Service Manual Owner's manual
Table Of Contents
- Section 1. Specifications
- Section 2. General
- Section 3. Chassis & Turntable
- 3.1 Tires & Wheels
- 3.2 Wheel Drive Assembly, 2WD
- 3.3 Drive Motor - 2WD (Prior to S/N 83331)
- 3.4 Drive Motor (S/N 83331 to Present)
- 3.5 Torque Hub
- 3.6 Wheel Drive Assembly, 4WD
- 3.7 Torque Hub (4WD Machines W/ Integral Brake)
- Roll, Leak and Brake Testing
- Tightening and Torquing Bolts
- Main Disassembly
- Input Carrier Disassembly
- Output Carrier Disassembly
- Housing-Spindle Disassembly
- Spindle-Brake Disassembly
- Input Carrier Sub-Assembly
- Output Carrier Sub-Assembly
- Spindle-Brake Sub-Assembly
- Housing-Spindle Sub-Assembly
- DW2B Integral Brake Check
- Main Assembly
- 3.8 Drive Brake, 2WD - Mico (Prior to S/N 83331)
- 3.9 Re-Aligning torque hub input coupling
- 3.10 Oscillating Axle Bleeding Procedure and Lockout Test
- 3.11 Swing Drive Hub
- 3.12 Swing Brake - Mico (Prior to S/N 66417)
- 3.13 Swing Motor (Prior to S/N 66417)
- 3.14 Swing Motor (S/N 66417 to Present)
- 3.15 Procedure For Setting Gear Backlash
- 3.16 Swing Bearing
- 3.17 Rotary Coupling
- 3.18 Generator
- 3.19 Ford EFI Engine
- 3.20 Deutz EMR 2 (S/N 85332 to Present)
- 3.21 GM Engine General Maintenance
- 3.22 GM Engine Dual Fuel System
- Fuel Filter
- Electric Lock Off
- EPR Assembly
- Low Pressure Regulator (LPR)
- Air Fuel Mixer
- Electronic Throttle Control (ETC)
- Engine Control Module
- Heated Exhaust Gas Oxygen Sensor
- Gasoline Multi Point Fuel Injection System (MPFI)
- Gasoline Fuel Pump
- Gasoline Pressure And Temperature Sensor Manifold
- Fuel Filter
- Fuel Injector Rail
- Fuel Injector
- 3.23 GM Engine Fuel System Repair
- Propane Fuel System Pressure Relief
- Propane Fuel System Leak Test
- Propane Fuel Filter Replacement
- Electronic Pressure Regulator (EPR) Assembly Replacement
- Temperature Manifold Absolute Pressure (TMAP) Sensor
- Electronic Throttle Control Replacement
- Mixer Replacement
- Coolant Hose Replacement
- Vapor Hose Replacement
- Engine Control Module Replacement
- Heated Exhaust Gas Oxygen Sensor Replacement
- 3.24 GM Engine LPG Fuel System Diagnosis
- Section 4. Boom & Platform
- Section 5. Hydraulics
- Section 6. JLG Control System
- Section 7. Basic Electrical information & schematics
SECTION 4 - BOOM & PLATFORM
3121139 – JLG Lift – 4-25
4.6 ELECTRONIC PLATFORM LEVELING
Description
Electronic platform leveling replaces the conventional
hydraulic method of platform leveling. The term "platform
leveling" does not refer to the system maintaining the plat-
form at level (or 0°) with respect to gravity, but instead
refers to the controls automatically maintaining the plat-
form within several degrees of a preset angle.
To control electronic platform leveling the platform is
equipped with a pair of tilt sensors, one primary and one
secondary, mounted to the non-rotating portion of the
platform rotator, level up and level down valves that are
used to provide proportional hydraulic flow for each direc-
tional function, and a control module that interprets the
sensor readings and actuates the leveling valves.
PRIMARY AND SECONDARY TILT SENSOR INTERAC-
TION
Two tilt sensors, mounted on each side of the platform
support, are used to measure the incline of the platform
with respect to gravity and control the automatic platform
angle control function. The right one (as viewed from
standing in the platform) is used as the primary sensor
and the left one as a secondary back up sensor.
If a fault occurs with the primary sensor, control will revert
to the secondary sensor. (This is discussed in more detail
in the error response section.)
Because of the mounting orientation of the tilt sensors, the
primary tilt sensor will output ascending voltage values
with increases in positive platform tilt angle. The backup
or secondary tilt sensor will output descending voltage
values with increases in positive platform angle.