Service Manual Instruction Manual
Table Of Contents
- Section A. Introduction - Maintenance Safety Precautions
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires And Wheels
- 3.2 Torque Hub
- Oil Information
- Roll and Leak Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Output Carrier Disassembly
- Input Carrier Disassembly
- Hub-Spindle Disassembly
- Spindle-Brake Disassembly
- Cover Disassembly
- Cover Assembly
- Input Carrier Sub-Assembly
- Output Planet Gear Sub-Assembly
- Spindle - Brake Sub-Assembly
- Hub-Spindle Sub-Assembly
- Cover Sub-Assembly
- Main Assembly
- Integral Brake Check
- 3.3 Free Wheeling Option
- 3.4 Drive Motor
- 3.5 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.6 Steer Adjustments
- 3.7 Swing Drive
- 3.8 Swing Bearing
- 3.9 Swing Brake - Mico
- 3.10 Rotary Coupling
- 3.11 Generator
- 3.12 Deutz D2.9 L4 Engine
- 3.13 Deutz D2011 Engine
- 3.14 Spark Arrester Cleaning Instructions
- 3.15 Glow Plugs
- 3.16 Deutz EMR 2
- 3.17 Bio Fuel in Deutz Engines
- 3.18 GM Engine General Maintenance
- 3.19 GM Engine Dual Fuel System
- Fuel Filter
- Direct Electronic Pressure Regulator (DEPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Electric Lock Off
- Engine Control Module (ECM)
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.20 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Direct Electronic Pressure Regulator (DEPR) Maintenance And Inspection
- Check/Drain Oil Build-Up In 2-Stage Vaporizer
- Air Fuel Mixer/Throttle Control Device Maintenance And Inspection
- Exhaust System And Catalytic Converter Inspection And Maintenance
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Throttle Body (ETC) Replacement
- Mixer Replacement
- Electronic Pressure Regulator (EPR) Replacement
- Regulator Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.21 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- 5.1 O-Ring Lubrication
- 5.2 Cylinders - Theory of Operation
- 5.3 Cylinder Checking Procedure
- 5.4 Cylinder Removal and Installation
- Cylinder Locations
- Main Boom Telescope Cylinder Removal
- Main Boom Telescope Cylinder Installation
- Main Boom Lift Cylinder Removal
- Main Boom Lift Cylinder Installation
- Upright Level Cylinder Removal
- Upright Level Cylinder Installation
- Tower Boom Lift Cylinder Removal
- Tower Lift Cylinder Installation
- Tower Telescope Cylinder Removal
- Tower Telescope Cylinder Installation
- 5.5 Hydraulic Cylinder repair
- Tower Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Upright Level Cylinder
- Cleaning and Inspection
- Assembly
- Master Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Tower Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Platform Level (Slave) Cylinder
- Cleaning and Inspection
- Assembly
- Jib Lift Cylinder (AJ Only)
- Cleaning and Inspection
- Assembly
- Steer Cylinder
- Cleaning and Inspection
- Assembly
- Axle Lockout Cylinder
- 5.6 Hydraulic Pump (Gear)
- 5.7 Variable Pump
- 5.8 Hydraulic Component Start-Up
- 5.9 Pressure Setting Procedures
- Section 6. JLG Control System
- Section 7. Basic Electrical Information & Schematics
SECTION 6 - JLG CONTROL SYSTEM
3121616 – JLG Lift – 6-11
Figure 6-7. Analyzer Software Version 6.8 - Sheet 3 of 6
CALIBRATION DATA
LOAD 500LB:
CALIBRATION DATA
PLATFORM UP:
FROM
DIAGNOSTICS:
UMS
DIAGNOSTICS:
LOAD
CAPACITY LENGTH
SWITCH: CLOSED
CAPACITY ANGLE
SWITCH: CLOSED
PERCENT OF MAX
LOAD: XXX%
PLATFORM LOAD
STATE: OK
DIAGNOSTICS:
CAN STATISTICS
CAN STATISTICS
RX/SEC: X
CAN STATISTICS
TX/SEC: X
CAN STATISTICS
BUS OFF: X
CAN STATISTICS
PASSIVE: X
CAN STATISTICS
MSG ERROR: XXXX
DIAGNOSTICS:
CALIBRATION DATA
1
CALIBRATION DATA
LOAD ZERO:
1
1
1
CALIBRATION DATA
PLATFORM DN:
1
DIAGNOSTICS:
DATALOG
DATALOG:
ON: XXXh XXm
DATALOG:
ENGINE: XXXh XXm
DATALOG:
DRIVE: XXXh XXm
DATALOG:
LIFT: XXXh XXm
DATALOG:
SWING: XXXh XXm
DATALOG:
TELE: XXXh XXm
DATALOG:
MAX TEMP: XXXF
DATALOG:
MIN TEMP: XXXF
DATALOG:
MAX VOLTS: XX.XV
DATALOG:
RENTAL: XXXh XXm
DATALOG:
ERASE RENTAL?
1
CLEAR RENTAL:
YES:ENTER,NO:ESC
1
DIAGNOSTICS:
VERSIONS
GROUND MODULE
SOFTWARE: XX.XX
GROUND MODULE
COST. DATA:XX.XX
GROUND MODULE
HARDWARE: REV XX
GROUND MODULE
S/N: XXXXXX
PLATFORM MODULE
SOFTWARE: XX.XX
PLATFORM MODULE
HARDWARE: REV XX
PLATFORM MODULE
S/N: XXXXXX
PROPULSION MOD
SOFTWARE: XX.XX
TCU MODULE
SOFTWARE: XX.XX
TCU MODULE
HARDWARE: REV XX
TCU MODULE
S/N: XXXXXX
GATEWAY MODULE
SOFTWARE: XX.XX
GATEWAY MODULE
HARDWARE: REV XX
ANALYZER:
ANALYZER XX.XX
1