User's Guide

Part of introduction
Best wear the wristband behind
malleolus ulnaris;
Adjust the size suitable for the
size of wrists via Adjustment Hole,
fasten wrist strap buttons;
Sensor shall be close to skin
avoiding moving.
Charging method
In the state of the wristband shutdown, Charging or long press the red
side button for 3 seconds the watch will power on.
When the wristband is in the boot state, Switch to the shutdown interface,
long press the interface or press the red side button for 3 seconds, the
wristband vibrates and shuts down.
Power on/off
Matters needing attention
Please avoid strong impact, extreme heat and exposure to the wristband.
Please do not disassemble, repair or transform the device on its own.
Common problems
Basic parameter
1.32InchFullRoundFullTouch
Adjustment HoleDisplay screen
Wrist strap
Sensor
Left Hand
Malleolus ulnaris
1.
2.
1.
2.
3.
Because of the problem of signal interference in Bluetooth wireless connection,
there may be no time to connect each other. If the connection is not long
enough, please ensure that the operation is carried out without magnetic field
or without multi Bluetooth device interference.
Turn off Bluetooth and open.
Turn off the mobile phone background application or restart the mobile phone.
Mobile phones do not connect to other Bluetooth devices or functions at the
same time.
APP is running normally in the background and may not be connected if it is
not in the background.
What do Bluetooth connections do? (connection / reconnection failure or
connection speed is slow)
Confirm whether your device system is Android 4.4 or its higher versions , and IOS9.0 or
its higher versions, and your device support Bluetooth 4.0.
a.
b.
c.
d.
e.
Can't search the wristband?
Since the wristband is not searched by phone in Bluetooth broadcast, make
sure the wristband is in power and activated and is not connected to any
other phones. Then, put the wristband close to the phone, if it is still invalid,
turn off the phone, and after about 20 seconds, restart the phone Bluetooth.
Why the wristband should be worn more tightly when measuring heart
rate?
The wristband uses light reflection principle, penetrates the skin through the light
source, and collects the signal reflected to the sensor, to calculate your heart rate. If
you don't wear it tightly, there will be ambient light reaching into the sensor, which
will affect measurement accuracy.
Why not remind when opening the reminder function?
Android phone: confirm that the phone and the wristband are connected, and
open the corresponding permissions in the phone settings, allowing the " GloryFit"
APP access calls, messages and address book, and keeping "GloryFit" running in the
background; if the phone is installed with security software, add " GloryFit" to "trust".
Iphone: If there is no reminder after the connection, it is recommended to restart
the phone to reconnect, when reconnecting the wristband again, there will be
reminder after popping up "Bluetooth pairing request" and clicking "Pairing".
Is the wristband waterproof?
It supports IP68 waterproof and dust-proof level (IP68 standard is 35 degrees
below water, 1 meters below 30 minutes). Usually, wash hands, rain, cold water
shower, wash car can be worn with heart.
For the first time, please take the wristband out and charge the equipment with the
corresponding charger. When charging, the wristband will open automatically.
(charge mode as follows: Joint the USB-charging cable with Band at match point
back side and USB port for charging. Charge voltage 5V.)
1. When the device starts up, to touch the screen or slide the interface to lighten screen or
switch over display;
2. The screen shall be screen off without operation for 5 seconds and users can connect the
phone to App to modify the screen off time.
3. The wristband is default as open status for calling and message reminding,user can connect
to App and change the open/off status.
4.Press the Return Button (differ from red button) at any time to return back to main Interface.
operation
Install the wristband APP
Bluetooth connection: after successfully matching, APP will automatically save
the wristband bluebooth address. When APP is opened or operated in
background, it will automatically search and link with the wristband.
Data Synchronism: manually pull down the synchronization data on the
APP home page; the bracelet can store off-line data for 7 days, the more
data, the longer the synchronization time is, and the longest time is about 2
minutes.
Scan the following QR codes or enter into various large application
markets to download and install “ GloryFit”.
