User's Manual

1.Overview
1.1 Features
1.2 Specifications
· LTE & WCDMA & GSM
· WiFi hotspot
· ACC detection for ignition status
· IP65 water proof
· Remote cut-off (petrol/power)
· Multiple alerts
SIM card should have access to GPRS and SMS.
Remove the cover, switch the device to OFF and insert the SIM
card in correct direction.
1.3 Accessories
12V relay
SOS cable
Power cable
Frequency
GPS
Location accuracy
GSM: 850/900/1800/1900 MHz
Working
voltage/current
Chipset : U-blox 7020
Frequency: GPS L1, 1575.42MHz
<10 meters
WiFi
LED indicator
2.4 GHz
GPS (blue), GSM(green), power (red)
Battery 450mAh/3.7V
Operating
temperature
Dimension
-10℃～40℃
113(L)*51(W)*20(H)mm
Weight 105g
LTE:B1/B2/B3/B4/B5/B7/B8
WCDMA: 850/900/1900/2100MHz
(B1/B2/B5/B8)
9-36V
12VDC/76mA(12VDC); 38mA(24VDC)
2.Device appearance
3.Wiring Diagram
A1
A2
Red PW+ Power: 9v～36v
Orange ACC ACC
A3
A4
Yellow Relay Fuel/Power cut-off
Black GND GND
A5
A6
Purple SOS + SOS (Positive)
white SOS - SOS (Negative)
Status
0.3s ON, 0.3s OFF
GSM
GPS
POWER
Definition
GSM initializing
1s ON, 3s OFF
0.1s ON, 3s OFF
GSM normal
GPRS online
OFF No GSM or SIM card
4.LED indications
Green LED(GSM indicator）
5.Hardware Operation
(1)SIM Card installation
Status
0.3s ON, 0.3s OFF
Definition
Low battery
1s ON, 3s OFF
Solid Red
Work normally
Charging
OFF
Solid ON
Note: LED indicators will be off after 180s when ACC is OFF.
No battery/Malfunction
Red LED（Power indicator）
Status
0.3s ON, 0.3s OFF
Definition
Searching GPS signal
1s ON, 3s OFF
OFF
GPS positioned successfully
GPS sleeps or doesn’t work
Bluetooth configuration
Blue LED(GPS indicator）
(1) Add SOS number via SMS command
Send SMS command: SOS,A,number1,number2,number3 #
(A means add number).
3 SOS numbers can be set. If set successfully, the terminal will
reply “ok”.
e.g. SOS,A,13510****60,135116****6,136126****8#
(set all 3 SOS numbers)
SOS,A, 13510****60# (set the first SOS number)
SOS,A, ,135116****6# (set the second SOS number)
SOS,A, , ,136126****8# (set the third SOS number)
(2) Delete SOS Numbers
Send SMS command: SOS, D,1,2,3#
(D means delete SOS number)
e.g. SOS, D,1# means delete the first number
SOS, D,3# means delete the third number
If you don’t know the sequence number, you can also delete
the number by SMS command like this: SOS,D,number#
e.g. SOS,D,13527852360# means delete this SOS number
directly.
It will reply “OK” if the number is deleted successfully.
(3) Add SOS numbers via platform
You can set SOS number via the platform or APP when device
is online.
Set center number：
CENTER,A,phone number#
Delete center number：
CENTER,D#
8.Operations & Functions
8.1 SOS number
8.2 APN setting
The following operation can be achieved through the terminal
platform or APP provided by the dealer.
6.Device Installation
7.Wiring
- Under the dash board below the front windshield;
- In the parcel shelf in the rear;
- In the front bumper (non-m aterial face), make sure the
device does not get wet;
- Under the wiper version (non-m etal), make sure the
device does not get wet;
- Non Covert Installation - fix the device on the dash
board below windshield.
1. The standard voltage is 9V-36V, the red wire is the
positive, the black wire is the negative.
