AT-3101-J 1/2-INCH HEAVY DUTY IMPACT WRENCH CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE IMPACT WRENCH AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
Introduction Congratulations on the purchase of your new 1/2-Inch Heavy Duty Impact Wrench! You can be assured your heavy duty impact wrench was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. The John Deere 1/2” Heavy Duty Impact Wrench is designed for demanding fastening and maintenance applications.
Table of Content INTRODUCTION .................................................................................................... 2 TABLE OF CONTENTS ......................................................................................... 3 SAFETY .................................................................................................................. 4-6 RECOGNIZE SAFETY INFORMATION ................................................ UNDERSTAND SIGNAL WORDS .........................................
Safety RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your pneumatic tool or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A "DANGER, WARNING or CAUTION" safety warning will be surrounded by a "SAFETY ALERT BOX." This box is used to designate and emphasize Safety Warnings that must be followed when operating this tool.
WARNING ALWAYS WEAR APPROVED EYE PROTECTION Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87.1, Occupational and Educational Eye and Face Protection. Look for the marking Z87.1 on your eye protection to insure that it is an approved style. For further information, ANSI Z87.1, Occupational and Educational Eye and Face Protection, is available from the American National Standards Institute, Inc., 11 West 42nd Street, New York, NY 10036.
WARNING AVOID PROLONGED EXPOSURE TO VIBRATION Pneumatic tools can vibrate during use. Prolonged exposure to vibration or very repetitive hand and arm movements, can cause injury. Stop using any tool if discomfort, tingling feeling or pain occurs. You should consult your physician before resuming use of the tool. CAUTION 90 PSIG MAXIMUM Designed to operate at an air pressure of 90 pounds per square inch gauge pressure (90 PSIG) maximum, at the tool. Use of higher air pressure can, and may cause injury.
Installation Designed to operate on 90 PSIG, lower pressure (below 90 PSIG) will reduce performance of the tool while higher air pressure (over 90 PSIG) raises the performance of the tool beyond its rated capacity and could cause serious damage to tool and user. Always use clean dry air. Excessive moisture and dirt will greatly reduce the life of any air motor. We recommend the installation of an in-line filter-regulator-lubricator as close to the tool as possible.
Operation PRE-OPERATION: Before the tool is connected to the air supply, clear the air hose of accumulated dust and moisture. Before removing a tool for service or changing sockets, make sure the air line is shut-off and drained of air. This will prevent the tool from operating if the throttle is accidentally engaged. OPERATION: Impact wrench has a built-in power regulator, which can be adjusted by turning the valve counter-clockwise to increase and clockwise to decrease.
Troubleshooting Solution Symptom Problem Loss of Power 1. Low air pressure 1. Check air supply. For rated performance, 90 PSI air pressure is required at the tool, with tool operating 2. Improper lubrication or dirt build up 2. Check for wet or dirty air. Wet air tends to wash lubricant away. Dirt or foreign matter will impede the action of the motor. If dirt or water has entered the tool, flush with John Deere AT-4003. 3. Worn motor parts, or other problems 3. Contact your customer service.
Limited Warranty John Deere Two-Year Limited Warranty. John Deere Wrench, Models covered in this manual, are warranted by John Deere to the original user against defects in workmanship or materials under normal use for two years after date of purchase. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as John Deere designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at John Deere’s option.
Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. While John Deere attempts to assure that its products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the product is installed or used.
Introduction Félicitations de l'achat de votre nouveau la clé à impact à usage industrie carrée! Vous pouvez être assuré que votre nouveau la clé à impact à usage industrie carrée a été construit avec le plus haut niveau de précision et de fiabilité. Chaque composant a été rigoureusement testé par des techniciens pour assurer la qualité, la durabilité et la performance de ce outil pneumatique.
Table Des Matieres INTRODUCTION .................................................................................................... 12 TABLE DES MATIERESRE ................................................................................... 13 SÉCURITÉ .............................................................................................................. 14-16 RECONNAÎTRE LES SYMBOLES DE MISE EN GARDE .................... COMPRENDRE LES TERMES DE MISE EN GARDE .........................
