1'×9' Tool Storage Shed ASSEMBLY INSTRUCTIONS MODEL#: LGCF1620 Missing part? Damaged? Contact us via email at service@domioutdoorliving.com www.domioutdoorliving.com © Copyright 2022-2024 domi LLC. I All Rights Reserved.
List-1
List-2
Cross Screwdriver Gloves List-3 Hexagonal Socket Wrench Hole Position Correction Drill
1# x48 ①:Use part#A7 to connect the bottom frame respectively, and then fix with bolt #1 and gaskets as shown.
# x4 1# x16 Plastic Gaskets Plastic Gaskets C3 x2 ①:Insert part #A to the corners. ②:Fix with 4 bolts #1 & gaskets. ② ① ③ ③:You need to prepare bolts by yourself to secure the frame to the ground. ⑤ ④ ④/⑤: Fix 2 part#C3 on part #A1, part #A2 by using 4 bolts 9# and gaskets.
12# x24 Top Frame Assembly ①：Connect part #B1 & #B2, insert part #B7 & #B8 on the inside of part #B1/B2 with 6 bolts 12# and gaskets. ②: Connect part #B3 & #B4, insert part #B7 on the inside of part #B3/B4 with 6 bolts 12# and gaskets. ③: Connect part #B5 & #B6, insert part #B7 with 6 bolts 12# and gaskets.
C4 x2 9# x4 12# x16 Plastic Gaskets Plastic Gaskets ①/②: Use #part #B to connect part #B5 & #B3, part #B4 & #B6, part #B5 & #B2, part #B1 & #B6, fix with 16 bolts 12# and gaskets. ① ③ ② ④ ③/④: Fix 2 part #C4 on part #B1, part #B2 by 4 bolts 9# and gaskets. ! 04 You can also install each top frame on each wall separately.
Section View ①: Use 10 bolts 9#, gaskets and caps to connect 2 part #H2 with part #C/J1/J1/C1 to form a front side wall panel. Section View ②: Use 10 bolts 9#, gaskets and caps to connect 2 part #H1 with part #C2/J1/J1/C to form a front side wall panel. Place the assembled front side wall panel (#C/J1/J1/C1) on the bottom frame(#A1), using 9 bolts 1# and gaskets to fix. Place the assembled front side wall panel (#C2/J1/J1/C) on the bottom frame(#A2), using 9 bolts 1# and gaskets to fix.
Section View Section View Place part #J on the bottom frame(#A6), using 3 bolts 1# and gaskets to fix. ! Attention: To ensure the stability of the wall panel(#J) during assembly, you can temporarily reinforce this position(☆) with bolts 2#, and replace it with other correct bolts when the next installation is made. Repeat the above procedures to assemble the other side. Inside View Inside View ③: Fix part #C3 to part #C1 with 2 bolts 3#, 4 gaskets and 2 nuts.
H6 Use part #H7 to connect part #H3 and part #H4, and fix with bolts 3#, gaskets and nuts. Repeat the above procedures to connect part #H5 with part #H6.
Inside View Outside View Side Window Assembly: Insert part #N to the wall panel #J2 (from outside to inside), place transparent board #N2, use 8 bolts #13 to fix part #N1 & part #N (from inside to outside). Repeat the above procedures to assemble another side window.
1# x12 9# x8 Place part #J2/J/C on the bottom frame #A6, using 6 bolts 1# and gaskets to fix. ①: Use 2 bolts 9# and gaskets to install 2 support tubes(H6+H5) to wall panel #J, then put on the plastic caps. Front Side Back Side Side View ⑤: Use 2 bolts 9# and gaskets to install 2 support tubes(H6+H5) to wall panel #J2, then put on the plastic caps. Plastic Cap 09 Repeat the above procedures to assemble another side.
1# x8 9# x12 Place part #J1 on the bottom frame #A4, using 4 bolts 1# and gaskets to fix. Place part #J1 on the bottom frame #A3, using 4 bolts 1# and gaskets to fix. Front Side Back Side Section View Plastic Cap ③: Use 4 bolts 9# and gaskets to install 2 support tubes(H6+H5) & 2 support tubes(H4+H3) to part #C, then put on the plastic caps. ⑤: Use 4 bolts 9# and gaskets to install 2 support tubes(H4+H3) to 2 wall panel #J1, then put on the plastic caps.
