Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
3120870 3-15
SECTION 3 BOOM
S
E
C
T
I
O
N
3
B
O
O
M
.
FIGURE 3-4. MAIN BOOM ASSEMBLIES
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.
MAIN BOOM ASSEMBLY OPTIONS:
0801131 450A Ref. D
0801148 450AJ Ref. D
1 0100011 Loctite #242 (Not Shown) A/R
2 0560923 Block, Tube Support 1
3 0641404 Bolt 1/4”-20NC x 1/2” 8
4 0641606 Bolt 3/8”-16NC x 3/4” 8
5 0641607 Bolt 3/8”-16NC x 7/8” 14
6 0641608 Bolt 3/8”-16NC x 1” 6
7 Base Weldment Options: 1
0801129 450A
0801146 450AJ
8 Fly Weldment Options: 1
Use 0801170 450A Prior to S/N37903 (was p/n 0801130)
0801170 450A S/N37903 to Present
0801147 450AJ
9 0961950 Bushing, Garmax 4
10 Not Used
11 3311401 Nut 1/4”-20NC 2
12 3311605 Locknut 3/8”-16NC 4
13 3340756 Pad, Wear 9
14 3340836 Pad, Wear 2
15 3340837 Pad, Wear 2
16 3422705 Pin 1
17 Pin Options: 1
3422706 Prior to S/N37743
3422745 S/N37743 to Present
18 3570869 Cover, Boom End 1
19 3760115 Ring, Retaining 2
20 3760133 Ring, Retaining 2
21 4070559 Shim A/R
22 4070898 Shim A/R
23 4751400 Flatwasher 1/4” 10
24 4751600 Flatwasher 3/8” 4
25 4761400 Lockwasher 1/4” 10
26 4761600 Lockwasher 3/8” 6
27 Cover, Hose 1
4845767 450A
4845696 450AJ
28 1180227 Powertrack 1
7006152 Kit, Pin (1 pin, 4 Different Size Washers & 1 Retaining
Ring)
1
7006151 Feet Mounting 1
7006139 1ft. Section 1
7006156 Rod, Carrier 1