Operation Manual

34 35
Diagnosis of Problems and Solutions
Problems Checking Solutions
The motor can not be
started normally
Power plug not properly
inserted
Leakage protection
disconnected
Motor overheated or
overloaded
Causes motor to stop
Make sure the power cord is inserted
into the 3-core grounded metal
receptacle.
Reset circuit breaker. If the problem
persists, the power system may be
defective. Power off immediately and
confer with an expert.
Allow the motor to cool naturally and
start it again.
Filter
Unable to rinse the pool
No sand in the body
Location error of the control
valve
Excessive dirt in water
Filter barrel blocked
Sand filling Refer to sand filling
instructions
The control valve rotates to the filter
position
to prolong the running time
Clean the lter barrel
The filter is unable to
discharge water or the water
ow rate is too slow
There is blockage at the
inlet
There is an air leakage at
the gap of the inlet
Excessive dirt in water
Filter medium is blocked by
impurities
The pool is connected with
a cleaning device
Check and clear away the blockage in
the water pipes
Tighten the nozzle nuts and check the
damaged point of the nozzle and water
height
Clean the lter screen
Backwash
Disassemble the cleaning device
connected to the pool
Filter fails to run Water level is too low
Filter screen is blocked
Air leakage from the inlet
pipe
Motor or blade is blocked
Inject water to adjust water level
Clean the lter screen in the pool
Tighten the nozzle and check the
damaged point
Replace the ttings
Water leakage on the control
valve or upper cover
The seal ring of the body is
lost or too dirty
The control valve retainer
is not tightly secured
ordamaged
Remove the upper cover of the control
valve and sleeve the seal ring of the
body
Clean the seal ring of the body with a
water pipe
Tighten the screw with a screwdriver
Replace the ttings
The manometer fails to run The inner wall of the
manometer is blocked
The manometer is damaged
Remove the manometer from the
control valve and clear away the
impurities on the inner wall
Replace the ttings
Sand enters the pool The sand particles are too
ne
Use 20# quartz sand only
Particle size of the sand is 0.45-0.85mm
Or replace the sand
SFP6-16-GB(V1) SFP6-16-F(V1)
Positionnement
de la valve de
commande
Fonctions Direction de l'écoulement d'eau
Filtre
Filtration normale pour rincer la
piscine
L'eau circule dans le lit ltrant où se
trouve la pompe de ltration à sable
puis entre dans la piscine
Rétrolavage
Circulation de l'eau en sens
inverse pour rincer le lit ltrant
L'eau circule dans le lit ltrant où se
trouve la pompe de ltration à sable
puis est directement déversée depuis
la sortie d'évacuation.
Rinçage
Cette fonction est utilisée lors de
la première installation. Le sable
dans le réservoir de sable est
rincé et la couche de sable après
le rétrolavage est aplanie.
L'eau circule dans le lit ltrant où se
trouve la pompe de ltration à sable
puis est directement déversée depuis
la sortie d'évacuation.
Egout
Déversée directement depuis
la sortie d'évacuation, utilisée
pour diminuer le niveau d'eau ou
déverser l'eau provenant de la
piscine
Déversée directement depuis la sortie
d'évacuation de la pompe de ltration
à sable sans passer dans le lit ltrant
Circulation
Fait circuler l'eau de la piscine
sans passer dans le lit ltrant.
L'eau coule directement vers la
piscine par la valve de commande de
la pompe de ltration à sable sans
passer dans le lit ltrant
Fermé
Circulation d'eau fermée entre le
ltre et la piscine
/
F
i
l
t
r
e
R
i
n
ç
a
g
e
C
i
r
c
u
l
a
t
i
o
n
R
é
t
r
o
l
a
v
a
g
e
F
e
r
m
é
E
g
o
u
t