Washer Dryer JLWD1614 User Manual
Contents Safety information Children and vulnerable people safety General Safety Safety instructions Installation Electrical Connection Water Connection Use Service Disposal Installation Unpacking Information for installation Installation on suspended flooring Product description Appliance overview Control panel Control panel description Display Dial and buttons Introduction On/Off Temp Spin Mode - Wash Prewash Permanent Extra Rinse Stain Permanent Soft Plus Reduce time Child Lock Mode - Dry Permanent Anti
Stubborn stains Detergents and other treatments Ecological hints Water hardness Drying hints Items not suitable for drying Garment labels Drying cycle duration Additional drying General Tips Care and cleaning External cleaning Descaling Maintenance wash Door seal Cleaning the drum Cleaning the detergent dispenser 41 41 41 42 42 42 42 42 42 42 43 43 43 43 43 43 44 Cleaning the drain pump 44 Cleaning the inlet hose and the valve filter 46 Emergency drain 47 Frost precautions 47 Troubleshooting 48 Introducti
Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. Children and vulnerable people safety Warning! Risk of suffocation, injury or permanent disability.
General Safety • • • • • • • • • • • Do not change the specification of this appliance. This appliance is intended to be used in household and similar applications such as: – staff kitchen areas in shops, offices and other working environments; – by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes.
• • • • • • • • • • • • • • 6 The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Wipe away lint or packaging debris that has accumulated around the appliance.
• Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.
Safety instructions Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance. • Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather. • Always keep the appliance vertical when it is being moved. • Make sure that there is air circulation between the appliance and the floor. • Remove all the packaging and the transit bolts.
• If laundry has been washed with a stain remover, carry out an additional rinse cycle before starting a drying cycle. • Make sure that all metal objects are removed from the laundry. • Only dry fabrics that are suitable to dry in the washer dryer. Follow the cleaning instruction on the item label. • Plastic items are not heat resistant. – If a detergent ball is used, remove it before starting a drying programme. – Do not use a detergent ball if setting a nonstop programme.
Installation Warning! Refer to Safety chapters. Unpacking 1. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top and the polystyrene packaging materials. 3. Open the door. Remove all the items from the drum . 4. Put the front polystyrene packaging element on the floor under the appliance. Carefully put down the appliance onto its rear side.
5. Remove the polystyrene protection from the bottom. Put the appliance back into an upright position. 6. Remove the power supply cable and the drain hose from the hose holders. 1 2 7. Remove the three transit bolts and pull out the plastic spacers. We recommend that you keep the packaging and the transit bolts for any transport of the appliance.
1. Connect the water inlet hose to the back of the appliance. 45 20 2. On the edge of a sink - Fasten the guide to the water tap or to the wall. O O 2. Position it toward left or right depending on the positon of the water tap. Make sure that the inlet hose is not in vertical position. 3. If necessary, loosen the ring nut to set it in the correct position. 4. Connect the water inlet hose to the cold water tap with 3/4'' thread.
illustration. Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration. To limit vibration we recommend placing a waterproof wooden panel, at least 15 mm thick, under the appliance. It should be screwed to at least 2 floor beams and should extend beyond the front feet. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm - min. 1.5") must be larger than the external diameter of the drain hose.
Product description Appliance overview 1 2 8 3 9 10 4 5 11 12 6 7 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Control panel Control panel description 1 2 3 14 The permanent options are set by holding pressed the relative button for at least 3 seconds. 1. 2. 3. 4. 5. 6. 7. 8. Programme dial Spin touch button Temp touch button Display Time dry touch button Auto dry touch button Start/Pause touch button Delay start touch button Washer Dryer User Manual 4 13 12 11 5 6 10 7 9 8 9. Mode - Dry touch button and permanent Anticrease option 10. Reduce time touch button and permanent Child Lock option 11.
Display The Temperature area: Temperature indicator . Cold water indicator. Door locked indicator. Child safety lock indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. • Cycle end ( • Warning code (e.g. • Error indicator ( , washing and/or drying phase). ). ). ). ). Time Manager indicator. Time dry indicator. Steam phase indicator.
Washing phase indicator Extra Rinse indicator. Soft Plus indicator. Drum clean indicator. This is a recommendation to perform the drum cleaning. Anti-crease phase indicator. Drying phase indicator. The spin area: Spin speed indicator No Spin indicator. Spin phase is off. Rinse Hold indicator. Maximum load indicator (refer to "The SensiCare System load detection " paragraph). It flashes when the laundry load exceeds the maximum declared load of the selected programme. Add garments indicator.
Dial and buttons Introduction Spin The options/functions are not available with all washing programmes. Check the compatibility between options/ functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allow you to set incompatible options/functions. On/Off Press this button for a few seconds to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off.
Prewash Permanent Soft Plus With this option you can add a prewash phase to a washing programme. Set this option to optimise the fabric softener distribution and improve fabric softness. The corresponding indicator above the touch button illuminates. Recommended when you use fabric softener. • Use this option to add a pre-wash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust, mud and other solid particles.
