Service Manual Owner's manual
Table Of Contents
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires & Wheels
- 3.2 Wheel Drive Assembly, 2WD
- 3.3 Drive Motor - 2WD (Prior to S/N 83331)
- 3.4 Drive Motor (S/N 83331 to Present)
- 3.5 Torque Hub
- 3.6 Wheel Drive Assembly, 4WD
- 3.7 Torque Hub (4WD Machines W/ Integral Brake)
- Roll, Leak and Brake Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Input Carrier Disassembly
- Output Carrier Disassembly
- Housing-Spindle Disassembly
- Spindle-Brake Disassembly
- Input Carrier Sub-Assembly
- Output Carrier Sub-Assembly
- Spindle-Brake Sub-Assembly
- Housing-Spindle Sub-Assembly
- DW2B Integral Brake Check
- Main Assembly
- 3.8 Drive Brake, 2WD - Mico (Prior to S/N 83331)
- 3.9 Re-Aligning torque hub input coupling
- 3.10 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.11 Swing Drive Hub
- 3.12 Swing Brake - Mico (Prior to S/N 66417)
- 3.13 Swing Motor (Prior to S/N 66417)
- 3.14 Swing Motor (S/N 66417 to Present)
- 3.15 Procedure For Setting Gear Backlash
- 3.16 Swing Bearing
- 3.17 Rotary Coupling
- 3.18 Generator
- 3.19 Ford EFI Engine
- 3.20 Deutz EMR 2 (S/N 85332 to Present)
- 3.21 GM Engine General Maintenance
- 3.22 GM Engine Dual Fuel System
- Fuel Filter
- Electric Lock Off
- EPR Assembly
- Low Pressure Regulator (LPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Engine Control Module
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.23 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Electronic Pressure Regulator (EPR) Assembly Replacement
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Electronic Throttle Control Replacement
- Mixer Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.24 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- Section 6. JLG Control System
- Section 7. Basic Electrical information & schematics
SECTION 4 - BOOM & PLATFORM
3121139 – JLG Lift – 4-3
5. Using a 3/8 drive extension approximately 4 feet (1.2
m) long, remove the bolts and washers securing the
cable mount block to the boom fly section.
6. Remove the four bolts, shims, and attachment
blocks that secure the telescope cylinder barrel to
the boom mid section.
7. Remove the four bolts, shims, and mounting blocks
that secure the telescope cylinder rod to the boom
base section.
WHEN REMOVING THE TELESCOPE CYLINDER FROM THE BOOM,
IT MAY BE NECESSARY AT SOME POINT TO TURN THE CYLINDER
SLIGHTLY IN ORDER TO CLEAR ASSEMBLIES MOUNTED WITHIN
THE BOOM. CARE MUST BE TAKEN TO MOVE THE CYLINDER
SLOWLY FROM THE BOOM. DAMAGE TO COMPONENTS MAY
RESULT FROM FORCIBLE IMPACT WITH THESE ASSEMBLIES.
NOTE: The telescope cylinder weighs approximately 600
lbs. (275 kg).
8. Using overhead cranes or other suitable lifting/sup-
porting devices, carefully pull the telescope cylinder
out from the back of the boom. At the same time,
also pull the cable mount block out so the extension
cables come out with the telescope cylinder and do
not bind. The lifting/supporting devices will have to
be repositioned to support the weight of the cylinder
as it is drawn out of the boom.