'× ' Tool Storage Shed ASSEMBLY MANUAL MODEL#: LGCF1552
118 . 4 3″ 3008 mm 1164 (45. 8") 111. 42″ 2830 m m 1552 76.5 7″ 1 9 4 5 mm 1 5 8 4 (62.4 " ) ″ 12 mm . 95 416 2 ″ 73 mm .
Themanualwi l lassi styoudur i ngt hewhol epr ocessofassembl i ng. Makesur eyouhav eal lt hepar t s& har dwar easl i st1andl i st2shown; pr epar et hel ev elgr oundf ori nst al l at i on.
List-1
Hexagonal Socket Wrench Hand Gloves List-2 Hole Position Correction Drill Cross Screwdriver
1# x48 1.Firstly, use the part#A7 to connect part#A1(A4/A5) with part#A2(A3/A6)respectively, and then form the bottom frame as shown.
Step 1: Use 6 screws 9#, gaskets and caps to connect 2 part H2 with part #C/J/J/C1 as shown in O to form a front side wall panel. Step 2: Place the assembled front side wall panel (#C/J/J/C1) on the bottom frame(A1), using 7 screws 1# and gaskets to fix.
Step 3: Place part#J on the bottom frame(A6), using 3 screws 1# and gaskets to fix. Repeat the above procedures to assemble the another side. Step 4: Fix the part #C3 to the part #C1(C2) with 2 screws 3#, 2 gaskets and nuts each as shown in ③④. Attention:To ensure the stability of the wall panel(J) during assembly, you can temporarily reinforce this position(☆) with screws 2#, and replace it with other correct screws when the next installation is made.
05
Step 1: Place part #J/C/J1 on the bottom frame(A6&A4), using 7 screws 1# and gaskets to fix. Step 2: Use 4 screws 9# and gaskets to install 2 part#（H5+H6）with part#C & J, then put on the plastic caps as shown in ①/③. Repeat the above procedures to assemble the another side as shown in ②④ Step 3: Use 4 screws 9# and gaskets to installe 2 part#（H4+H3）with part#C & J1, then put on the plastic caps as shown in ③/④.
Step 1: Use 13 screws 1# and gaskets to fix 4 part#J on the bottom frame（A5 & A6） Step 2: Use 10 screws 9# and gaskets to fix 4 part#J with 2 part#（H5+H6), then put on the plastic caps to form a whole side wall as shown in ①②. Repeat the above procedures to assemble another side wall. Step 3: Use 15 screws 1# and gaskets to fix part#J1&J&J&J1 on the bottom frame（A4 & A3）.
08
09
Place the assembled beam (B1,B2, B3,B4,B5,B6) on the upper end of the wall panel, and fix with 75 screws 1# and gaskets as shown in ①②. Fix the upper end of the part#C1/C2 with part#B1 and part#C4 by using screws 3#, the nuts and gaskets are on the back side as shown in ③④.
11
Use 2# screws (including 1 screws 1 gaskets and 1 nuts) to fix part#E3/E4 with part#D3/D4 as shown in ②③. Top frame assembly: Splice the part#D1/D2, clamp the two sides of the part#E1/E2 and part#D, and tighten with the screws 3# (including 1 screws 2 gaskets and 1 nuts) as shown in ①.
Cross Screwdriver Put the top frame on beam(#B1 & #B2 & #B3 & #B4), use 24 screws and gaskets #1 to fix.
X2 Assemble the part#G2 to the one side of part#K5 with 5 screws 2# gaskets and nuts. Assemble the part#G1 to the one side of part#K1 with 5 screws 2# gaskets and nuts.
Attention: The top plate can be installed in order or reverse order. If there is a deviation between the top plate and the top frame installation hole, it is generally caused by the diagonal size deviation of the frame beam. The diagonal distance of the frame beam can be measured and adjusted.
Part #Z shall be inserted at the fixed position of top beam and top roof groove to prevent rainwater intrusion. Plastic Cap The roof panel K1/K5 is fixed with top frame D1/D2 by using screws 2#.gaskets and nuts as shown in ③; then fix with screw1# and gaskets to side frame beam as shown in ④. D1 D2 The top plate is fixed to the side frame beam.
Part #Z shall be inserted at the fixed position of top beam and top roof groove to prevent rainwater intrusion. Plastic Cap Fix the roof panel K4/K3/K2 by using screws 2#. gaskets and nuts as shown in ②, then fix with screw 1# and gaskets to side frame beam as shown in ④. ④ ④ D1 Plastic Cap 17 Secure the top plate to the top beam with self-tapping screw 4# and part #Z.
D1 Step1: Install the part #F: Insert part #Z into the top panel groove, use 4 screws 11#, gaskets and nuts to fix part#F2 and part #F on the roof top. (part #F should cover on part#F2) as shown in ②. 18 D2 Step2: Use 4 screws 3#,gaskets and nuts to fix the 2 sides of part #F with part #K1/K5 and part #D1/D2 as shown in ①.
Step1: Use 18 screws 2# gaskets and nuts to fix part #G3 and part#G4 on the cornice of top roof. Use 4 screws 2#,gaskets and nuts to cover part #G7 on the connection of part #G3 and part#G4 as shown in ③. Repeat the above producers to assemble the another side.
Install the part #G5/G6 with 8 screws 3#, gaskets and nuts as shown in ①/②. Use 4 screws 7# to install the part #F1 from the inside. Repeat the above procedure to assemble the another side.
How to Install the Door There is a bolt on the left door This section is installed by the user. There is a handle on the right door The hinge has been pre-installed on the door frame C1/C2 by the factory. Lining board Y is on the inside of the door frame.
Insert the bolt and lock the left door. Open the door: insert the key, rotate 180 counterclockwise, and rotate the handle counterclockwise to open the door. Lock the door: close the door, insert the key, rotate the handle clockwise, then rotate the key 180 clockwise and pull the key out. Insert the bolt and lock the left door.