2. Connect the black wire to ground.
Under rear windshield
Un
der front windshield
Around dashboard
Device
Device
Device
You need to choose somewhere that it won’t be found,
because the whole point of fitting covert GPS vehicle
tracker is the secrecy element.
1. Your device has built-in GSM antenna and GPS antenna
.
During installation, please make sure the receiving side
face is up ; any high power devices such as reversing
radar, anti-theft device or comm unication equipment
would affect the signal of the device.
2. All metallic cases of the windshield will attenuate the
signal on the tra
cking device. It’s sim ply due to the
shielding effects of the m etal com pound of the case.
3. The device should be fixed into position with cable ties
or wide double-side tape.
Yellow
Orange
Black
Red
Ignition key
Pump
2A FUSE
１２／２４Ｖ
Storage
batter y
12V or 24V
Relay
NOTE:
Please pay attention to the diagram description,
battery is 9-36V and relay remains 12V / 24V.
SOS
To ensure GPRS is activated, please make sure APN is
correct. You can send SMS command to set APN:
APN command format:
APN,APN's Name#
E.g: APN,internet# “( internet” is the APN of carrier)
The device will reply“OK”if setting successfully.
Default platform is
www.tracksolid.com
To connect to other platform, please send the SMS
command to change the DNS or server IP:
DNS :
SERVER,1,DNS,Port,0#
E.g: SERVER,1,gpsdev.tracksolid.com ,21100,0#
IP:
SERVER,0,IP,Port,0#
I
t will reply “ OK” after set successfully.
Note: The APN of some countries have user name and
password, you may need to send SMS command as
following:
APN,APN name,user name,password#
8.3 Server setting
8.4 Center number
Command
TIMER,T1,T2#
T1: ranges from 0/5～18000 seconds, the upload interval when
ACC ON
T1=0: no data uploaded
T1=5～18000 seconds (Default: T1=10)
T2: ranges from0/5～18000 seconds, the upload interval when
ACC OFF
T2=0: no data uploaded
T2=5～18000 seconds (Default: T2=0)
8.5 Upload positioning data regularly
Delay time for device entering arming state after the vehicle
power is off and ACC is in low-level. In the arming state, if the
vehicle vibrates for a few times, it will activate the vibration
alarm system. If the vehicle battery is still not on (ACC is in low
level) after 3 minutes, the device will start vibration alarm.
SMS format:
DEFENSE,TIME#
The time ranges from 1 to 60 minutes, default is 10.
NOTE:
1. Preset SOS numbers before sending SMS alarm messages
and calls.
8.6 Arming time setting
8.7 Wire cut-off alarm
2. If there is no need for vibration alarm, please send SMS
SENALM,OFF# to close it.
When the electricity supply of device is cut off, it will
activate cut-off alarm. In this case, the device will send
related SM S to the SOS num bers and dial the numbers in
circles. If nobody answers, the call just keeps 3 loops at
most. At the meantim e, the device will upload power cut
off alarm data to the serv er. And it will send:
Cu offt P Alarmower ！< 06-17 14:53>，
http://m aps.google.com /m aps?q=N22576713,E113.9165
85
NOTE:
The SOS numbers should be preset, please refer to 8.1.
1. via platform
Send oil cut-off com mand on platform . To make sure the
security of vehicle, tracker can only indicate to cut off oil
when GPS is in valid position status, and the speed is less
8.8 Oil cut-off
NOTE:
To ensure the safety of the driver and the car, this
comm and is valid only under two conditions: the GPS is
located; the speed is less than 20km/h.
2. Via SM S
Firstly, you should set a center num ber. Please refer to 8.4.
Only center number can send the com mand to the device
to cut off and restore oil.
The format is:
RELAY,1#
After the com mand is carried out, it will reply “RELAY:ON”
If the com mand didn't carry out, it will reply the reason
about fail to carry
out.
than 20KM /H or in static. Plat
form account password is
needed when sending oil cut off comm and.