When being used for the first time, it is necessary to connect APP for
alignment. After successful connection, wristband will self-synchronize
time, or otherwise, step calculation and sleep data won't be accurate.
Device requirement: iOS9.0 and above; Android 4.4 and above to
support bluetooth 4.0 .
After entering into APP, please first set up personal
information.
Me Click avatar
→
Personal information and exercise goals
Reminding function
For reminding function, a reminding switch shall be switched on in APP-end
Setting Center, mobile phone and wristband shall be kept to be connected
successfully and there will be vibrating reminders when there are messages.
Open mobile phone APP
Click to set up icons
↓
Add device (iOS)/
Add device(Android)
↓
Click the upper right to find the icon
↓
Click device attachment
·
·
Head portrait, gender, age, height and weight
can be set up and personal information can
enhance accuracy of data.
Customize personal everyday exercise goals. A
reasonable exercise plan is helpful for promoting
body quality.
number of the caller is displayed. (if the caller's name has been saved in the
phone address book, the name is displayed, otherwise the display number)
Message reminding : when a text message arrives, the wristband will vibrate
and display the SMS icon reminder; the address message of the address book
contact person displays the name, and the short message number of the
stranger.
QQ reminding : when the QQ information arrives, the ring will vibrate and
display the QQ icon.
WeChat reminding : when the WeChat information is received, the hand ring
will shake and the WeChat icon reminds
Alarm clock reminding : it can set up three alarm clocks, and will synchronize to
the bracelet after setting up. The intelligent alarm clock is a silent alarm clock.
When the alarm is on, the bracelet will cause moderate vibration, and support
the offline alarm clock reminder.
Other reminding : when receiving email or other information, the wristband
vibrates and displays other reminder icons. Click to see the content.
Charging : When the wristband is connected to the power supply or charged
by the charging clamp, the motor vibrates, and the wristband does not vibrate.
Main functional interface
Main interface
Sleep detection function
When you fall asleep, the wristband will automatically determine the sleep monitoring mode,
automatically detect your deep sleep / shallow sleep / wakefulness time, calculate your sleep
quality, and sleep data temporarily support APP only.
Note: you can get sleep data when you go to sleep with a hand ring.
Wristband factory default to open calls and SMS reminders，Users can
choose to open or close in the main interface of the APP.
3.
Settings interface
click the screen to view historical information, such as no history
1.32 inch large screen, large font, more content display, easy to see.
Switch to the interface to see the current number of steps, distances and
calories. The distance and calories are calculated and displayed on the
basis of the current walking steps and the height and weight set by the
· When the test, the icon will beat and the back heart rate of the hand
· When testing, the sensor should stick to the skin to avoid the influence
· To keep the test area clean, sweat or stains will affect the test results.
You can enter the sub menu by click on the related interface, and then
perform and operate more related functions.
This machine is charged with 5V 500MA, and it is strictly forbidden to use
overvoltage load power.
The use of the environment is 0 degrees ~45 degrees, and it is forbidden to
throw it into the fire so as not to cause an explosion.
Please wipe off the water with a soft cloth and then the wristband can be
used for the charging operation , otherwise it will cause corrosion of
charging contact point and charging inciddent may occur.
Do not touch the chemical substances such as gasoline, clean solvent,
propanol, alcohol or insect repellent.
Please do not use this product in high pressure and high magnetic
environment.
If you have sensitive skin or tighten the wristband, you may feel
discomfortable.
Please dry the sweat drips on the wrist in time. The strap has long contact
with soap, sweat, allergies or pollution ingredients, which may cause skin
allergy itching.
If it is often used, it is recommended to clean the wristband every week.
Wipe with wet cloth and remove oil or dust with mild soap.
It is not appropriate to wear a hot bath with a wristband.
After swimming, please wipe the wristband in time so as to keep dry.
·
·
·
·
·
·
·
·
·
·
·
Does the Bluetooth connection need to be open all the time? Is there any
data after disconnection?
