Service Manual Manual

SECTION 1 - SPECIFICATIONS
3120840 – JLG Lift – 1-5
1.6 LUBRICATION
Deutz F4M1011F Engine
Single Viscosity Oil (CD-SE, CD-SF).
NOTE: Crankcase oil should be MIL-L2104B/MIL-L2104C or
have properties of API classification CC/CD grades.
Continental TMD27 Engine
Single Viscosity Oils (CC-CD).
Hydraulic Oil
NOTE: Hydraulic oils must have anti-wear qualities at least
to API Service Classification GL-3, and sufficient
chemical stability for mobile hydraulic system ser-
vice. JLG Industries recommends Mobilfluid 424
hydraulic oil, which has an SAE viscosity index of
152.
NOTE: When temperatures remain below 20° F (-7 degrees
C), JLG Industries recommends the use of Mobil
DTE 13M.
Aside from JLG recommendations, it is not advisable to
mix oils of different brands or types, as they may not con-
tain the same required additives or be of comparable vis-
cosities. If use of hydraulic oil other than Mobilfluid 424 is
desired, contact JLG Industries for proper recommenda-
tions.
When Outside Temperature is
Consistently
Use SAE Viscosity
Number
-20°F. to +25°F. (-29°C. to +4°C.) *10W
+5°F. to +50°F. (+15°C. to +10°C.) 20W-20
+40°F. to +85°F. (+4°C. to +30°C.) 30
Above 75°F. (24°C.) 40
Multi Viscosity Oil (CD-SE, CD-SF)
*This viscosity can be used at colder temperatures with
engine oil preheating.
When Outside
Temperature is
Consistently
Use SAE Viscosity Number
-40°F. to +75°F. (-40°C. to
+24°C.)
*5W-30 (Synthetic)
-15°F. to +70°F. (-26°C. to
+21°C.)
10W-30
-15°F. to +85°F. (-26°C. to
+30°C.)
10W-40
Above -5°F. (-21°C.) 15W-40
-5°F. to +75°F. (-21°C. to
+24°C.)
15W-30
*This viscosity can be used at colder temperatures with
engine oil preheating.
When Outside
Temperature is
Consistently
Use SAE Viscosity Number
+32°F. to +77°F. (+0°C. to
+25°C.)
20
Above +77°F. (+25°C.) 30
Below +32°F. (+0°C.) 10W
Multi Viscosity Oil (CC-CD)
*Not recommended for severe service, including high RPM
operation
When Outside
Temperature is
Consistently
Use SAE Viscosity Number
Below +32°F. (+0°C.) 10W-30
Ta b l e 1 - 3 . H y d r a u l i c O i l
HYDRAULIC SYSTEM
OPERATING
TEMPERATURE RANGE
SAE VISCOSITY GRADE
-18° C to +83° C 10W
-18° C to +99° C 10W-20, 10W-30
+10° C to +210° C 20W-20
Table 1-4. Mobil DTE 13M Specs
ISO Viscosity Grade #32
Specific Gravity 0.877
Pour Point, Max -40˚F (-40˚C)
Flash Point, Min. 330˚F (166˚C)
Viscosity
at 40° C 33cSt
at 100° C 6.6 cSt
at 100° F 169 SUS
at 210° F 48 SUS
cp at - 20 ° F 6, 200
Viscosity Index 140