Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
3120870 2-23
SECTION 2 TURNTABLE
S
E
C
T
I
O
N
2
T
U
R
N
T
A
B
L
E
.
FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.
GENERATOR INSTALLATION OPTIONS:
0258313 110V Generator Ref. 4/C
0258315 220V Generator Ref. 3/B
1 3580158 Pulley 1
2 Generator and Control Box Assembly Options: 1
2460011 110Volt Assembly (Prior to S/N 39711)
2460032 110Volt Assembly (S/N 39711 to Present)
Use 2460056 220Volt Assembly (was p/n 2460034)
2A 7012558 Generator - 110V 1
Note: Replacement Generator p/n 7012558 come
standard with p/n 3580134 pulley. This pulley may
not be correct for all applications. Refer to pulley
options below.
Ref.
1001100321 Generator - 220V 1
Armature Options: 1
7026199 110Volt
70000123 220Volt
7020109 Holder, Brush 4
7020108 Brush 4
7012513 Cap, Brush Holder 4
7012514 Fan 1
7020110 Bell, Front 1
7020111 Bell, Rear 1
7020190 Bearing 2
2B 7003657 Box, Control - 110V 1
Note: Replacement 110V Control Box comes with 2
std Receptacles p/n 4460190. Optional Industrial
Twist Lock Receptacles p/n 4460027 must be
ordered separately.
Box, Control - 220V Options: 1
70002235 Generator 2460034
70000127 Generator 2460056
Breaker, Circuit Options: 1
4360542 110Volt
70000126 220Volt
Receptacle Options: 1
70000124 Receptacle, Double (220V/50Hz Only)
70000125 Receptacle, Single (220V/50Hz Only)
Lamp Options: 1
2920162 Generators 2460011, 2460032 & 2460034
Not Required Generator 2460056
Switch, Toggle Options: 1
7020191 Generators 2460011, 2460032 & 2460034
Not Required Generator 2460056
3520028 Plug, Hole 2
2C Voltmeter Options: 1
2420203 110Volt
7020192 220Volt