DCY JOHN DEERE AG & TURF DIVISION M158881 B2 Broadcast Spreader LPBS36JD OMM158881 B2 Original Instruction All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reserved to make changes at any time without notice. COPYRIGHT© 2012 Deere & Co. John Deere Ag & Turf Division All rights reserved Previous Editions COPYRIGHT© 2008, 2010 North American Version Litho in U.S.A.
Introduction Table of Contents Introduction................................................................................................ 1 Introduction Product Identification................................................................................. 1 Using Your Operator’s Manual Safety ........................................................................................................ 2 Safety Labels...........................................................................................
Safety • Keep riders off of a towed attachment. Safety • Riders on a towed attachment are subject to injury, such as being struck by objects and being thrown off the attachment during sudden starts, stops and turns. Read Safety in Machine Operator’s Manual Read the general safety operating precautions in your machine operator’s manual for additional safety information. • Riders obstruct the operator's view, resulting in the attachment being used in an unsafe manner.
Safety Labels Safety Labels Understanding The Machine Safety Labels The machine safety labels shown in this section are placed in important areas on your machine to draw attention to potential safety hazards. On your machine safety labels, the words DANGER, WARNING, and CAUTION are used with this safety-alert symbol. DANGER identifies the most serious hazards.
Assembly Parts in Kit Assembly Main Assembly Parts B A C I D G C E F H MX48215 Qty. Description 1 Support Frame, Hopper (A) 1 Hopper Assembly (B) 2 Wheel (C) 1 Handle, Flow Control (D) 1 Gage Plate (E) 1 Tube, Tow (F) Qty.
Assembly Hardware Bag (1008385) J K L M N MX48216 Picture Note: Parts shown above are full size except items J, K, and L. Qty. Description 1 Fan (J) 1 Handle Stop (K) 2 Clevis, Hitch (L) 2 Spacer, 3/8 in. wide for composite (plastic) rim wheels (M) 2 Washer, 5/8 in.
Assembly Hardware Skin Pack (Z-1912) O P R Q S T U V nn oo W pp X Y mm Z bb ii ll gg hh ff aa ee dd kk jj cc MX48217 Picture Note: Parts shown above are full size except items in box. Qty. Description 6 Washer, Flat, 5/8 in.
Assembly Qty. Description 6 Nylon Locknut, 1/4 in. (P) 6 Nylon Washer, Flat, 1/4 in. (Q) 6 Bolt, Hex, 1/4 x 1-3/4 in. (R) 7 Nylon Locknut, 5/16 in. (S) 2 Bolt, Hex, 5/16 x 2-1/4 in. (T) 2 Carriage Bolt, 5/16 x 2 in. (U) 1 O-Ring, 3/8 in. (V) 3 Bolt, Hex, 5/16 x 2-3/4 in. (W) 1 Washer, Curved Spring (X) 1 Carriage Bolt, 5/16 x 3/4 in. (Y) 1 Hitch Pin, 1/2 x 2-1/2 in.
Assembly NOTE: Hardware for the next step is found on the Hardware Skin Pack (Z-1912). NOTE: Hardware for the next step is found on the Hardware Skin Pack (Z-1912). H F D I H G G K MX40300 4. Install tow tube (F) onto support frame (D) with two 5/16 x 2-1/4 in. hex bolts (G) and 5/16 in. hex nuts (H). Tighten nuts to 30 N•m (22 lb-ft), or two complete turns after finger tight. J F Install Transmission and Wheels J F E NOTE: Hardware for the next step is found on the Hardware Skin Pack (Z-1912).
Assembly Composite (Plastic) Wheel Rims IMPORTANT: Avoid damage! The hole in the transmission hub and axle must be closely aligned to prevent large closed-style spring locking pin from binding upon insertion. R H O P S N Q T U MX48213, MX21907 • Install axle bearing (N) onto each side of axle so square end of bearing fits into square hole of support frame assembly (H). • Install 5/8 in. flat washer (O), spacer (P), and two 5/8 in. flat washers (Q) onto each side of axle.
Assembly • Install wheel (P), 5/8 in. flat washer (Q), and E-type snap ring (R) onto each end of axle, as shown in diagram. NOTE: Parts and hardware for the next step are found in the Hardware Bag (1008385) and on the Hardware Skin Pack (Z-1912). NOTE: Delete washers (O), if required, to allow open-style spring locking pin to slip into hole. • Install open-style spring locking pin (S) through inside hole in wheel hub and axle. J H NOTE: Axle has holes on both ends.
Assembly Assemble Gage Plate Attach Flow Control Handle Install Handle Stop NOTE: Rotate link rod (A) as necessary to match diagram. NOTE: Parts and hardware for the next steps are found in Hardware Bag (1008385) and on Hardware Skin Pack (Z-1912). B D B A E F A C B A G MX40578 1. Insert the 'S' shaped end of the link rod (A) through the upper hole of the flow control handle (B). A MX40577 1. Install curved spring washer (A) onto 5/16 x 3/4 in. carriage bolt (B).
