JLBICH602 built-in ceramic hob Instruction manual
Important Safety Information 1 It is most important that this instruction manual should be retained with the appliance for future refer- ence. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings have been provided in the interest of safety.
Contents For the User For the Installer Important Safety Information - - - - - - Description of the Appliance - - - - - - The Control Panel - - - - - - - - - - - - - - 2 Installation - - - - - - - - - - - - - - - - - - - 5 4 Technical Data - - - - - - - - - - - - - - - - - - - 5 9 9 Electrical Connection - - - - - - - - - - - - - - - - 5 Touch Control sensor fields - - - - - - - - - - - - - Electrical Requirements - - - - - - - - - - - - - - - 5 Displays - - - - - - - - - - - - - - - - - - - -
Description of the Appliance Cooking surface layout Single cooking zone 1200W Single cooking zone 2300W 4 Single cooking zone 1800W Control panel Single cooking zone 1200W
Installation Technical Data Cooking rings Appliance dimensions Width Depth Height 590 mm 520 mm 47 mm Position Front left Rear left Rear right Front right Diameter 210mm 145mm 180mm 145mm Connection voltage Power 2300W 1200W 1800W 1200W 230 V ~ 50Hz Worktop cut-out dimensions Maximum connected load power Width Depth 5,8kW 560 mm 490 mm Electrical Connection 1 This hob must be earthed. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E.
Building In 1 The hob must be installed according to the in- structions supplied by qualified and competent personnel to the relevant National Standards. Building In • The dimensions of the cut-out section and recess required must be as shown in the relevant diagrams. • Proper arrangements must be made of a continuous supply of air to the hob to prevent overheating. 6 • Clean the worktop in the area of the cut-out section.
The Control Panel Cooking zones and heat setting selection Display On/Off Touch Control sensor fields The appliance is operated using the Touch Control sensor fields. Functions are controlled by touching sensor fields and confirmed by displays. Touch the sensor fields from above, without covering other sensor fields.
Residual heat indicator 1 Warning! Risk of burns from residual heat. After being switched off, the cooking zones need some time to cool down. Look at the residual heat indicator h . 3 Residual heat can be used for melting and keeping food warm.
Using the child safety device The child safety device prevents unintentional use of the appliance. Setting the child safety device Step 1. Control panel Switch on appliance (Do not set a heat setting) 2. Touch of the front right cooking zone and the same time 3. Touch of the front right cooking zone Display ¾ / h (if hot) at 4 x ¾ or h Decimal points flash l Appliance switches off.
Safety cut-out Cooking surface • If after switching on the appliance a heat setting is not set for a cooking zone within approx. 10 seconds, the appliance automatically switches itself off. • If one or more sensor fields are touched for longer than approx. 10 seconds, the cooking surface is automatically switched off. ER03 flashes on the display or changes to h if there is still residual heat. • If all cooking zones are switched off, the cooking surface automatically switches itself off after approx.
When the hob is first installed 1 Remove all packaging, both inside and outside the hob including the advertising labels and any protective film, before using the hob. 3 When a cooking zone is switched on, it may hum briefly. This is a characteristic of all ceramic glass cooking zones and does not impair either the function or the life of the appliance.
Hints and Tips on cooking and frying Cookware • You can recognise good cookware from the bottoms of the pans. The bottom should be as thick and flat as possible. • Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolourations on the ceramic glass surface which can be impossible to remove. Energy saving 2 2 2 2 14 Always place cookware on the cooking zone before it is switched on. If possible, always place lids on the pans.
Cooking chart 3 This chart is intended as a guide only. It may be nec- essary to increase or decrease the temperature to suit your individual requirements. Only experience will enable you to determine the correct setting for your personal requirements. Heat setting Cooking process suitable for Cooking time Notes Residual heat setting, Off position 0 Keeping food warm Keeping cooked foods warm as required Cover Melting Hollandaise sauce, melting butter, chocolate, gelatine 5-25 mins.
Cleaning the hob 1 Warning! Risk of burns from residual heat. 1 Important Sharp objects and abrasive cleaning materials will damage the appliance. Clean with water and washing up liquid. 1 Important Residues from cleaning agents will damage the appliance. Remove residues with water and washing up liquid. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. 2. Rub the appliance dry using a clean cloth. Removing deposits 1.
Something not working If the hob is not working correctly, please carry out the following checks, before contacting your local Service Force repair agent. In the event of any other fault codes that arise, disconnect the appliance from the electrical supply for a few seconds (take out the fuse from the housing wiring system). If the fault code is displayed again, please call your local Service Force repair agent and report the fault code.
Repairs - After Sales Service If your hob is not performing satisfactorily; consult the fault finding guide within this instruction book (Something not working). In the event of a fault occurring which you cannot resolve yourself from advice given within this instruction manual your first step is to contact our extended warranty administrators on 0870 0107887 who will give you details for your local Service Force. When contacting Service Force, please quote the model (Mod.) and serial number (S.N.
Rating Plates JLBICH602 PEE2019 949 591 900 230 V 50 Hz 6,5 kW John Lewis JLBICH602 PEE2019 949 592 457 230 V 50 Hz 6,5 kW John Lewis 19
John Lewis Partnership 171 Victoria Street London SW1E 5NN www. johnlewis.
