Manual

Loosen the pre-installed M4 x 4 mm Set Screw in the
clamp receiver. Slide an M6 x 16 mm Machine Screw
through the center hole of the clamp receiver, into the
center hole in the xture base, and hand tighten.
1
If you wish to rotate the speaker’s grille/logo badge
alignment, remove the six #8 x 1-1/4” speaker mounting
screws and #8 Flat Washers.
9
Apply Loctite® red thread-locking compound to two M6
x 16 mm Machine Screws, slide them through the slots
in the clamp receiver, into the appropriate holes in the
xture base, and fully tighten.
5
Secure the clamps to the clamp receiver using a pair of
M6 x 45 mm Machine Screws, M6 Flat Washers, and M6
Locknuts as illustrated. e locknut should be installed
into the hex shaped recess on one end of each clamp.
Hand-tighten, allowing just enough freedom to rotate the
enclosure around the pipe.
3
Realign the clamps with the clamp receiver on the
enclosure, and secure them to the clamp receiver using a
pair of M6 x 45 mm Machine Screws, M6 Flat Washers,
and M6 Locknuts as illustrated, and fully tighten. Note:
e locknut should be installed into the hex shaped
recess on one end of each clamp.
7
Place the supplied plastic strip around the pipe to
prevent scratching. Push the clamps over the pipe
(remove the plastic strip). Align the clamps with the
clamp receiver on the enclosure.
2
Remove the center M6 x 16 mm Machine Screw from the
clamp receiver, apply Loctite® red thread-locking
compound, reinstall, and fully tighten.
6
Position the enclosure at the desired location, tightening
the M6 x 45 mm Machine Screws as necessary. Fully
tighten the pre-installed M4 x 4 mm Set Screw in the
clamp receiver to hold its position. Mark the location
of the clamps on the pipe, then remove the enclosure
from the pipe.
4
Rotate the speaker to the desired angle. Reinstall the
speaker and speaker mounting screws and washers.
Hand-tighten in a criss-cross pattern.
10
Remove adhesive backing and install the JL Audio logo
badge.
8
Remove the backing from the rear logo appliqué. With
the logo positioned at the desired angle, attach the
appliqué to the back of the enclosure.
11
Gently press on the appliqué from the center out to
remove any air pockets.
12
Clean the inside of the aluminum cap with acetone (not
included) prior to attaching it to the enclosure. Apply a
circular bead of silicone adhesive to the inside of the
aluminum logo cap, 1/2-inch (13 mm) from the outer edge.
13
Align the aluminum logo cap to the desired angle of
rotation, and press it onto the back of the enclosure.
Apply masking tape (not included) to hold the cap in
place until the silicone cures (at least 24 hours).
14
• For marine installations, do not connect the speaker’s LED lights to the vessel’s navigational lighting circuits.
• For short-circuit protection, install a supplied fuseholder onto EACH speaker’s BLUE (+12V) LED power connection lead.
• Connect all BLUE (+12V) leads together (parallel) and connect to a switched +12V supply. Connect all YELLOW (GND)
leads together and connect to a negative ground or to the NEGATIVE battery post.
• We recommend activating the speakers’ LEDs thru a lighting circuit that supplies +12V via an existing switch. If an
existing switched circuit is not available, you may install a dedicated toggle/rocker style switch that will supply positive
(+12V) power. Fuse this connection according to how many LED circuits you have (LED circuits x 150 mA).
[GND]
LED
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
Fuse
Fuse
Fuse
[GND]
[+12V]
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
LED
LED
LED
LED
Fuse
Fuse
Fuse
Fuse
Fuse
Example: One speaker pair of
LED circuits connected in parallel.
Steps 11-12 are for Standard Models Only
Steps 13-14 are for Premium Models Only