Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
7-10 3120870
SECTION 7 ELECTRICAL
S
E
C
T
I
O
N
7
E
L
E
C
T
R
I
C
A
L
FIGURE 7-3. HARNESS COMPONENTS INSTALLATION
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.
HARNESS COMPONENTS INSTALLATION Ref.
PLATFORM BOX WIRING DIAGRAM
4932999 Australian Spec Ref. 4/E
4933001 CE Spec Ref. 4/D
1 4922053 Platform Box Harness (Also Includes Terminal Block/
Rail Assembly - See Section 4)
17/G
1A 4460418 Connector - 6 Position 6
4460419 Terminal, Female 34
1B 4460265 Connector - 9 Position 2
4460268 Socket, Female 18
1C 4460266 Connector, Female - 9 Position 1
4460268 Socket, Female 7
1D 4460266 Connector, Female - 9 Position 1
4460268 Socket, Female 9
1E 3990010 Diode - 6 Amp (Not Shown) 10
1F 4460613 Connector - 21 Position 1
4460508 Pin, Male (12 Gauge) 4
4460464 Pin, Male (16 Gauge) 10
4460466 Seal, Plug 1
1G 4460503 Connector - 31 Position 1
4460464 Pin, Male (16 Gauge) 30
4460466 Seal, Plug 1
1H 4460224 Connector - 6 Position (S/N 43370 to Present
Only)
1
4460268 Socket, Female 6
1J 4460225 Connector - 6 Position (S/N 43370 to Present
Only)
1
4460267 Pin, Male 6
1K 4120035 Bulb, Light 8
4460634 Terminal (16 Gauge) 7
4460635 Terminal (12 Gauge) 8
2 to 3 Not Used
4 3990010 Diode - 6 Amp (Not Shown) 8
5 to 11 Not Used
12 4460418 Connector - 6 Position (Not Shown - 2WD/4WD
Switch)
1
13 4460419 Terminal, Female (Not Shown - Used with item 12) 3
14 Cable, Electrical - 12/4 Options: 7ft/2.13m
1060012 Prior to S/N 60663
1060515 S/N 60663 to Present
PLATFORM BOX ASSEMBLY COMPONENTS Ref.
101 4460470 Nut, Conduit 2
102 4460471 Washer 2
103 4460428 Connector, Strain Relief 1
104 2920129 Bulb, Light 8