Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
3120870 4-3
SECTION 4 PLATFORM
S
E
C
T
I
O
N
4
P
L
A
T
F
O
R
M
FIGURE 4-1. PLATFORM INSTALLATION
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.
PLATFORM ASSEMBLIES:
3510632 48in x 30in (1.22m x .76m) (Australian Spec) Ref. E
3510631 60in x 30in (1.52m x .76m) (Australian Spec) Ref. E
3510680 60in x 30in (1.52m x .76m) with Mesh to Top Rail
(Australian Spec)
Ref. C
3510628 60in x 30in (1.52m x .76m) with Mesh to Top Rail/
Standard Gate (CE Spec)
Ref. C
3510681 60in x 30in (1.52m x .76m) with Mesh to Top Rail/
Self-Closing Gate (CE Spec)
Ref. C
3510630 72in x 30in (1.83m x .76m) (Australian Spec) Ref. D
3510679 72in x 30in (1.83m x .76m) with Mesh to Top Rail
(Australian Spec)
Ref. C
3510627 72in x 30in (1.83m x .76m) with Mesh to Top Rail/
Standard Gate (CE Spec)
Ref. B
3510682 72in x 30in (1.83m x .76m) with Mesh to Top Rail/
Self-Closing Gate (CE Spec)
Ref. C
Note: Replacement Decals Must Be Ordered Sepa-
rately - See Section 8.
1 0681610 Bolt 3/8”-16NC x 1 1/4” (Grade 8) 6
2 2080040 Fastener, Huck 13
7016652 Huck Fastener Tool 1
3 2600219 Hinge 2
4 2940074 Latch 1
5 3311001 Nut #10-24NC 4
6 3311605 Locknut 3/8”-16NC 6
7 Not Available Platform Weldment (Purchase Platform Assembly) 1
8 3520072 Cap-Plug 3
9 3539685 Plate, Latch 1
10 3911008 Screw #10-24NC x 1” 4
11 4060803 Trim 1
12 4220165 Stop, Gate 1
13 4711600 Flatwasher 3/8” Narrow 12
14 4751000 Flatwasher #10 4
15 4761000 Lockwasher 3/8” 4
16 Gate Weldment Options: 1
Use 4845426 Standard (Prior to S/N40124) (Was p/n 4845327)
4845426 Standard (S/N40124 to Present)
Use 4845951 Mesh to Top Rail (Prior to S/N40124) (Was p/n
4845824)
48455951 Mesh to Top Rail (S/N40124 to Present)
3510629 48in x 30in (1.22m x .76m) With Lift Bar (CE Spec) Ref. B
3510628 60in x 30in (1.52m x .76m) With Lift Bar (CE Spec) Ref. B
3510627 72in x 30in (1.83m x .76m) With Lift Bar (CE Spec) Ref. B
51 0641418 Bolt 1/4-20NC x 2 1/4” 2
52 0681610 Bolt 3/8”-16NC x 1 1/4” (Grade 8) 6
53 0961845 Bushing 2