Operating Guide

Additional Safety Information
Towing Loads Safely
● Stopping distance increases with speed and weight of towed load.
Travel slowly and allow extra time and distance to stop.
● Total towed weight must not exceed Towing Capacity stated in
Specications of this manual.
● Excessive towed load can cause loss of traction and loss of control
on slopes. Reduce towed weight when operating on slopes.
● Never allow children or others in or on towed equipment.
● Use only approved hitches. Tow only with a machine that has a
hitch designed for towing. Do not attach towed equipment except at
the approved hitch point.
● Towed equipment increases the risk of rollover on slopes. Refer to
the Operating on Slopes and Near Terrain Hazards section for more
information.
● Do not turn sharply. Use additional caution when turning or
operating on adverse surface conditions. Use care when reversing.
Safe Transportation
Follow instructions in the Transporting Machine on Trailer section.
● Use a full-width loading ramp at least 30 cm (12 in) wider than the
machine, never two separate ramps.
Service and Maintenance
● Proper service and maintenance of the machine is essential.
● Keep all parts in good condition, keep all nuts and bolts tight, and
repair any damage immediately. Stop and inspect the machine
immediately if you strike an object.
● Ensure that all safety devices, discharge chute, and grass catcher
components are in good condition and replace when necessary.
● Understand service procedures thoroughly before working on the
machine. If you do not understand the service procedures or are
uncomfortable working in your machine, contact your servicing
dealer.
● Disconnect the battery or all spark plug wires before servicing the
machine. Disconnect negative terminal rst and positive last. Install
positive terminal rst and negative last.
● Some components could have stored energy in springs or hydraulic
components. Servicing procedures described in the Service section
describe how to perform service and maintenance tasks safely.
● Support any machine elements that must be raised for service
work. Use jack stands or service locks to support components
when needed.
Disposing of Waste Products and Chemicals
● Waste products, such as used oil, fuel, coolant, brake uid, and
batteries can harm the environment and people.
● Do not use beverage containers for waste uids – someone can
mistakenly drink from them.
● A Safety Data Sheet (SDS) provides specic details on chemical
products: Physical and health hazards, safety procedures, and
emergency response techniques. The seller of the chemical
products used with your machine is responsible for providing the
SDS for that product.
● To learn how to recycle or properly dispose of waste products
generated from service, see your local recycling center or
authorized dealer. If you wish to discard the machine, contact your
local recycling center or authorized dealer.
OUO2005,0000789-19-15FEB20
Machine Cleanout
General Cleaning Guidelines
Machine must be inspected periodically throughout the day. Buildup of
debris must be removed to ensure proper machine function and to
reduce the risk of re. Frequency of these inspections and cleanings
vary depending on a number of factors including operating conditions,
machine conguration, operating speeds, and weather conditions.
Inspections and cleanings may be required multiple times throughout
the day particularly in dry, hot, and windy conditions.
IMPORTANT: Avoid re! Regular and thorough cleaning of
machine combined with other routine maintenance
procedures listed in the Operator’s Manual greatly reduce
the risk of re, downtime, and improve machine
performance.
Besides proper maintenance the condition of the material
being handled is the most signicant factor contributing to
res. Dry, light, and u󰀨y materials that can create a dust
cloud are the most likely to catch re. Debris can
accumulate in various areas especially on horizontal
surfaces. Conditions such as wind speed and direction can
change where the material accumulates. Be aware of these
changing conditions and adjust your cleaning schedule and
practices to ensure proper machine function and to reduce
the risk of re.
Always follow all safety procedures posted on the machine and in the
Operator’s Manual. Before carrying out any inspection or cleaning,
always park machine safely. (See Parking Safely in the Safety
Section).
The entire machine should be inspected, with extra attention given to
the areas noted below.
OUMX068,0001043-19-20JUL20
Cleanout Areas
Primary areas that must be inspected and cleaned on the machine
include (See machine Service Label):
GXT002892—UN—29MAR16
1.Mu󰀪er components (A):
- Exhaust Manifold
- Mu󰀪er Pipes
- Mu󰀪er
- Mu󰀪er Shield
2.Engine cooling ns (B) and intake screens (C).
Machine Cleanout
12