User Manual

BOOM LIFT MODELS X14J
JLG
118
X14JR0420113
Size PITCH
Tensile
Stress
Area
Clamp
Load
Torque
(Dry or Loctite®
263
TM
)
Torque
(Lub)
Torque
(Loctite® 262
TM
OR Vibra-
TITE
TM
131)
Torque
(Loctite®
242
TM
or 271
TM
OR Vibra-
TITE
TM
111 or
140)
Clamp
Load
Torque
(Dry or Loctite®
263
TM
)
K = 0.20
Torque
(Lub OR Loctite®
242
TM
or 271
TM
OR
Vibra-TITE
TM
111 or
140)
K= 0.18
Torque
(Loctite® 262
TM
OR
Vibra-TITE
TM
131)
K=0.15
Clamp Load
See Note 4
Torque
(Dry or Loctite®
263
TM
)
K = .17
Torque
(Lub OR Loctite®
242
TM
or 271
TM
OR Vibra-TITE
TM
111 or 140)
K = .16
Torque
(Loctite® 262
TM
OR Vibra-TITE
TM
131)
K = .15
Sq mm KN [N.m] [N.m] [N.m] [N.m] KN [N.m] [N.m] [N.m] kN [N.m] [N.m] [N.m]
3 0,5 5,03 2,19 1,3 1,0 1,2 1,4 3,13
3.5 0,6 6,78 2,95 2,1 1,6 1,9 2,3 4,22
4 0,7 8,78 3,82 3,1 2,3 2,8 3,4 5,47 5 0,8 14,20 6,18 6,2 4,6 5,6 6,8 8,85 6 1 20,10 8,74 11 7,9 9,4 12 12,5 12,5 13 12 11 7 1 28,90 12,6 18 13 16 19 18,0 25 23 19 18,0 21 20 19 8 1,25 36,60 15,9 26 19 23 28 22,8 37 33 27 22,8 31 29 27
10 1,5 58,00 25,2 50 38 45 55 36,1 70 65 55 36,1 61 58 54 12 1,75 84,30 36,7 88 66 79 97 52,5 125 115 95 52,5 105 100 95 14 2 115 50,0 140 105 126 154 71,6 200 180 150 71,6 170 160 150
16 2 157 68,3
219 164 197 241
97,8
315 280 235 97,8 265 250 235
18 2,5 192 83,5 301 226 271 331 119,5 430 385 325 119,5 365 345 325 20 2,5 245 106,5 426 320 383 469 152,5 610 550 460 152,5 520 490 460 22 2,5 303 132,0 581 436 523 639 189,0 830 750 625 189,0 705 665 625 24 3 353 153,5 737 553 663 811 222,0 1065 960 800 220,0 900 845 790 27 3 459 199,5 1080 810 970 1130 286,0 1545 1390 1160 286,0 1315 1235 1160 30 3,5 561 244,0 1460 1100 1320 1530 349,5 2095 1885 1575 349,5 1780 1680 1575 33 3,5 694 302,0 1990 1490 1790 2090 432,5 2855 2570 2140 432,5 2425 2285 2140 36 4 817 355,5 2560 1920 2300 2690 509,0 3665 3300 2750 509,0 3115 2930 2750 42 4,5 1120 487,0 4090 3070 3680 4290 698,0 5865 5275 4395 698,0 4985 4690 4395
4. CLAMP LOAD LISTED FOR SHCS IS SAME AS GRADE 8 OR CLASS 10.9 AND DOES NOT REPRESENT FULL STRENGTH CAPABILITY OF SHCS. IF HIGHER LOAD IS REQUIRED, ADDITIONAL TESTING IS REQUIRED. *3. ASSEMBLY USES HARDENED WASHER OR FASTENER IS PLACED AGAINST PLATED STEEL OR RAW ALUMINUM
Spec #4150701Values for Zinc Yellow Chromate Fasteners (Ref 4150707)
CLASS 10.9 METRIC (HEX HEAD) BOLTS
CLASS 10 METRIC NUTS
CLASS 12.9 SOCKET HEAD CAP SCREWS M3 - M5*
CLASS 8.8 METRIC (HEX HEAD) BOLTS
CLASS 8 METRIC NUTS
CLASS 12.9 SOCKET HEAD CAP SCREWS
M6 AND ABOVE*
NOTES: 1. THESE TORQUE VALUES DO NOT APPLY TO CADMIUM PLATED FASTENERS 2. ALL TORQUE VALUES ARE STATIC TORQUE MEASURED PER STANDARD AUDIT METHODS TOLERANCE = ±10%
Torque Specs