Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
3120870 4-13
SECTION 4 PLATFORM
S
E
C
T
I
O
N
4
P
L
A
T
F
O
R
M
FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.
Note: use p/n 1600288 when replacing complete
controller
1600278 CONTROLLER ASSEMBLY Ref. C
CONTROLLER ASSEMBLY
1 7003951 Cap 1
2 Use 7022813 Boot (was p/n 7003955) 1
3 Use 7022813 Flange (was p/n 7003954) 1
4 7003961 Microswitch 2
5 7019137 Screw 4
6 7003953 Flatwasher 4
7 7019138 Insulator 2
8 7019139 Screw 4
9 7022809 Potentiometer 2
10 7019122 Gimble (Inner) (Not Shown) 1
11 7019123 Gimble (Outer) (Not Shown) 1
PC BOARD ASSEMBLY Ref.
101 7019136 Screw 4mm x 12mm 8
102 7019135 Washer, Wavy 4mm 8
103 7019134 Cover, Heatsink 2
104 7019133 PC Board Assembly (Lift) 1
105 7019132 PC Board Assembly (Swing) 1
106 7019131 Stand-Off 8
107 7019130 Bracket 1
108 7019129 Starwasher 4mm 8
109 7019128 Nut 4mm 8