Service Manual Owner's manual
Table Of Contents
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires & Wheels
- 3.2 Wheel Drive Assembly, 2WD
- 3.3 Drive Motor - 2WD (Prior to S/N 83331)
- 3.4 Drive Motor (S/N 83331 to Present)
- 3.5 Torque Hub
- 3.6 Wheel Drive Assembly, 4WD
- 3.7 Torque Hub (4WD Machines W/ Integral Brake)
- Roll, Leak and Brake Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Input Carrier Disassembly
- Output Carrier Disassembly
- Housing-Spindle Disassembly
- Spindle-Brake Disassembly
- Input Carrier Sub-Assembly
- Output Carrier Sub-Assembly
- Spindle-Brake Sub-Assembly
- Housing-Spindle Sub-Assembly
- DW2B Integral Brake Check
- Main Assembly
- 3.8 Drive Brake, 2WD - Mico (Prior to S/N 83331)
- 3.9 Re-Aligning torque hub input coupling
- 3.10 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.11 Swing Drive Hub
- 3.12 Swing Brake - Mico (Prior to S/N 66417)
- 3.13 Swing Motor (Prior to S/N 66417)
- 3.14 Swing Motor (S/N 66417 to Present)
- 3.15 Procedure For Setting Gear Backlash
- 3.16 Swing Bearing
- 3.17 Rotary Coupling
- 3.18 Generator
- 3.19 Ford EFI Engine
- 3.20 Deutz EMR 2 (S/N 85332 to Present)
- 3.21 GM Engine General Maintenance
- 3.22 GM Engine Dual Fuel System
- Fuel Filter
- Electric Lock Off
- EPR Assembly
- Low Pressure Regulator (LPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Engine Control Module
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.23 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Electronic Pressure Regulator (EPR) Assembly Replacement
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Electronic Throttle Control Replacement
- Mixer Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.24 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- Section 6. JLG Control System
- Section 7. Basic Electrical information & schematics
SECTION 3 - CHASSIS & TURNTABLE
3121139 – JLG Lift – 3-149
Fuel Filter
After the fuel is drawn into the fuel pump, the fuel flows
through the gasoline fuel filter. The fuel filter will trap small
particles as the fuel passes through the filter to remove
debris and prevents the fuel pressure and temperature
manifold and fuel injectors from becoming damaged.
Maintenance of the fuel filter is required as indicated in
Section 1.
Fuel Injector Rail
Fuel flows from the fuel pressure and temperature mani-
fold assembly to the fuel rails where the fuel is delivered to
the fuel injectors. The fuel rail also contains a Schrader
valve which is utilized to test the regulated pressure of the
fuel system.
Fuel Injector
The fuel supply is maintained on the top of the injector
from the injector rail. The injector is fed a "pulse" signal
through the wire harness which causes the injector to
open. During regular operating conditions the ECM con-
trols the opening and duration of opening of the injector.
During lower RPM operation the injector signals or
"pulses" are less frequent then when the engine is operat-
ing at higher RPMs. The engine has been calibrated to
deliver the precise amount of fuel for optimum perfor-
mance and emission control.
3.23 GM ENGINE FUEL SYSTEM REPAIR
Propane Fuel System Pressure Relief
THE PROPANE FUEL SYSTEM OPERATES AT PRESSURES UP TO
312 PSI (21.5 BAR). TO MINIMIZE THE RISK OF FIRE AND PER-
SONAL INJURY, RELIEVE THE PROPANE FUEL SYSTEM PRES-
SURE (WHERE APPLICABLE) BEFORE SERVICING THE PROPANE
FUEL SYSTEM COMPONENTS.
To relieve propane fuel system pressure:
1. Close the manual shut-off valve on the propane fuel
tank.
2. Start and run the vehicle until the engine stalls.
3. Turn the ignition switch OFF.
RESIDUAL VAPOR PRESSURE WILL BE PRESENT IN THE FUEL
SYSTEM. ENSURE THE WORK AREA IS WELL VENTILATED
BEFORE DISCONNECTING ANY FUEL LINE.
Propane Fuel System Leak Test
NEVER USE AN OPEN FLAME OF ANY TYPE TO CHECK FOR PRO-
PANE FUEL SYSTEM LEAKS.
Always inspect the propane fuel system for leaks after per-
forming service. Check for leaks at the fittings of the ser-
viced or replaced component. Use a commercially
available liquid leak detector or an electronic leak detec-
tor. When using both methods, use the electronic leak
detector first to avoid contamination by the liquid leak
detector.