Service Manual Instruction Manual
Table Of Contents
- Section A. Introduction - Maintenance Safety Precautions
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires And Wheels
- 3.2 Torque Hub
- Oil Information
- Roll and Leak Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Output Carrier Disassembly
- Input Carrier Disassembly
- Hub-Spindle Disassembly
- Spindle-Brake Disassembly
- Cover Disassembly
- Cover Assembly
- Input Carrier Sub-Assembly
- Output Planet Gear Sub-Assembly
- Spindle - Brake Sub-Assembly
- Hub-Spindle Sub-Assembly
- Cover Sub-Assembly
- Main Assembly
- Integral Brake Check
- 3.3 Free Wheeling Option
- 3.4 Drive Motor
- 3.5 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.6 Steer Adjustments
- 3.7 Swing Drive
- 3.8 Swing Bearing
- 3.9 Swing Brake - Mico
- 3.10 Rotary Coupling
- 3.11 Generator
- 3.12 Deutz D2.9 L4 Engine
- 3.13 Deutz D2011 Engine
- 3.14 Spark Arrester Cleaning Instructions
- 3.15 Glow Plugs
- 3.16 Deutz EMR 2
- 3.17 Bio Fuel in Deutz Engines
- 3.18 GM Engine General Maintenance
- 3.19 GM Engine Dual Fuel System
- Fuel Filter
- Direct Electronic Pressure Regulator (DEPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Electric Lock Off
- Engine Control Module (ECM)
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.20 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Direct Electronic Pressure Regulator (DEPR) Maintenance And Inspection
- Check/Drain Oil Build-Up In 2-Stage Vaporizer
- Air Fuel Mixer/Throttle Control Device Maintenance And Inspection
- Exhaust System And Catalytic Converter Inspection And Maintenance
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Throttle Body (ETC) Replacement
- Mixer Replacement
- Electronic Pressure Regulator (EPR) Replacement
- Regulator Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.21 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- 5.1 O-Ring Lubrication
- 5.2 Cylinders - Theory of Operation
- 5.3 Cylinder Checking Procedure
- 5.4 Cylinder Removal and Installation
- Cylinder Locations
- Main Boom Telescope Cylinder Removal
- Main Boom Telescope Cylinder Installation
- Main Boom Lift Cylinder Removal
- Main Boom Lift Cylinder Installation
- Upright Level Cylinder Removal
- Upright Level Cylinder Installation
- Tower Boom Lift Cylinder Removal
- Tower Lift Cylinder Installation
- Tower Telescope Cylinder Removal
- Tower Telescope Cylinder Installation
- 5.5 Hydraulic Cylinder repair
- Tower Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Upright Level Cylinder
- Cleaning and Inspection
- Assembly
- Master Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Lift Cylinder
- Cleaning and Inspection
- Assembly
- Main Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Tower Boom Telescope Cylinder
- Cleaning and Inspection
- Assembly
- Platform Level (Slave) Cylinder
- Cleaning and Inspection
- Assembly
- Jib Lift Cylinder (AJ Only)
- Cleaning and Inspection
- Assembly
- Steer Cylinder
- Cleaning and Inspection
- Assembly
- Axle Lockout Cylinder
- 5.6 Hydraulic Pump (Gear)
- 5.7 Variable Pump
- 5.8 Hydraulic Component Start-Up
- 5.9 Pressure Setting Procedures
- Section 6. JLG Control System
- Section 7. Basic Electrical Information & Schematics

SECTION 6 - JLG CONTROL SYSTEM
3121616 – JLG Lift – 6-43
3419 JIB LIFT DOWN VALVE - SHORT TO BATTERY
3420 JIB LIFT DOWN VALVE - SHORT TO GROUND
431 FUEL SENSOR - SHORT TO BATTERY
432 FUEL SENSOR - SHORT TO GROUND
433 OIL PRESSURE - SHORT TO BATTERY
434 OIL PRESSURE - SHORT TO GROUND
435 COOLANT TEMPERATURE - SHORT TO GROUND
437 ENGINE TROUBLE CODE
438 HIGH ENGINE TEMP
4310 NO ALTERNATOR OUTPUT
4311 LOW OIL PRESSURE
4313 THROTTLE ACTUATOR FAILURE
4314 WRONG ENGINE SELECTED - ECM DETECTED
4322 LOSS OF ENGINE SPEED SENSOR
4323 SPEED SENSOR READING INVALID SPEED
4326 FUEL ACTUATOR - SHORT TO GROUND
4327 FUEL ACTUATOR - OPEN CIRCUIT
4328 FUEL ACTUATOR - SHORT TO BATTERY
4329 FUEL ACTUATOR - CURRENT FEEDBACK READING TOO LOW
4330 FUEL ACTUATOR - CURRENT FEEDBACK READING LOST
441 BATTERY VOLTAGE TOO LOW - SYSTEM SHUTDOWN
442 BATTERY VOLTAGE TOO HIGH - SYSTEM SHUTDOWN
443 LSS BATTERY VOLTAGE TOO HIGH
444 LSS BATTERY VOLTAGE TOO LOW
445 BATTERY VOLTAGE LOW
662 CANBUS FAILURE - PLATFORM MODULE
663 CANBUS FAILURE - LOAD SENSING SYSTEM MODULE
666 CANBUS FAILURE - ENGINE CONTROLLER
6613 CANBUS FAILURE - EXCESSIVE CANBUS ERRORS
6622 CANBUS FAILURE - TCU MODULE
6629 CANBUS FAILURE - TELEMATICS CANBUS LOADING TOO HIGH
681 REMOTE CONTRACT MANAGEMENT OVERRIDE - ALL FUNCTIONS IN CREEP
813 CHASSIS TILT SENSOR NOT CALIBRATED
814 CHASSIS TILT SENSOR OUT OF RANGE
815 CHASSIS TILT SENSOR DISAGREEMENT
821 LSS CELL #1 ERROR
822 LSS CELL #2 ERROR
823 LSS CELL #3 ERROR
824 LSS CELL #4 ERROR
825 LSS HAS NOT BEEN CALIBRATED
826 RUNNING AT CREEP - PLATFORM OVERLOADED
827 DRIVE & BOOM PREVENTED - PLATFORM OVERLOADED
828 LIFT UP & TELE OUT PREVENTED - PLATFORM OVERLOADED
Table 6-6. Fault Code List
DTC Text