BlueSet ™ Wireless Headset Interface User Guide JK Audio
Welcome Thank You Thank you for purchasing the JK Audio BlueSet Wireless Headset Interface. Please read this guide for instructions on setting up and using your new product. Getting Assistance If you have technical or application questions: In the US & Canada, call us toll free at: 800-552-8346 All other countries dial: 815-786-2929 (M-F 8:30-5:00pm Central Time Zone) Email us at: support@jkaudio.com Or, check out our FAQ section for answers to common questions.
Contents Overview 1 Getting to know your BlueSet 2 Starting Up 3 Bluetooth Wireless Technology 4 FAQ's 9 Technical Information 16 4 5 6 7 Status LED Pairing to a Cell Phone Pairing to a Headset Disconnecting, Connection History, Reconnecting Contents iii
Features HD Voice* Trim Pot adjusts Bluetooth Return Electret / Dynamic Headset Compatibility Mini USB Power Jack 1/8" (3.5 mm) Mic Level Output >10 Hours on Internal Li-Ion Battery * HD Voice. While standard phone calls have a narrow bandwidth of 300 Hz to 3.4 kHz, HD Voice calls offer 50 Hz to 7 kHz bandwidth. The additional 1.5 octaves on the low end gives voice a more natural sound, while the additional upper octave dramatically improves speech clarity and intelligibility. Wireless HD Calls.
Overview Introducing the BlueSet. These headset interfaces plug directly into most Party- Line (PL) belt packs, replacing the wired headset. A 3.5 mm stereo headset jack contains a mic level output signal suitable for recording, with the beltpack headphone signal on the left channel, and the Bluetooth return signal on the right. A switch selects between connection to a 3rd party Bluetooth headset or a cell phone. Headset Connect: Leave your belt pack on the desk as you walk around the room.
Getting To Know your BlueSet Mode Switch In the Bluetooth world, a Master device, such as a wireless phone, computer, or music player, is connected to a Headset device. Before you turn the BlueSet on, be sure to set the to the correct position. If you change that switch while the unit is on, you will need to power the unit off, then power the unit back on before the change takes effect.
Starting Up Charging To achieve maximum battery capacity, BlueSet should be fully charged before its first use. While this battery will normally charge in about 2 1/2 hours, please allow 4-5 hours for this first charge. Connect the power supply cable to the mini USB connector on your BlueSet to charge the battery. The red LED will flash to indicate that the battery is charging, once charging is complete, the LED will turn off.
Bluetooth Wireless Technology Bluetooth Status LED The blue LED on the side of the unit flashes in different sequences to indicate the current connection status. Pairing Mode In Pairing Mode, any Bluetooth wireless technlogy enabled device within range can pair with your BlueSet. To put the unit in Pairing Mode, press the for 6 seconds. The blue LED will flash rapidly at a rate of 100ms off, 100ms on.
Bluetooth Wireless Technology Pairing to a Cell Phone with Bluetooth Wireless Technology When you're first connecting to a new device, you should be in an environment with no other Bluetooth wireless technology enabled devices within range that might also be in Pairing Mode. 1. Set the to the position. 2. From the powered-off state*, hold the on the BlueSet for at least 6 seconds.
Bluetooth Wireless Technology Pairing to a Headset with Bluetooth Wireless Technology When you're first connecting to a new device, you should be in an environment with no other Bluetooth wireless technology enabled devices within range that might also be in Pairing Mode. 1. Set the to the position. 2. Following manufacturer’s instructions, set your headset to Pairing Mode. Note: Connecting via Bluetooth wireless technology varies with different cell phones.
Bluetooth Wireless Technology When Should I Release the MFB Button? Idle Mode Pairing Mode Bluetooth LED Role Change Clear seconds Disconnecting from a Device To disconnect from any Bluetooth wireless technology enabled device and turn the power off, simply hold the until the blue LED turns off (approx. 5 seconds). Connection History BlueSet rretains a history of the 16 most recent devices.
Wireless Applications Master(Phone) or Headset Mode The Master device controls the connection, and also has the ability to stream stereo A2DP audio to the Headset device. A2DP music streaming is a oneway path from Master(Phone) to Headset. BlueSet can act as either a Master or Headset. Please note that wireless phones typically cannot receive A2DP stereo music streaming. BlueSet will first attempt to connect using the Hands-Free profile, allowing 3.
FAQ's What is the range of the transmitter/receiver? BlueSet transmits and receives audio signals up to 50 feet from your Bluetooth wireless technology enabled device. The maximum range of this product is achieved when a clear line of sight is maintained between connected devices, but may also be limited by interference due to the environment. While this product offers extended range capabilities, maximum usable range is limited by the weaker of the two paired/connected devices.
FAQ's What kind of intercom headset jack is BlueSet compatible with? BlueSet can be used to replace an electret or dynamic intercom headset. Why doesn’t the BlueSet change connections when I move the switch from Headset to Phone? If you change this switch while the unit is on, you will need to power the unit off (see page 7), then power the unit back on before the change takes effect. How long does it take to recharge the battery? BlueSet can fully charge the internal battery in about 2 1/2 hours.
Technical Information Battery Information BlueSet contains a rechargeable Lithium-Ion battery. These batteries do not have a “charging memory” and can be recharged at any time without changing their life expectancy. All rechargeable batteries have a limited life and will gradually lose their capacity to hold a charge. This loss of capacity is irreversible. To get the most from your BlueSet, the battery should not be allowed to fully discharge.
Technical Information Output Misc Connection: 1/8" (3.5 mm) stereo Impedance: 1000 ohms Level: 15 mV RMS; -34 dBu nom. Bluetooth Standard: Bluetooth 3.0 Distance: 50 feet ( 15 meters ) Frequency Response: HF = full duplex voice 300 Hz - 3.4 kHz HF (HD) = full duplex HD Voice 50 Hz -7 kHz Power Supply: 120-240 VAC 5V DC, 50 ma Connector: Mini-USB Series B Battery: Internal Lithium-Ion Polymer rechargeable Dimensions Size: 1.1” x 4.4” (2.8 cm x 11.2 cm) Weight: 2.
FCC-B Part 15 Compliance FCC-B Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Declaration of Conformity Manufacturer’s Name: JK Audio, Inc. Manufacturer’s Address: 1311 E 6th Street Sandwich, Illinois 60548 USA Declares that the product: Product Name: Model Numbers: BlueSet™ Wireless Headset Interface BlueSet-F4, BlueSet-M4, BlueSet-F5, BlueSet-M5 Conforms to the following Product Specifications: 14 Safety: AS/NZS 60950.1:2003 CAN/CSA-C22.2 No.
Declaration of Conformity The product herewith complies with the requirements of the following Directives and carries the CE marking accordingly: LVD 2006/95/EC (Safety) EMC 04/108/EEC (EMC) RoHS Directive 2002/95/EC The Technical File containing supporting documentation is maintained at: JK Audio, Inc (Corporate Headquarters) Compliance Manager 1311 E 6th Street Sandwich, Illinois 60548 USA +1-815-786-2929 phone +1-815-786-8502 fax Declaration of Conformity 15
BlueSet™ Wireless Audio Interface User Guide Version 7/29/14 JK Audio, Inc. 1311 E 6th St. Sandwich, IL 60548 United States Telephone: 815.786.2929 Toll Free: 1.800.jkaudio Fax: 815.786.8502 www.jkaudio.com © 2014 JK Audio, Inc. All rights reserved. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by JK Audio, Inc. is under license.