Before the data is synchronized, the data is kept on the wristband host (seven days of data
can be retained). When the Bluetooth connection of the wristband and the wristband is
successful, the wristband data will be automatically uploaded to the mobile terminal. Please
synchronize the data to the mobile terminal in time.
Note: if the caller and SMS alerts are opened, you must keep the Bluetooth connection, and
the alarm is offline.
Switch to the interface, click the screen to enter into the specific sports
interface, including rope skipping, swimming, riding, pingpang, tennis,
badminton such six modes, slide the screen then enter the specific sports
interface.
Sports interface
The wristband has multiple main interfaces,
and the interface can be switched after click
on the main interface. After the first pairing
of APP, the wristband will synchronize the
time, date and week of the cell phone.
WeChat reminding : When the steps reach the target set on the APP, the
wristband will vibrate and display the target reaching icon.
Blood pressure interface
Switch to the blood pressure interface, click the screen to start testing blood
pressure. Once blood pressure test completed press side button to exit the
blood pressure mode. If test start it will show the results of the last test or "-/-"
when the results are not measured; also you can connect to the phone App, in
the blood pressure interface once the test stop, test result same as above.
Information interface
In the message interface, click the main screen to view the message,slide the
screen to turnover the pages. Press the side button to exit the interface.
interface , If the watch is not worn correctly or failed, the final failure interface
will be displayed. Under the heart rate detection mode, the duration of the
watch will be reduced.
Switch to the heart rate interface, click the screen to enter the heart rate
detection. After the test is completed, press side button to exit the heart rate
detection. You can also connect to the mobile phone App, in the heart rate
interface test stop. If the bracelet is not worn correctly or failed, the final
failure interface will be displayed. Under the heart rate detection mode, the
duration of the bracelet will be reduced.
Heart rate interface
To test your heart rate, you need to take a long time signal to accurately
calculate your heart rate.
Why is the first test of heart rate too long?
Call Message QQ WeChat Alarm clock Sedentary Other Charging
Settings
Table tennis Cycling Tennis
Gymnasice Indoor Running
Brightness Find
Info
Reset
off
Hockey
Brightness adjustment : Click the main screen to adjust different brightness,
there are the 4 levels that you can click to choose any of them.
Find the phone: In the connection state, click the screen to interfact of find
the mobile phone, the phone will ring out to remind.
Version information: Under the About interface, you can view the firmware
version number and Bluetooth address of the watch.
Restore settings: Long press on the restore interface, and all the record data
will be erased, and the APP data will be cleared that day (the rest of the
historical data will remain).
Shutdown: The interface can be shut down after you click the interface menu
and the wristband will vibrate.
Return: Press the side button of the breacelet to exit
Main interface setting
Type
1.32 Inch Full Touch Smart Watch
Display Size 1.32Inch
Weight 54.5g
Length 25.5cm
Waterproof Level Ip68
Material TPU
Temperature
Switch to the temperature interface, click the screen to enter the temperature
detection. After the test is completed, press side button to exit the temperature
detection. You can also connect to the mobile phone App, in the temperature
Temperature interface
Quick instructions for use
Wearing method
Device attachment
APP functions and setting
Call reminding : when the caller calls, the ring will shake and the name or
enter the mobile phone APP to revise off-screen time; vibrate and display other reminder icons,Click the viewable content.
menu until test stop. If the bracelet is not worn correctly or failed, the final
failure interface will be displayed.
Smart watch
User Guide
Message push interface
information and display is empty.
APP individual.
Heart rate test note:
ring LED lights will be lit;
of external light on the accuracy of the test.
Status interface
Blood
Oxygen
Sports
Heart
rate
Blood
pressure
Information
Ba ery Type Li-Polymer
Ba ery Model 531727
Ba ery Capacity 200mAh
Ba ery Voltage DC 5.0V
Ba ery Power 0.74Wh
Package
Device, Manual,Charging Dock