Manual

2-Year Limited Warranty (U.S.A.)
Visit www.jlaudio.com for warranty details.
For Service Information in the U.S.A. please call JL Audio customer
service: [phone] during normal business hours (Eastern Time)
JL Audio, Inc • 10369 N Commerce Parkway, Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are covered
only by that country’s distributor and not by JL Audio, Inc.
SKU# 011476 12-14-2016
Replacing the Battery
1. Remove the four screws from
the back of the remote.
2. Gently separate the front half
of the remote.
3. Lift and remove the
silicone keypad from
inside the remote.
4. Turn the remote over to
remove the circuit board.
The battery is installed on
the back of the circuit board.
5. Carefully remove the battery
from its holder and replace
with a CR2032 style battery
or equivalent.
6. Reassemble the remote to
ensure a watertight seal.
Receiver Module Programming
Note: The transmitter and receiver included with the MMR-10W
system are already paired.
Up to ten (10) MMR-10W Remote transmitters may be paired to a
single receiver module.
To Pair A New Transmitter (Required for MMR-10W-Remote)
1. Disconnect +12V power from your MediaMaster® by removing the
5-amp fuse from its fuse holder, unplugging its 4-pin power plug,
or switching o its +12V supply circuit.
2. Press and hold both and buttons on the transmitter, then
reconnect +12V power to your MediaMaster®.
3. Continue holding both and buttons for 5 to 10 seconds,
then release both buttons.
• If successful, the status LED will emit two quick ashes with any
button press.
• If unsuccessful, the status LED will emit two long ashes with any
button press.
4. Repeat steps 1 to 4 to pair additional transmitters (up to ten total).
LED Signal Conrmation
The MMR-10W transmitter is equipped with a red LED mounted
beneath the MUTE button.
The LED will ash once when any button is pressed, and then a second
time when the button is released to verify that the remote’s transmit-
ted signal was successfully received by the receiver module.
• Two short ashes indicate the signal was sent/received successfully.
• Two long ashes indicate the signal was sent, but not successfully
received. Possible failure causes include low battery level, out of
operating range, or the receiver module is not active (MediaMaster®
is turned OFF).
Remote Control Functions
Below is a list of MMR-10W command functions. The functionality
of some controls will vary depending on the current source and/or
last tuner selected. Note: The MediaMaster® source unit only accepts
commands from the MMR-10W when its display is on a Now Playing
Screen or in the SOURCE: Select menu screen:
PWR
• Press to turn the source unit ON
• Press and hold for two seconds to turn the source unit OFF
SRC
• Press to turn the source unit ON
• Press to cycle through sources (Last tuner/USB/Bluetooth®/AUX)
VOL+
• Press to increase volume
VOL–
• Press to decrease volume
MUTE
or
• Press to mute/unmute audio (AM/FM/WB/SiriusXM®/AUX)
• Press to pause/resume the current selection (USB/Bluetooth®)
• Press to select the next Favorite (AM/FM/WB/SiriusXM®)
• Press to select the next track (USB/Bluetooth®)
• Press and hold to fast-forward (USB)
• Press to select the previous Favorite (AM/FM/WB/SiriusXM®)
• Press to select the previous track (USB/Bluetooth®)
• Press and hold to fast-rewind (USB)
Specications
Operating Frequency 2.4 GHz
Operating Range* Up to 150 ft. (45 m)
Operating Temperature -4 °F to +167 °F (-20 °C to +75 °C)
IP Rating (Transmitter) IP67
IP Rating (Receiver) IP65
Dimensions
(Transmitter)
2.99 in x 2 in x 1.07 in
76 mm x 50.8 mm x 27.2 mm
Dimensions
(Receiver)
4.02 in x 3.01 in x 1.42 in
102.1 mm x 76.5 mm x 36.1 mm
* Maximum operating range will vary based on installation specics and
transmitter battery level.
Steering Wheel Mount Example
Attach to a steering wheel using the
included plastic cable ties.
In case of misplaced transmitters, you may delete all remotes from the
receiver module’s memory.
Note: All paired transmitters will stop working after deletion.
Subsequent remote functionality will require each transmitter to be
paired with the receiver.
To Delete All Transmitters
1. Disconnect +12V power from your MediaMaster® by removing the
5-amp fuse from its fuse holder, unplugging its 4-pin power plug,
or switching o its +12V supply circuit.
2. Press and hold both
VOL+ and VOL– buttons on an
existing (paired) transmitter, then reconnect +12V power to
your MediaMaster®.
3. Continue holding both
VOL+ and VOL– buttons for 5 to 10
seconds, then release both buttons.
• If successful, the status LED will emit two long ashes with any
button press and the transmitter will no longer control your
MediaMaster®.
• If unsuccessful, the status LED will emit two quick ashes with
any button press and the transmitter will still control your
MediaMaster®.