JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION M158881 H8 Broadcast Spreader LPBS36JD OMM158881 H8 OMM158881 H8 OPERATOR’S MANUAL All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reserved to make changes at any time without notice. COPYRIGHT© 2008 Deere & Co.
INTRODUCTION • Distribute load evenly for safe travel and unloading of cart. Introduction • Do not obstruct the operator’s view during use. Using Your Operator’s Manual Towing Loads Safely Read this entire operator’s manual, especially the safety information, before operating. This manual is an important part of your machine. Keep all manuals in a convenient location so they can be accessed easily.
ASSEMBLY Assembly Parts in Kit Qty. Description 2 Clevis, Hitch (L) Hardware Skin Pack (Z-1912) A M B C K N Qty. Description 1 Grip, Flat (M) 1 Knob, 4-Prong (N) 5 Nylon Locknut, 5/16 in. 2 Nut, Hex, 5/16 in. 6 Nylon Locknut, 1/4 in. 6 Nylon Washer, Flat, 1/4 in. 6 Bolt, Hex, 1/4 x 1-3/4 in. 2 Bolt, Hex, 5/16 x 2-1/4 in. 1 Fan Driver 1 Hairpin Cotter 8 Washer, Flat, 5/16 in. 2 Snap Ring, E-Type 2 Bearing, Axle 6 Washer, Flat, 5/8 in.
ASSEMBLY NOTE: Hardware for the next step is found on the Hardware Skin Pack (Z-1912), Panel A. NOTE: Hardware for the next step is found on the Skin Pack (Z1912), Panel B. A H B F D G C D MX40300 4. Install tow tube (F) onto support frame (D) with two 5/16 x 2-1/4 in. hex bolts (G) and 5/16 in. hex nuts (H). Tighten nuts to 30 N•m (22 lb-ft), or two complete turns after finger tight.
ASSEMBLY NOTE: Hardware for the next step is found on the Hardware Skin ,Pack (Z-1912) Panel D. IMPORTANT: Avoid damage! The hole in the transmission hub and axle must be closely aligned to prevent hairpin cotter from binding upon insertion. I H G M L MX40302, MX21908 K Picture Note: View from rear of spreader. 5. Slide axle until it is centered through transmission as shown in diagram. Install hairpin cotter (L) through transmission and axle center hole (M). This may be a force fit.
ASSEMBLY Install Agitator Spring and Clevis hardware finger tight. NOTE: Hardware for the next step is found on the Hardware Skin Pack (Z-1912), Panel F. 4. Install 1/2 x 2-1/2 in. hitch pin (J) and 1/8 in. hairpin cotter (K) through end of clevis brackets, as shown. 5. Tighten hardware installed in Step 3. Assemble Gage Plate D E Install Handle Stop NOTE: Parts and hardware for the next steps are found in Hardware Bag (Z-1911) and on Hardware Bag (Z-1912), Panel H. B C A D B A E F C MX40576 1.
ASSEMBLY Attach Flow Control Handle 3. Insert the flow control handle (B) through the gage plate (C). Insure that the link rod (A) is in the up position and end of link rod is orientated as shown. NOTE: Rotate link rod (A) as necessary to match diagram. 4. Slide the flat grip (D) over the end of the flow control handle (B), as shown. B A B C A B F J E K MX40578 1. Insert the 'S' shaped end of the link rod (A) through the upper hole of the flow control handle (B). A C H I D G G MX40579 5.
ASSEMBLY 2-3/4 in. bolts (E) and two 5/16 in. flat washers (F) through one side of the gage plate, as shown(A). Attach Gage Plate to Spreader NOTE: Do not tighten the locknuts until after calibrating the gage plate. B 5. Install four pivot plate bushings (G) (two on each side of tow tube (D)), two more 5/16 in. flat washers (F), and secure on opposite side with two 5/ 16 in. hex locknuts (H). Calibrate Gage Plate C B A MX40308 1.
INSTALLING 5. Securely tighten the flow control handle (A) to the gage plate (C), compressing the spring. Flow control handle should have resistance to movement. Removing Removing the Spreader Fan Height Adjustment NOTE: The four tabs on the fan should be compressed against the fan driver. If pressure is not applied, the fan connection will be loose resulting in poor performance. 1. Park machine safely. See “Parking Safely” in the Safety section. 2.
SERVICE Directional Control One Side Only Spreading Normal Operation (Uniform Spreading) Fertilizers, insecticides, and grass seed each have different particle size and weight. This can be referred to as particle density. As the particles are impacted by the fan, the distribution can be centered or slightly off center depending on particle density and forward vehicle speed. E F C A D A MX40395 MX25911 Adjustment can be made by moving the direction control plate (A) to the right or left.
SERVICE Annual Maintenance Remove Gage Plate and Remaining Components Remove Wheels E B B C D E C C F A A D F B A B MX40396 B 1. Remove E-type snap ring (A), 5/8 in. flat washer (B), wheel (C), 5/8 in. flat washer (D) (if installed), and axle bearing (E). Remove hairpin cotter, special (F). D A B E B D C C F K MX40309 1. Remove two 5/16 x 2-3/4 in. hex bolts (A), four 5/16 in. flat washers (B), four pivot plate bushings (C), and two 5/16 in. nylon locknuts (D).
TROUBLESHOOTING J R K K S I F MX40398 3. Remove the transmission bracket (I) from tow tube (F) by removing two 5/16 in. nylon locknuts (J) and two 5/16 in. flat washers (K). W V N U U M T O L MX40400 7. Remove the four bolts (R), washers (S), nuts (T) and straps (U) that hold the gate (V) and directional control plate (W). 8. Separate parts as shown. 9. Clean thoroughly using soap and water.
SPECIFICATIONS lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 2 1.5 Bayer Grub Control 3.2 2 Bayer Lawn Fertilizer Plus Weed Control II 30-3-4 3.8 2 Bayer Season Long Grub Control 2.9 1.5 Bayer Season Long Grub Control 3.6 2 Bayer Lawn Starter Fertilizer 20-27-5 3.2 2 Bayer Lawn Fertilizer Plus Crabgrass Preventer 30-3-4 LPBS36JD Broadcast Spreader 3 2 Eliminator Ant, Flea, and Tick Killer Granules Dimensions 2.5 1.
SPECIFICATIONS lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb lbs/1000 square feet Flow Control Setting at 3 mpha Materialsb 2 1.5 Ortho Max Insect Killer for Lawns 2.3 2 Scotts Grubex Season Long Grub Control 1 1 Ortho Max Insect Killer for Lawns 1.4 1.5 Scotts Lawn Fungus Control 10 3 Parkers Super Soilife Lawn and Garden Fertilizer 10-10-10 2.7 2 Scotts Lawn Fungus Control 2.2 2 Scotts Pure Premium Kentucky Bluegrass Mix 6.
GETTING QUALITY SERVICE lbs/1000 square feet 2 Flow Control Setting at 3 mpha Materialsb 2 Wal Mart Gardens Kentucky Bluegrass Grass Seed Getting Quality Service John Deere Quality Continues with Quality Service 8 4 Wal Mart Gardens Kentucky 31 Tall Fescue 4 3 Wal Mart Gardens Kentucky 31 Tall Fescue 3.2 2 Wal Mart Weed and Feed 28-3-3 a. Flow Control Settings are based on 3 mph forward speed.
GETTING QUALITY SERVICE Getting Quality Service - 15
