Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
4-4 3120870
SECTION 4 PLATFORM
S
E
C
T
I
O
N
4
P
L
A
T
F
O
R
M
54 3300151 Nut, Acorn 1/4-20NC 2
55 3311605 Lock Nut 3/8-16NC 6
56 Not Available Platform Weldment (Purchase Platform Assembly) 1
57 4420055 Tape 4
58 4711600 Flatwasher 3/8” Narrow 12
59 4740411 Washer, Nylon 4
60 4845288 Weldment, Slidebar 1
FOOTSWITCH AND COVERS INSTALLATION Ref.
101 to 105 Not Used
106 4360031 Footswitch 1
7000625 Block, Contact 2
107 to 128 Not Used
129 0641408 Bolt 1/4”-20NC x 1” 3
130 3311405 Locknut 1/4”-20NC 7
131 4740362 Washer, Fender 5
132 4460071 Terminal, Strain Relief 1
133 to 149
150 1060012 Cable, Electrical - 12/4 7ft/2.2m
151 to 152
153 4751400 Flatwasher 1/4” 4
154 to 155
156 3380434 Panel, Poly 1
157 0641406 Bolt 1/4”-20NC x 3/4” 4
0258309 WORKLIGHTS INSTALLATION (OPTIONAL) Ref. 1
201 3536089 Plate, Mounting 2
202 0641414 Bolt 1/4”-20NC x 1 3/4” 4
203 3311405 Locknut 1/4”-20NC 4
204 4711400 Flatwasher 1/4” Narrow 8
205 2920140 Worklight 2
206 4240099 Tie-Strap (Not Shown) 10
207 2820035 Loom, Vinyl (Not Shown) 9
208 Not Used
209 4460598 Connector, Strain Relief (Not Shown - Located at Con-
sole Box)
1
210 4920018 Wire, Black (Not Shown)
18in/46cm
TRAY INSTALLATIONS (OPTIONAL)
301 1580012 Tray, Storage (Center) 1
302 1580013 Tray, Storage (Rail Mounted - Not Shown) 1
FIGURE 4-1. PLATFORM INSTALLATION (CONTINUED)
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.