Manual

Installation Instructions for all
PS-SWMCP
swivel fixtures for round pipes
PIPE MOUNTING FIXTURES (SWIVEL)
FOR PS650Ve X™ ENCLOSED SPEAKER SYSTEMS
NOTE: The PS-SWMCP-B-2.000 Fixture and PS650-VeX-SG-TMB Enclosed Speaker
System are used in this manual for illustrative purposes only. The fixture installation
steps are the same for all PS650-VeX Enclosed Speaker Systems and all PS-SWMCP
swivel fixtures for round pipes.
LIMITED WARRANTY  MARINE PRODUCTS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the
original date of purchase.
This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service
be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),
repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not
covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning
with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Service Information in the U.S.A. please call
JL Audio Customer Service: (954) 4 43 -110 0
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
w w w . j l a u d i o . c o m
JL Audio® and the JL Audio logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
©2016 JLAudio, Inc. • For more detailed information please visit us online at www.jlaudio.com. Due to our policy of continuous product development, all specifications are subject to change without notice.
SKU# 011498
Printed in U.S.A. • 092817
Mounting Fixture is made in the USA by Axia Alloys
Protected by US Patents #8,136,771 & #8,398,035
Included Hardware:
BOM ID Quantity Description
1 4 Axia Alloys Strap Clamp
2 6
M6 x 16 mm Socket Cap Machine Screw
3 2 M4 x 4 mm Set Screw (pre-installed)
4 4 M6 Nylon Insert Locknut
5 2 Clamp Receiver
6 1 Loctite® Red read-Locking Compound
7 4 M6 Flat Washer
8 4 M6 x 45 mm Socket Cap Machine Screw
9 1 Plastic Strip
10* 2 Fixture Base
11* 1 Silicone Adhesive
12* 12 #8 Flat Washer
13* 12 #8 x 1-1/4” Pan Head Screw
* Included with VeX™ speaker enclosures.
(hardware pictured for one)
Note: Not all wires may be used in normal applications.
Wire Size Wire Color Use
16 AWG
Red/Stripe Speaker Positive (+)
Black/Stripe
Speaker Negative (–)
20 AWG
Red Not Used
Green Not Used
Blue LED Positive (+)
Yellow LED Negative (–)
Wire Size Wire Label Use
16 AWG
“+”
Speaker Positive (+)
N/A
Speaker Negative (–)
For Premium Models:
For Standard Models: