User guide

ManualsBrandsJKS ManualsCar9901

JKS part numberJKS DESCRIPTION Installation

Page 1

INSTALLATION

INSTRUCTIONS

Product: B1 Body Lift

Part Number: JKS9901

Applications: CJ8, 1978-82

Welcome

Congratulations on purchasing a new B1 Body Lift from

JKS® Manufacturing. We are committed to providing you

with the best products available and your satisfaction is our

rst priority.

We hope you enjoy your JKS® purchase and are here to

help if you still have questions after reviewing this safety

information and instructions. Contact us online at www.

jksmfg.com or by phone at 877-533-7557.

Tools Required

 Metric/Standard Socket Wrench Set

 Torque Wrench

 Tape Measure

 Medium Strength Threadlocker

 Hydraulic Floor Jack

 Sturdy Block of Wood (to protect body)

 Center Punch and Hammer

 3/8” Drill Bit

 1/8” Drill Bit or Torch * (for removing plastic rivets

in steering slip shaft)

 Reciprocating Saw or Die Grinder with Cut-Off Wheel *

(for trimming fan shroud)

 Wire Brush *

 Factory Service Manual (recommended)

* Asterisk denotes tools that are not required for some applica-

tions. Thoroughly read instructions rst to determine which tools

will be required for your application.

CAUTION

Always Wear Protective Gear

Safety glasses and protective gloves are required.

Parts

Description QTY

Dura-Thane™ Body Puck 13

3/8” x 3-1/2” Bolt 8

3/8” x 4” Bolt 2

3/8” Flat Washer 10

7/16” x 4” Bolt 3

7/16” Flat Washer 3

NOTICE

One Side At A Time

Body lift must be installed on one side of vehicle at a time.

517-278-1226 • tech@jksmfg.com • www.jksmfg.com

491 W. Gareld Avenue, Coldwater, MI 49036

Summary of content (4 pages)

PAGE 1
Product: B1 Body Lift Part Number: JKS9901 INSTALLATION INSTRUCTIONS Applications: CJ8, 1978-82 517-278-1226 • tech@jksmfg.com • www.jksmfg.com 491 W. Garfield Avenue, Coldwater, MI 49036 Welcome Parts Congratulations on purchasing a new B1 Body Lift from JKS® Manufacturing. We are committed to providing you with the best products available and your satisfaction is our first priority.
PAGE 2
To reduce risk of serious injury and accident: Important Product Safety Information ÂÂ Choose modifications that balance your actual highway & off-road use. For your safety and the safety of others, please read all instructions and warnings in this pamphlet and your Jeep® owner’s manual and off road driving supplement before attempting installation.
PAGE 3
Carefully raise the vehicle body just enough to insert 1.25” Body Pucks (A) between body and factory body mounts 2 3 4 5 6 and 7. NOTE: Recessed bottom of Body Pucks must encapsulate factory body mounts. With Body Pucks (A) inserted, slowly lower the vehicle body onto mounts, ensuring correct alignment of body on chassis. Apply medium strength thread locking compound to four of the supplied 3/8” x 3-1/2” Bolts (B), one of the 3/8” x 4” Bolts (C), and one of the 7/16” x 4” Bolts (E).
PAGE 4
5. CHECK T-CASE OPERATION Check operation of the shift lever to ensure the transfer case fully engages all ranges. NOTE: If necessary, adjust linkage between shift lever and bell crank. If interference is experienced, it may be necessary to trim the floor to provide sufficient shift lever clearance. 6. CHECK FOR STEERING BIND Drive vehicle a short distance while checking for binding in the steering wheel. If no steering bind exists, skip this section and proceed to step 7.