JLBIHD907 built-in cooker hood Instruction manual
Important Safety Information It is most important that this instruction manual should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings ha ve been pr ovided in the inter est of saf ety .
Contents For the User Important Safety Information For the Installer 2 Electrical Connections 8 Description of the Appliance 4 Electrical Requirements Electrical Connection 8 8 Using the cooker hood 9 Installing the Cooker Hood 5 Installation Requirements Unpacking Fitting the Wall Brackets Fitting the Canopy Hood Extraction Recirculation 5 5 6 6 7 7 Cooker Hood Controls To Operate Recirculation Extraction 9 10 10 10 Maintenance and Cleaning 11 External Cleaning Cleaning the Ducting panels
Description of the Appliance 4
Installation Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas.
Installing the Cooker Hood Fitting the Wall Brackets 200 200 11a 1 1 2 960 180 180 2 250 362 • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. • Draw a horizontal line at 960 mm above the hob. • Mark a point (1) on the horizontal line, 200 mm to the right of the vertical reference line. • Repeat this operation on the other side, checking that the two marks are level.
Extraction (Ducted) The cooker hood is more effective when installed in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be evacuated through an outside vent of ø125 (5ins) or ø150mm (6ins). The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. When the cooker hood is ducted to the outside the charcoal filter must be removed.
Electrical Connections THIS APPLIANCE MUST BE EARTHED Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC).
Using the cooker hood The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Cooker Hood Controls The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. KEY LED L Turns lighting on and off. L First speed. When pressed for about 1 seconds the motor is switched off.
To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack. Extraction In the extraction mode the contaminated air enters the cooker hood passing through the grease filters and is passed out through the ducting into the atmosphere.
Maintenance and Cleaning Before carrying out any maintenance or leaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel. Cleaning the Ducting panels • Open the ducting panels.
Alarm signal reset • Stop the motor and switch off the lights. • Press button T3 for at least 3 seconds, until the leds start to flash. Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. This charcoal filters cannot be washed or regenerated, and must be replaced when the led S1 starts to flash, or at least once every 4 months.
• Close the ducting panels. Reset the alarm signal • Stop the motor and switch off the lights. • Press button T3 for at least 3 seconds, until the leds start to flash. This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Changing the Halogen Spot Lamp • Remove the light cover by unfastening the screws that hold it. • Remove the lamp from the holder by pulling the lamp downwards.
Something not Working If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force agent. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom Solution The cooker hood will not start • Check the hood is connected to the electricity supply. • Make sure the switch is in the ‘ON’ position.
John Lewis Partnership 171 Victoria Street London SW1E 5NN www.johnlewis.
