 67 – 363.2 mm Weigth: 52 – 157 g/m² Thickness: 0.0. – 0.12 mm Paper Specifications Continuous Form Width: 101.6 – 241.3 mm Length: 139.7 mm and above Weight: 64 – 100 g/mm² Thickness: 0.06 – 0.
Tally Dascom 5130P Windows Server 2000/2003/2008 Windows Drivers Windows Vista Windows XP Windows 98 Windows 7 Interface Parallel (Bi-directional IEEE-1284 nibble mode) RS232C (9-pin Sub-D male IF) USB 2.0 (B type connector) Operation Panel Switches: 3 pcs Noise Level Less then < 55 dBA, Draft Mode (ISO7779 pattern) LED indicators: 5 pcs Temperature Operating: Ambient Conditions Humidity +5 to +40 °C.
Tally Dascom 5130P 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission 1 STROBE,¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK,¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT,¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 INIT,¯¯¯¯ Prin
Tally Dascom 5130P 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 45
Tally Dascom 5130P IBM Character Set 1 IBM Character Set 2 46
Tally Dascom 5130P International character sets International Character Set Commands Country USA France Germany UK Denmark1 Sweden Italy Spain1 Japan Command <ESC>“R”CHR$(0) <ESC>“R”CHR$(1) <ESC>“R”CHR$(2) <ESC>“R”CHR$(3) <ESC>“R”CHR$(4) <ESC>“R”CHR$(5) <ESC>“R”CHR$(6) <ESC>“R”CHR$(7) <ESC>“R”CHR$(8) 47
Tally Dascom 5130P Norway Denmark2 Spain2 Lat America Korea Legal <ESC>“R”CHR$(9) <ESC>“R”CHR$(10) <ESC>“R”CHR$(11) <ESC>“R”CHR$(12) <ESC>“R”CHR$(13) <ESC>“R”CHR$(64) Character Tables Italic 48
Tally Dascom 5130P Graphic 1 Graphic 2 49
Tally Dascom 5130P Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdu 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab.
Tally Dascom 5130P Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.
Tally Dascom 5130P Code Page Tables CP 437 (US) CP 737 Greek 52
Tally Dascom 5130P CP 850 (Multilingual) CP 851 53
Tally Dascom 5130P CP 852 (Eastern Europe) CP 857 (Turkish) 54
Tally Dascom 5130P CP 858 CP 860 (Portugal) 55
Tally Dascom 5130P CP 861 (Iceland) CP 863 (French-Canadian) 56
Tally Dascom 5130P CP 864 Arabic CP 864 Arabic Extended 57
Tally Dascom 5130P CP 865 (Norway) CP 866 (Cyrillic) 58
Tally Dascom 5130P CP 866 Bulgaria CP 1250 Win Latin 2 59
Tally Dascom 5130P CP 1251 Win Cyrillic CP 1252 Win Latin 1 60
Tally Dascom 5130P CP 1253 Win Greek CP 1254 Win Turkish 61
Tally Dascom 5130P 8859-1 Latin 1 8859-1 Latin 1 (SAP) 62
Tally Dascom 5130P ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 63
Tally Dascom 5130P ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 64
Tally Dascom 5130P ISO 8859-15 Euro (Code Page 923) BRASCII 65
Tally Dascom 5130P Abicomp Roman 8 66
Tally Dascom 5130P Coax/Twinax (Hebrew) New-437 (Hebrew) 67
Tally Dascom 5130P New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 68
Tally Dascom 5130P Flarro 863 (Hebrew) 865 Hebrew 69
Tally Dascom 5130P CP 1257 866 Ukraine 70
Tally Dascom 5130P 866 Kazakhstan Kamenicky 71
Tally Dascom 5130P Mazovia CP 775 72
Tally Dascom 5130P CRO-ASCII Arabic Farsi 73
Tally Dascom 5130P Arabic Urdu Greek DEC 74
Tally Dascom 5130P Greek ELOT 928 75
Tally Dascom 5130P 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC .
Tally Dascom 5130P ESC : ESC < Copy ROM to RAM Unidirectional mode(1 line) ESC > ESC = ESC # ESC ?n m Set MSB to 1 Set MSB to 0 Cancel MSB control Reassign graphics mode ESC @ ESC \n1 n2 Initialize printer Set relative horizontal print position ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M Set n/60″line spacing Set/cancel vertical tabs Set page length in lines Set/cancel horizontal tabs Select Bold Cancel Bold Select double-strike mode Cancel do
Tally Dascom 5130P IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensedmode Online Select 10CPI Offline Cancel double-wide mode(one l
Tally Dascom 5130P ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m S
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
DASCOM REPRESENTATIVES GERMANY UNITED KINGDOM RUSSIA and CIS DASCOM Europe GmbH DASCOM GB Ltd DASCOM Europe GmbH Heuweg 3 ViewPoint, Basing View, Representation Moscow D-89079 Ulm Basingstoke, Hampshire Leninsky Prospekt 95a, Office 322 Deutschland RG21 4RG, England 119313 Moscow, Russian Federation Tel.: +49 (0) 731 2075 0 Phone: +44 (0) 1256 481481 Phone: +7 (495) 984 70 65 Fax: +49 (0) 731 2075 100 Fax: +44 (0) 1256 481400 Fax: +7 (495) 984 56 42 www.dascom.com www.dascom.com www.