Assembly 3. Insert the flow control handle (B) through the gage plate (C). Insure that the link rod (A) is in the up position and end of link rod is orientated as shown. Attach Gage Plate to Spreader 4. Slide the flat grip (D) over the end of the flow control handle (B), as shown. B C A MX40308 1. Hold assembled gage plate (A) over tow tube with flow control handle up and link rod (B) facing hole (C) on the hopper control plate. C B F J E 2.
Installing 2-3/4 in. bolts (E) and two 5/16 in. flat washers (F) through one side of the gage plate, as shown. NOTE: Do not tighten the locknuts until after calibrating the gage plate. 5. Install four pivot plate bushings (G) (two on each side of tow tube (D)), two more 5/16 in. flat washers (F), and secure on opposite side with two 5/ 16 in. nylon locknuts (H). 5. Securely tighten the flow control handle (A) to the gage plate (C), compressing the spring.
Removing control handle to the lock position to open the flow control plate. Removing Directional Control Removing the Spreader Normal Operation (Uniform Spreading) 1. Park machine safely. See “Parking Safely” in the Safety section. 2. Remove all materials from the hopper before removing spreader from machine. Fertilizers, insecticides, and grass seed each have different particle size and weight. This can be referred to as particle density.
Service One Side Only Spreading 2. Lock park brake. 3. Stop engine. 4. Before you leave the operator’s seat, wait for engine and all moving parts to stop. Annual Maintenance E NOTE: There are two different rims of wheels that unit can be shipped with: metal or composite (plastic) wheel rims. Determine wheel rim type and follow appropriate steps below.
Service Remove Gage Plate and Remaining Components Remove Composite (Plastic) Rim Wheels C K E B E B B F D D A G C C F A H MX48213, MX21907 A B B D A B E B D C C F K MX40309 1. Remove two 5/16 x 2-3/4 in. bolts (A), four 5/16 in. flat washers (B), four pivot bushings (C), and two 5/16 in. nylon locknuts (D). Remove assembled gage plate (E) from tow tube (F). I J G MX48212, MX21908 H Picture Note: View from rear of spreader. 1. Remove snap ring (A), 5/8 in.
Troubleshooting J R K K S I F MX40398 3. Remove the transmission bracket (I) from tow tube (F) by removing two 5/16 in. nylon locknuts (J) and two 5/16 in. flat washers (K). W V N U U M T O L MX40400 7. Remove the four bolts (R), washers (S), nuts (T) and straps (U) that hold the gate (V) and directional control plate (W). 8. Separate parts as shown. 9. Clean thoroughly using soap and water.
Specifications lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 2 1.5 Bayer Complete Insect Killer 3 1.5 Bayer Power Force Multi-Insect Killer 2 1 Bayer Power Force Multi-Insect Killer 3 1.5 Bayer Grub Control 2 1.5 Bayer Grub Control 3.2 2 Bayer Lawn Fertilizer Plus Weed Control II 30-3-4 3.8 2 Bayer Season Long Grub Control 2.9 1.5 Bayer Season Long Grub Control 3.6 2 Bayer Lawn Starter Fertilizer 20-27-5 3.
Specifications lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 4.8 2 Ortho Lawn Insect Killer Granules 4 3 Scotts Classic Grass Seed Fall Grass Seed Mix 2.4 1 Ortho Lawn Insect Killer Granules 2 2 Scotts Classic Grass Seed Fall Grass Seed Mix 1.2 1 Ortho Lawn Insect Killer Granules 2.3 1.5 Scotts Grubex 4 2 Ortho Max Insect Killer for Lawns 3.1 2 Scotts Grubex Season Long Grub Control 2 1.
Getting Quality Service Flow Control Setting at 3 mpha Materialsb 3 1.5 Vigoro Ultra Turf Winterizer 22-3-14 3.2 2 Vigoro Weed and Feed Getting Quality Service 4 3 Wal Mart Gardens Kentucky Bluegrass Grass Seed John Deere Quality Continues with Quality Service lbs/1000 square feet lbs/1000 square feet Flow Control Setting 30.3 - 33.4 9 33.5 - 36.
Getting Quality Service Getting Quality Service - 21
Manufacturer Information: Brinly-Hardy Co. 3230 Industrial Pkwy.
CERTIFICATE & DECLARATION OF CONFORMITY FOR CE MARKING Company contact details: Brinly-Hardy Co. 3230 Industrial Pkwy., Jeffersonville, IN 47130, USA Tel: 800-626-5329 Fax: 812-218-6085 Brinly-Hardy Co. declares that their: MCZLPBS36JD0 - Broadcast Spreader is classified within the following EU Directive: Machinery Directive 2006/42/EC and further conform with the following EU Harmonized Standards: EN ISO 12100:2010 EN 14017:2005+A2:2009 Dated: 31 January 2012 Name of signatory: Roger P.