When the alarm is off, sending recover oil com mands
manually. Device will restore oil supplying, and vehicle will
work norm ally again.
Platform account password is needed when sending oil
cut off com mand.
2. Via SM S
Only center number can send the com mand to the device
to restore oil.
The format is:
RELAY,0#
After the com mand is carried out, it will receive ”RELAY:0FF”
1. Via platform
8.9 Restoring Oil
When the car is moving over a limited speed in average in
a lim ited tim e period, then the device will send over
speed alarm SM S to user.
To turn on the over speed function, please send below
SMS comm and:
SPEED,ON,Tim e,Lim ited speed,way of alarm#
8.10 Over Speed Alarm
Time range（ Second ）: 5-600s (default as 10s).
Lim ited speed range（ km /h ）: 1-255, default： 100.
Way of alarm : 0, GPRS only; 1, SM S+GPRS; default： 1.
Example:
SPEED,ON,10,120,1#
Means when the car is m oving over 120 km/h in average in
10 seconds, the device will send over speed al
arm to user.
SMS comm and form at: to set all parameter
"FACTORY#"
to default factory value. Once received “FACTORY:OK!”
it succeeds.
8.11 Restore to factory setting
When there is something wrong with the link of GPRS,
e.g., the param eter setting of the device is correct, but you
can't track the car on the platform. At this m om ent you
can send a comm and to the device to reboot the device.
The format is:
RESET#
8.12 Reboot device
In emergent case, press SOS for 3 seconds to activate SOS
alarm. Then the device will send SOS SMS to preset SOS
numbers and dial the numbers in a loop for 3 times till the call
picked up. Alarm message will also be sent to the platform.
After receiving this com mand, the device will reboot after
20 seconds
8.13 SOS
Command:
HOTSPOT,S,N,P#
S=ON/OFF Default: OFF (uppercase required)
N=Name, 20 characters, default: last four digits of IMEI
P=Password, minimum eight, default password: 11111111
8.14 Wi-Fi hotspot
9.Platform & APP
Please login the designated service platform to set and
operate the device.
9.1 Login service platform
Please download and install the APP in designated website,
APP store or Google Play.
9.2 Download APP
After receiving this com mand, the device will reboot after
20 seconds
10. Warning
Battery specified by manufacturer is recommended.
CE Caution:
Use the Product in the environment with the temperature
Between -10℃ and 40℃; Otherwise, it may damage your
product. Products can only be used below 2000m altitude
For the following equipment:
Product Name: 4G Vehicle GPS Tracker
Model: JM-VL01, GV40, VL01
Brand Name: Jimi
Shenzhen Jimi IOT Co., Ltd
E-mail: [e-mail]
hereby declares that this [Name: 4G Vehicle GPS Tracker,
Model: JM-VL01, GV40, VL01] is in compliance with the
essential requirements and other relevant provisions of
Directive 2014/53/EU.
The equipment was passed. The test was performed according
to the following European standards:
The full text of the EU declaration of conformity is available at
the internet address:
https://www.jimilab.com/JM-VL01-CE-DoC.pdf
The product shall only be connected to a USB interface of
version USB2.0 and that the connection to a power USB is
allowed.
This product is intended for sale and application in a business
environment.
RED Article 10 2
-This product can be used across EU member states
RED Article 10 10
-The product is class 1 product, No restrictions
The RF distance between body and product is 5mm
Maintenance or service arising from any other accessories
is not guaranteed.
Manufacturer assumes no responsibility for any damage caused
by non-original accessories.
Do not bend or open the battery.
Do not immerse or burn the battery.
Device dis-assembly is strongly forbidden.
Nonprofessionals’ operation may cause device damage.
11. Troubleshooting
If you are having trouble with your device, try these
troubleshooting procedures before contacting a service
professional.
Maintenance Record
Date
Serviced by
Product Model
IMEI Number
Fault
Descriptions
Comments
W
4. Repair or replacement under the terms of this warranty does
not provide right to extension or renewal of the warranty period.