Sécurité RECONNAÎTRE LES SYMBOLES DE MISE EN GARDE Voici le symbole de mise en garde. Lorsqu'il apparaît sur la outil pneumatique ou dans la présente publication, c'est pour prévenir d'un risque potentiel de blessure. Respecter tous les conseil de sécurité ainsi que les consignes générales de prévention des accidents. COMPRENDRE LES TERMES DE MISE EN GARDE Les avertissements de sécurité "DANGER, AVERTISSEMENT ou ATTENTION" seront entourés par un "ENCADRE ALERTE SECURITE".
AVERTISSEMENT PORTEZ TOUJOURS DES LUNETTES DE PROTECTION HOMOLOGUÉES Les lunettes de protection antichoc doivent être au moins conformes à la norme ANSI Z87.1 relative à la protection des yeux et du visage sur les lieux de travail et d’apprentissage. Recherchez l’indication Z87.1 sur vos lunettes de protection pour vous assurer qu’elles sont d’un type homologué. Pour des informations complémentaires, vous pou-vez vous procurer le texte de la norme ANSI Z87.
AVERTISSEMENT ÉVITEZ UNE EXPOSITION PROLONGÉE AUX VIBRATIONS Les outils pneumatiques peuvent vibrer en cours de fonctionnement. Une exposition prolongée aux vibrations ou des mouvements très répétitifs de la main et du bras peuvent provoquer des blessures. Arrêtez de vous servir d’un outil quelconque en cas de gêne, de picotements ou de douleur. Vous devez consulter votre médecin avant de vous resservir de l’outil.
Installation L’outil est conçu pour fonctionner à une pression de 620 kPa. Son fonctionnement à une pression inférieure rend l’outil moins performant, alors que son fonctionnement à une pression supérieure accroît ses performances audelà de sa capacité nominale et risque d’endommager l’outil et de blesser l’utilisateur. Alimentez toujours l’outil en air propre et sec. Une humidité et une saleté excessives réduisent grandement la durée de service de tout moteur pneumatique.
Fonctionnement AVANT UTILISATION Avant de raccorder l’outil à l’alimentation en air, nettoyez le tuyau d’air pour le débarrasser de la poussière et de l’eau. Avant de débrancher un outil pour entretien ou changement de douilles, veillez à couper l’alimentation en air et à purger le tuyau de l’air qu’il contient. Cela empêche l’outil de se mettre en marche si sa commande est actionnée accidentellement.
Dépannage Symptôme Perte de puissance Solution Probléme 1. Pression d’air trop basse 1. Vérifiez l’alimentation en air. Pour obtenir le rendement prévu, l’outil en marche doit être alimenté en air comprimé à 620 kPa 2. Mauvaise lubrification ou encrassement 2. Vérifiez l’air pour voir s’il est humide ou sale. Un air humide tend à entraîner le lubrifiant. La crasse ou tout autre corps étranger gêne le fonctionnement du moteur.
Garantie limitée Garantie limitée deux John Deere. Les modèles de cliquet John Deere, traités dans ce manuel sont garantis par John Deere contre tout vice de matériau et de fabrication pendant deux an à compter de la date d’achat par l’acheteur d’origine et si utilisés selon les normes indiquées.
Appropriation du produit. De nombreuses juridictions possèdent des codes et une législation concernant la vente, la construction, l’installation et/ou l’utilisation particulière de produits pouvant différer de celles en vigueur dans les régions voisines. Bien que John Deere fait de son mieux afin que ses produits soient conformes à la dite législation, John Deere ne peut garantir cette conformité et ne saurait être responsable de la façon dont ce produit a été installé ou utilisé.
Introduccion ¡Felicitaciones por la compra de su nueva Llaves de Impacto de 1/2" John Deere! Puede estar seguro que su llaves de llave de impacto fue construida con el nivel más alto de precisión y exactitud. Cada componente ha sido probado rigurosamente por técnicos para asegurar la calidad, la resistencia y el rendimiento de esta unidad. La llave de impacto de 1/2" (12,7 mm) de John Deere está diseñada para una amplia variedad de aplicaciones.