Side View Side View Plastic Cap Plastic Cap Use 13 bolts 1# and gaskets to fix 4 part #J on the bottom frame(A5 & A6). ①: Use 10 bolts 9# and gaskets to fix 4 part #J with 2 support tubes(H5+H6) , then put on the plastic caps to form a whole side wall. Repeat the above procedures to assemble another side wall. Use 19 bolts 1# and gaskets to fix 6 part #J on the bottom frame(A4 & A3).
①/②: Place the assembled frame on the upper end of the wall panel, and fix with 89 bolts 1# and gaskets. ③: Fix the upper end of the part#C1 with part #C4(already assembled on part#B1) by using bolts 3#, the gaskets and nuts are on the back side. Inside View 12 ④: Fix the upper end of the part#C2 with part #C4 (already assembled on part#B2) by using bolts 3#, the gaskets and nuts are on the back side.
Connection of the middle top beam (part #E1*2/E2*2/E5*2/E6*1) Plastic Cap Section View Connection of the side top beam (part #E3/E4/E5) X2 Plastic Cap Section View 13
Top Beam Assembly ①: Splice part#D1 & #D2, clamp the 2 sides with part #D; Use 3 bolts 3# (including 1 bolt ,2 gaskets and 1 nuts) to fix 2 part #D to part #D1 & #D2; Clamp the two sides with part#E1/E2, and tighten with 2 bolts 3#, gaskets nuts. Repeat the above procedures to assemble another side.
②: Use 4 bolts 2#(including 1 bolt,1 gaskets and 1 nuts) to fix part #D3 with part #E4 & #D1. ③: Use 4 bolts 2#(including 1 bolt,1 gaskets and 1 nuts) to fix part #D4 with part #E3 & #D2. Repeat the above procedures to assemble another side.
Cross Screwdriver Place the assembled top beam on the top frame, tighten with 28 bolts #1 and gaskets.
Assemble part #G2 to the one side of part #K2 with 6 bolts 2# gaskets and nuts. X2 Assemble part #G1 to the one side of part #K1 with 6 bolts 2# gaskets and nuts.
Attention: The top plate can be installed in order or reverse order. If there is a deviation between the top plate and the top frame installation hole, it is generally caused by the diagonal size deviation of the frame beam. The diagonal distance of the frame beam can be measured and adjusted.
Plastic Cap Plastic Cap ①: Secure the roof panel to the main top beam with 42 self-tapping bolts 4# and part #Z. ②: Part #Z shall be inserted at the gap between roof panels and side top beam, then fix with 20 self-tapping bolts #5 and caps to prevent rainwater intrusion.
③: The roof panel K1/K2 is fixed with top frame D1/D2 by using 20 bolts 2#, gaskets and nuts. ④: The roof panel is fixed to the side top frame (B5,B6) by using 42 self-tapping bolts #1 and gaskets.
①: Use 2 bolts 3#, 4 gaskets and 2 nuts to fix part #F with part #K1/K2 and part #D1/D2. Use 2 bolts 3#, 4 gaskets and 2 nuts to fix part #F3 with part #K1/K2 and part #D1/D2. Section View ②: Insert part #Z into the roof panel groove, use 4 bolts 11#, 8 gaskets and 4 nuts to fix part #F2 and part #F/#F3 to the roof top. (part #F/#F3 should cover on part#F2).
③: Step.1: Use 21 bolts 2# gaskets and nuts to fix part #G3 and #G4 on the cornice of roof panel. Step.2:Use 4 bolts 2#,gaskets and nuts to cover part #G7 on the connection of part #G3 & #G4. Repeat the above producers to assemble another side.
①/②: Install part #G5/G6 to 4 corners of the roof, fix with 8 bolts #3, 16 gaskets and 8 nuts. ③: Use 4 bolts 7# to install part #F1 from inside. Repeat the above procedure to assemble another side.
The front side of left door Installation diagram of door panel, frame and screw The back side of left door Section View
The back side of right door Installation diagram of door panel, frame and screw The front side of right door Section View
There is a latch on the left door There is a handle on the right door ①: This section is need to installed by the user. Lining board #Y is on the inside of the door frame. 24 The hinge has been pre-installed on the door frame C1/C2 by our factory.
①/②: Insert the latch and lock the left door. ③: Open the door: insert the key, rotate 180 counterclockwise, and rotate the handle counterclockwise to open the door. Lock the door: close the door, insert the key, rotate the handle clockwise, then rotate the key 180 clockwise and pull the key out.