5. The warranty is not applicable to cases other than defects in
material, design and workmanship.
2. Our obligations are limited to repair of the defect or replacement
the defective part or at its discretion replacement of the product
itself.
3. Warranty repairs must be carried out by our Authorized Service
Centre. Warranty cover will be void, even if a repair has been
attempted by any unauthorized service centre.
Unable to
connect to
the network
SIM card inserted
incorrectly
Check SIM card
Dirty things exist
above the SIM card
Clean SIM card
Invalid SIM card
Contact network
supplier
Not in GSM service
area
Move to service area
Poor signal
Move to area with
strong signal
Unable to
boot
Power switch is off Switch to ON
Battery low
No SIM card
charge
Insert SIM card
Problems
Causes Solutions
The signal waves are
unable to transmit
when use the GPS
tracker in the places
that have poor signal
reception, such as: tall
building around or
basement.
Using the GPS tracker
in the places that have
good signal condition.
Poor signal
Fail to locate
SIM has no access to
GPRS
Contact network
supplier to get GPRS
service
Always reply “Address
inquiry failed”
Contact supplier
Warranty instructions and service
1.The warranty is valid only when the warranty card is properly
completed, and upon presentation of the proof of purchase
consisting of original invoice indicating the date of purchase,
model and serial No.of the product. We reserve the right to
refuse warranty if this information has been removed or changed
after the original purchase of the product from the dealer。
User Manual
4G Vehicle GPS Tracker
(Version 1.0)
One side of the device is marked “ THIS SIDE
TOWARDS SKY”, place the unit upside down will
result in connection issues.
Avoid placing the device somewhere that metal will
be covering it up.
FCC RF Exposure Information and Statement
This device meets the government's requirements for
exposure to radio waves. The guidelines are based on
standards that were developed by independent scientific
organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons regardless
of age or health. The SAR limit of USA (FCC) is 1.6 W/kg
averaged. Device: 4G Vehicle GPS Tracker
(FCC ID: 2AMLF-JM-VL01) has also been tested against this
SAR limit. SAR information on this and other pad can be
viewed on‐line at http://www.fcc.gov/oet/ea/fccid/. Please
use the device FCC ID number for search. This device was
tested simulation typical 5mm body. To maintain compliance
with FCC RF exposure requirements, use accessories should
maintain a separation distance between the user's bodies
mentioned above, the use of belt clips, holsters and similar
accessories should not contain metallic components in its
assembly, the use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure
requirements, and should be avoided.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
NOTE 2: Any changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user's authority to operate the equipment.
GSM900: Tx: 880-915MHz, Rx: 925-960MHz
DCS1800: Tx: 1710-1785MHz, Rx: 1805-1880MHz
RF Output Power: GSM900: 31.30dBm, GSM1800: 25.39dBm
EDGE900: 30.30dBm, EDGE1800: 25.75dBm
WCDMA Band 1: Tx: 1920-1980MHz, Rx: 2110-2170MHz
WCDMA Band 8: Tx: 880-915MHz, Rx: 925-960MHz
WCDMA Band 1: 22.86dBm, WCDMA Band 8: 22.37dBm
FDD-LTE Band 1: Tx: 1920-1980MHz, Rx: 2110-2170MHz
FDD-LTE Band 3: Tx: 1710-1785MHz, Rx: 1805-1880MHz
FDD-LTE Band 7: Tx: 2500-2570MHz, Rx: 2620-2690MHz
FDD-LTE Band 8: Tx: 880-915MHz, Rx: 925-960MHz
FDD-LTE Band 1: 23.50dBm, FDD-LTE Band 3: 22.98dBm,
FDD-LTE Band 7: 24.11dBm, FDD-LTE Band 8: 22.56dBm
Wi-Fi:
2412-2472MHz for 802.11b/g/n(HT20)
2422-2462MHz for 802.11n(HT40)
14.16dBm (EIRP)
GPS
Frequency Range: 1575.42MHz receiver