Service Manual Instruction Manual
Table Of Contents
- Section A. Introduction - Maintenance Safety Precautions
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires And Wheels
- 3.2 Torque Hub
- Oil Information
- Roll and Leak Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Output Carrier Disassembly
- Input Carrier Disassembly
- Hub-Spindle Disassembly
- Spindle-Brake Disassembly
- Cover Disassembly
- Cover Assembly
- Input Carrier Sub-Assembly
- Output Planet Gear Sub-Assembly
- Spindle - Brake Sub-Assembly
- Hub-Spindle Sub-Assembly
- Cover Sub-Assembly
- Main Assembly
- Integral Brake Check
- 3.3 Free Wheeling Option
- 3.4 Drive Motor
- 3.5 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.6 Steer Adjustments
- 3.7 Swing Drive
- 3.8 Swing Bearing
- 3.9 Swing Brake - Mico
- 3.10 Rotary Coupling
- 3.11 Generator
- 3.12 Deutz D2.9 L4 Engine
- 3.13 Deutz D2011 Engine
- 3.14 Spark Arrester Cleaning Instructions
- 3.15 Glow Plugs
- 3.16 Deutz EMR 2
- 3.17 Bio Fuel in Deutz Engines
- 3.18 GM Engine General Maintenance
- 3.19 GM Engine Dual Fuel System
- Fuel Filter
- Direct Electronic Pressure Regulator (DEPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Electric Lock Off
- Engine Control Module (ECM)
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.20 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Direct Electronic Pressure Regulator (DEPR) Maintenance And Inspection
- Check/Drain Oil Build-Up In 2-Stage Vaporizer
- Air Fuel Mixer/Throttle Control Device Maintenance And Inspection
- Exhaust System And Catalytic Converter Inspection And Maintenance
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Throttle Body (ETC) Replacement
- Mixer Replacement
- Electronic Pressure Regulator (EPR) Replacement
- Regulator Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.21 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- 5.1 O-Ring Lubrication
- 5.2 Cylinders - Theory of Operation
- 5.3 Cylinder Checking Procedure
- 5.4 Cylinder Removal and Installation
- Cylinder Locations
- Main Boom Telescope Cylinder Removal
- Main Boom Telescope Cylinder Installation
- Main Boom Lift Cylinder Removal
- Main Boom Lift Cylinder Installation
- Upright Level Cylinder Removal
- Upright Level Cylinder Installation
- Tower Boom Lift Cylinder Removal
- Tower Lift Cylinder Installation
- Tower Telescope Cylinder Removal
- Tower Telescope Cylinder Installation
- 5.5 Hydraulic Cylinder repair
- Tower Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Upright Level Cylinder
- Cleaning and Inspection
- Assembly
- Master Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Tower Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Platform Level (Slave) Cylinder
- Cleaning and Inspection
- Assembly
- Jib Lift Cylinder (AJ Only)
- Cleaning and Inspection
- Assembly
- Steer Cylinder
- Cleaning and Inspection
- Assembly
- Axle Lockout Cylinder
- 5.6 Hydraulic Pump (Gear)
- 5.7 Variable Pump
- 5.8 Hydraulic Component Start-Up
- 5.9 Pressure Setting Procedures
- Section 6. JLG Control System
- Section 7. Basic Electrical Information & Schematics
SECTION 3 - CHASSIS & TURNTABLE
3121616 – JLG Lift – 3-93
15 1. Turn the ignition OFF.
2. Close the manual shut-off valve on the LPG tank.
CAUTION: When disconnecting LPG fuel lines, liquid LPG may be present. Perform this step in a
well ventilated area.
3. Loosen the fuel inlet hose fitting at the inlet of the LPL.
Was fuel present when the fitting was loosened?
- - Go to Step 23 Go to Step 17
16 1. Turn OFF the ignition.
2. Connect the test light to chassis ground and probe pin A of the LPL connector.
3. Crank the engine. The test light should illuminate.
Does the test light illuminate?
- - Go to Step 20 Go to Step 21
17 1. Remove the LPG fuel filter / LPL.
2. Remove the filter from the LPL.
3. Empty the contents of the inlet side of the LPG fuel filter onto a clean surface.
4. Inspect the contents of the LPG fuel filter for an excessive amount of foreign material or
water. If necessary, locate and repair the source of contamination.
5. Verify the LPG fuel filter is not restricted or plugged.
Was a problem found?
- - Go to Step 19 Go to Step 18
18 The fuel supply system or hoses are plugged or restricted, locate and repair the problem.
Is the action complete?
- - Go to Step 26 - -
19 Replace the fuel filter. Refer to Fuel Filter Replacement.
Is t he ac ti on co mp le te ?
- - Go to Step 26 - -
20 Repair the open in the lock-off ground circuit.
Is the action complete?
- - Go to Step 26 - -
21 Repair the open in the lock-off power circuit.
Is the action complete?
- - Go to Step 26 - -
22 Replace the low pressure regulator (LPR). Refer to Low Pressure Regulator Replacement.
Is the action complete?
- - Go to Step 26 - -
23 Replace the lock-off. Refer to Lock-off Replacement.
Is the action complete?
- - Go to Step 26 - -
24 Replace the mixer assembly. Refer to Fuel Mixer Replacement.
Is t he ac ti on co mp le te ?
- - Go to Step 26 - -
25 The fuel supply system is operating normally, if a failure of the control solenoids is suspected.
Refer to Fuel Control System Diagnosis.
1. Install the test plug in the LPR secondary chamber.
2. I f yo u w ere s ent to th is ro ut in e b y a not he r dia gno sti c c har t , retu rn to th e pr ev io us dia gno sti c
procedure.
Is the action complete?
- - System OK - -
26 1. Disconnect all test equipment
2. Install the primary and secondary test port plugs.
3. Start the engine.
4. Using SNOOP or equivalent, leak check the test port plugs.
Is the action complete?
- - System OK - -
Table 3-10. LP Fuel System Diagnosis
STEP ACTION VALUE(S) YES NO