Parts Manual Owner manual

Table Of Contents
3120789 400S 460SJ 1-13
SECTION 1 FRAME
203 0641606 AR Bolt 3/8in-16NC x 3/4in
8 Prior to SN 0300079125
16 SN 0300079125 to SN 0300096000
204 0681828 4 Bolt 1/2in-13NC x 3-1/2in
205 AR Bushing, Garmax Options:
0961951 4 Prior to SN 0300079125 (Top & Bottom Kingpin Locations)
(Note: See Kit)
0440291 2 SN 0300079125 to SN 0300096000 (Top Kingpin Location)
0440274 2 SN 0300079125 to SN 0300096000 (Bottom Kingpin
Location)
206 0962140 2 Bearing, Garmax
207 1 Steer Cylinder Assembly Options (See CYLINDER SECTION
for Breakdown):
Use 1684412 Prior to SN 0300087392 (was p/n 1683614)
1684412 SN 0300087392 to SN 0300096000 (was p/n 1001140283)
208 3312008 4 Nut 5/8in-11NC
209 3322201 2 Nut 3/4in-16NF
210 4 Kingpin Options:
3422716 Prior to SN 0300079125 (2 Bolt Mounting) (Note: See Kit)
3423081 SN 0300079125 to SN 0300096000 (4 Bolt Mounting)
211 Use 3841517 2 Rod-End (was p/n 3841367 Rod-End with p/n 7020180 Grease
Fitting)
Ref Note: Qty (1) p/n 4740086 Thrustwasher required between
bottom of p/n 3841517 Rod-End and Tie Rod.
212 3900109 4 Screw, Shoulder
213 4060950 1 Shield, Frame (Prior to SN 0300072506 Only)
214 1 Spindle (Left Side) Options:
Use 4130403 Prior to SN 0300079125 (was p/n 4130368)
4130405 SN 0300079125 to SN 0300096000
215 1 Spindle (Right Side) Options:
Use 4130404 Prior to SN 0300079125 (was p/n 4130369)
4130406 SN 0300079125 to SN 0300096000
216 4740086 4 Thrustwasher
217 4751800 4 Flatwasher 1/2in Regular
218 4846070 2 Tie-Rod
219 3780182 2 O-Ring (SN 0300079125 to SN 0300096000 Only) (Bottom
Kingpin Location Only)
220 to 223 Not Used
224 3020029 AR Grease, Bearing
— — — — — — — — —
300 2902400 Kingpin and Bushings Update Kit for Machines Built Prior to
SN 0300079125 (Includes Newer “SN 0300079125 to
SN 0300096000” Design Items 202, 203, 205, 210 and 219).
See Field Service Bulletin AWP-04-11.
Ref Note: Newer bushings will fit in “Prior to SN 0300079125”
axles however if kingpin holes measure 1.503in diameter or
larger in any direction, axle weldment must be replaced
before installation of kit.
Note: Spindles require drilling and tapping for 8 additional
kingpin mtg bolts. Newer design kingpins require 4 mtg
bolts each.
FIGURE 1-3. AXLE & STEERING INSTALLATION - 4WD (CONTINUED)
ITEM # PART NUMBER QTY. DESCRIPTION REV.