Tabla de Materias INTRODUCCION .................................................................................................... 22 TABLA DE MATERIAS .......................................................................................... 23 SEGURIDAD .......................................................................................................... 24-26 INFORMATION DE SÉCURITÉ RECONOCER .................................... PALABRAS DE ALERTA QUE ENTIENDO .......................................
Seguridad INFORMATION DE SÉCURITÉ RECONOCER El símbolo indicado a “Símbolo de Alerta de Seguridad”. Este símbolo se usa para alertarlo acerca de artículos o procedimientos que podrían ser peligrosos para usted u otras personas usando este equipo. PALABRAS DE ALERTA QUE ENTIENDO Estos párrafos están rodeados por una “CASILLA DE ALERTA DE SEGURIDAD”. Esta casilla se usa para designar y enfatizar las Advertencias de Seguridad que deben seguirse al operar esta herramienta.
ADVERTENCIA SIEMPRE USE PROTECCIÓN PARA LOS OJOS APROBADA La protección para los ojos, resis-tente al impacto, tiene que cumplir o exceder los estándares establecidos en ANSI Z87.1 de Estados Unidos sobre la Protección de los Ojos y de la Cara en el Trabajo y la Educación. Mire la sección Z87.1 sobre la protección para los ojos para asegurarse que está usando un estilo aprobado. Para más información la publicación de ANSI Z87.
ADVERTENCIA EVITE LA EXPOSICIÓN PROLONGADA A LA VIBRACIÓN Las herramientas neumáticas pueden vibrar durante el uso. La exposición prolongada a la vibración o los movimientos de las manos o de los brazos muy repetidos pueden producir lesiones. Deje de usar cualquier herramienta si siente incomodidad, hormigueo o dolor. Debe consultar a su doctor antes de volver a usar la herramienta.
Instalación La herramienta ha sido diseñada para operar a 620 kPa, por lo tanto, la presión más baja (por debajo de 620 kPa) reducirá su rendimiento y la presión de aire más alta (sobre 620 kPa) aumentará el rendimiento de la herramienta por sobre su capacidad nominal, lo que podría dañarla gravemente o lesionar al usuario. Siempre use aire limpio y seco. La humedad excesiva y la mugre reducen considerablemente la duración de cualquier motor de aire.
Operación ANTES DEL USO Antes de que la herramienta se conecte con el abastecimiento de aire, despeje el polvo y la humedad que se han acumulado en la manguera de aire. Antes de remover una herramienta para darle servicio o para cambiar casquillos asegúrese que la tubería de aire esté apagada y sin aire. Esto evitará que la herramienta opere si el mando se engancha por accidente.
Localizacion de Fallas Síntoma Solucion Causa(s) Posible(s) Pérdida de energía 1. Baja presión de aire. 1. Revise el abastecimiento de aire. Se necesita la presión de aire de 620 kPa en la herramienta cuando está operando, para lograr el rendimiento de capacidad nominal. 2. Mala lubricación o 2. acumulación de mugre. Revise si hay aire mojado o sucio. El aire mojado tiende a lavar el lubricante. La mugre o los materiales extraños impiden el funcionamiento del motor.
Garantía Limitada Garantía Limitada de John Deere por Dos Año. Llave de Trinquete John Deere, y los Modelos tratados en este manual están garantizados por John Deere para el comprador original contra defectos en la fabricación o el material bajo uso normal por dos año a partir de la fecha de compra.
Uso adecuado del producto. Muchas jurisdicciones tienen códigos o reglamentos que regulan las ventas, fabricación, instalación y/o uso del producto para ciertos usos específicos, los cuales pueden variar en áreas circunvecinas. John Deere trata de que sus productos cumplan con dichos códigos o reglamentaciones, sin embargo, el cumplimiento de los mismos no se puede garantizar y la compañía no se hace responsable por la forma en la cual el producto se instala o usa.
#37-0647-090403 32 © Copyright 2003.