Parts Manual Owner manual
Table Of Contents
- SECTION 1 FRAME
- FIGURE 1-1. AXLE AND STEERING INSTALLATION - 2WD WITHOUT TOW BAR
- FIGURE 1-2. AXLE AND STEERING INSTALLATION - 2WD WITH TOW BAR (S/N 49971 TO PRESENT)
- FIGURE 1-3. AXLE AND STEERING INSTALLATION - 4WD.
- FIGURE 1-4. TIRE AND WHEEL DRIVE INSTALLATIONS
- FIGURE 1-5. DRIVE BRAKE ASSEMBLY.
- FIGURE 1-6. DRIVE HUB ASSEMBLY (PRIOR TO S/N 39594).
- FIGURE 1-7. DRIVE HUB ASSEMBLY (S/N 39594 TO PRESENT)
- FIGURE 1-8. DRIVE MOTOR ASSEMBLY - REAR
- FIGURE 1-9. DRIVE MOTOR ASSEMBLY - FRONT
- FIGURE 1-10. DRIVE VALVES INSTALLATIONS
- FIGURE 1-11. TOW BAR INSTALLATION - 2WD
- FIGURE 1-12. SEMI-TRACK INSTALLATION
- SECTION 2 TURNTABLE
- FIGURE 2-1. CONTROL VALVES INSTALLATIONS
- FIGURE 2-2. MAIN CONTROL VALVE ASSEMBLY - PROPORTIONAL
- FIGURE 2-3. TURNTABLE AND SWING DRIVE INSTALLATIONS
- FIGURE 2-4. SWING MOTOR ASSEMBLY
- FIGURE 2-5. SWING BEARING ASSEMBLY
- FIGURE 2-6. DEUTZ ENGINE INSTALLATION
- FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL)
- FIGURE 2-8. PISTON PUMP ASSEMBLY
- FIGURE 2-9. TANK INSTALLATIONS
- FIGURE 2-10. GROUND CONTROL BOX ASSEMBLY
- FIGURE 2-11. ELECTRICAL OPTIONS INSTALLATION (TURNTABLE MOUNTED)
- FIGURE 2-12. HOODS INSTALLATION
- SECTION 3 BOOM
- SECTION 4 PLATFORM
- FIGURE 4-1. PLATFORM INSTALLATION
- FIGURE 4-2. PLATFORM CONSOLE ASSEMBLY
- FIGURE 4-3. CONTROLLER ASSEMBLY (LIFT & SWING) (PRIOR TO S/N39857)
- FIGURE 4-4. CONTROLLER ASSEMBLY (LIFT & SWING) (S/N39857 TO PRESENT)
- FIGURE 4-5. CONTROLLER ASSEMBLY (DRIVE & STEER) (PRIOR TO S/N39857)
- FIGURE 4-6. CONTROLLER ASSEMBLY (DRIVE & STEER) (S/N39857 TO PRESENT)
- FIGURE 4-7. CONTROLLER ASSEMBLY (SPEED)
- FIGURE 4-8. SOFT TOUCH SYSTEM INSTALLATION (S/N 49601 TO PRESENT)
- SECTION 5 CYLINDER
- FIGURE 5-1. AXLE LOCKOUT CYLINDER ASSEMBLY
- FIGURE 5-2. PLATFORM LEVEL CYLINDER ASSEMBLY
- FIGURE 5-3. LIFT CYLINDER ASSEMBLY - JIB (450AJ ONLY)
- FIGURE 5-4. LIFT CYLINDER ASSEMBLY - MAIN
- FIGURE 5-5. LIFT CYLINDER ASSEMBLY - MID
- FIGURE 5-6. LIFT CYLINDER ASSEMBLY - TOWER
- FIGURE 5-7. ROTATOR CYLINDER ASSEMBLY - PLATFORM
- FIGURE 5-8. STEER CYLINDER ASSEMBLY
- FIGURE 5-9. TELESCOPE CYLINDER ASSEMBLY
- SECTION 6 HYDRAULIC
- SECTION 7 ELECTRICAL
- SECTION 8 DECALS
- SECTION 9 RECOMMENDED SERVICE PARTS STOCK
- SECTION 10 SPECIAL OPTIONS
2-24 3120870
SECTION 2 TURNTABLE
S
E
C
T
I
O
N
2
T
U
R
N
T
A
B
L
E
2D Pulley Options: 1
3580134 Generators 2460011 & 2460056
3580276 Generators 2460032 & 2460034
2E 7020193 Cord, Power 1
2F 4460961 Connector - 4 Position (Generator 2460056 Only) 1
4460705 Terminal, Male Pin (Generator 2460056 Only) 4
3 4845531 Bracket, Generator Mounting 1
4 0200530 Arm, Adjusting 1
5 0480050 V-Belt (Prior to S/N 39711) 1
0480111 V-Belt (S/N 39711 to Present) 1
6 0701414 Bolt, Metric 14mm x 30mm 2
7 4751900 Flatwasher 9/16” 2
8 0100011 Loctite #242 (Not Shown) A/R
9 0681612 Bolt 3/8”-16NC x 1 1/2” (Grade 8) 3
10 4751600 Flatwasher 3/8” 6
11 2860012 Key, Woodruff 1
12 3311605 Locknut 3/8”-16NC 1
13 0700819 Bolt, Metric 8mm x 55mm 1
14 3740080 Relay 1
15 4460023 Connector, Strain Relief 1
16 0641508 Bolt 5/16”-18NC x 1” 1
17 4751500 Flatwasher 5/16” 2
18 Not Used
19 3520028 Plug, Hole 1
20 0721006 Bolt #10-24NC x 3/4” A/R
21 3311005 Locknut #10-24NC A/R
22 4751000 Flatwasher #10 A/R
23 Breaker, Circuit - 30 Amp Options: 1
4360294 Prior to S/N 62239
4360501 S/N 62239 to Present
24 Not Used
25 4360336 Switch, Toggle (Not Shown - Located at Platform) 1
26 4740397 Washer (Not Shown - Located at Platform) 1
27 4060802 Guard, Switch (Not Shown - Located at Platform) 1
28 Not Used
29 2820031 Heatshrink (Not Shown - Located at Platform) 1
30 3251102 Decal (Not Shown - Located at Platform) 1
31 0721008 Bolt #10-24NC x 1” 2
FIGURE 2-7. GENERATOR INSTALLATION - DEUTZ MACHINES (OPTIONAL) (CONTINUED)
FIG & ITEM # PART NUMBER DESCRIPTION QTY. REV.