Synthetics Cotton 1) Cotton Eco Permanent Anti-crease indicator ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ This option adds a short anti-crease phase at the end of the programme. This phase reduces fabric creasing and facilitates the fabric ironing. To activate/deactivate this option, hold the Mode - Dry button pressed for 3 seconds until comes on/goes off on the the indicator display.
Delay start With this option you can delay the start of a programme to a more convenient time. Touch the button repeatedly to set the required delay. The time increases in steps of 1 hour up to 20 hours. The corresponding indicator above the touch button illuminates. The display shows the selected delay time. After touching the Start/Pause button, the appliance begins the countdown and the door is locked.
Programmes Programme Chart Programme Default temperature Temperature range Reference spin speed Spin speed range Maximum load Programme description (Type of load and soil level) Washing programmes Cotton 40 °C 90 °C - Cold 1600 rpm (1600- 400 rpm) 8 kg White cotton and coloured cotton. Normal, heavy and light soil. Cotton Eco1) 40 °C 60 °C - 40 °C 1600 rpm (1600- 400 rpm) 8 kg White cotton and fast-coloured cotton. Normal soil.
Programme Default temperature Temperature range Reference spin speed Spin speed range Steam refresh Maximum load 1 kg Programme description (Type of load and soil level) Cottons, Synthetics, Delicates. Short and gentle steam programme to refresh even your very delicate garments, including very delicate garments with sequins, lace etc. When treating smaller loads, the programme duration can be further reduced by means of the Reduce time option.
Programme Default temperature Temperature range Reference spin speed Spin speed range Maximum load Programme description (Type of load and soil level) Anti-allergy 60 °C 1600 rpm (1600 - 400 rpm) 8 kg White cotton items. This programme removes micro-organisms thanks to a washing phase with the temperature maintained above 60°C for several minutes. This helps remove germs, bacteria, micro-organism and particles.
Programme Default temperature Temperature range Reference spin speed Spin speed range Maximum load Programme description (Type of load and soil level) Reset position. The display shows dashes only. 1) Cottons energy saving programme. This programme at 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with 96/60/EC Directive. Set this programme to have a good washing results and decrease the energy consumption.
Delay start Reduce time Stainether. 2) Prewash1) No Spin Spin Programme ■ 1h wash & dry 1kg ■ 1) Prewash and Stain cannot be selected together. 2) This option is not available with temperature lower than 40 °C. 3) If you set the No Spin option, the appliance performs draining only.
Dryness Level Iron Dry Suitable for ironing Type of fabric Load Cottons and Linen (sheets, tablecloths, shirts, etc) up to 4 kg 1) Also available with Anti-allergy and Cotton Eco programme. 2) Hints for test institute The test performance, in accordance with EN 50229, must be carried out with a FIRST drying load of the maximum declared drying capacity (load composition according to EN61121) by setting the AUTOMATIC CUPBOARD DRY for Cotton Eco programme.
Dryness Level Type of fabric Iron Dry Suitable for ironing Cottons and Linen (sheets, tablecloths, shirts, etc) 28 Load (kg) Spin speed (rpm) Suggested duration (mins) 4 1600 100 - 120 2 1600 60 - 80 1 1600 40 - 50 Washer Dryer User Manual
Settings Acoustic signals This appliance has different acoustic signals, that operate when: • You activate the appliance (special short tune). • You deactivate the appliance (special short tune). • You touch the buttons (click sound). • You make an invalid selection (3 short sounds). • The programme is completed (sequence of sounds for about 2 minutes). • The appliance has a malfunction (sequence of short sounds for about 5 minutes).
Before first use 1. Make sure that the electrical power is available and the water tap is open. 2. Pour 2 litres of water into the detergent compartment marked by . This action activates the drain system. 3. Pour a small quantity of detergent into the compartment marked by . 4. Set and start a programme for cotton at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub.
Daily Use - Washing only Washing heavily oiled, greasy stains could cause damage to rubber parts of the washing machine. Warning! Refer to Safety chapters. Activating the appliance 1. Connect the mains plug to the mains socket. 2. Open the water tap. 3. Press the On/Off button for a few seconds to activate the appliance. Filling the detergent and additives A short tune sounds. Loading the laundry 1. Open the appliance door. 2. Shake the items before you put them in the appliance. 3.
Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. • Do not exceed to liquid detergent dose indicated on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser.
The programme starts, the door is locked. The display shows the indicator . The drain pump can operate shortly before the appliance fills water. Starting a programme with the delay start 1. Touch the Delay start button repeatedly until the display shows the desired delay time. The button indicator illuminates. 2. Touch the Start/Pause button. The appliance door locks and starts the countdown of the delay start. The display shows the indicator .
1. Touch the button Start/Pause. The related indicator flashes. 2. Change the options. The given information in the display changes accordingly. 3. Touch the button Start/Pause again. The washing programme continues. Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance.
• You must drain the water to open the door: 1. If necessary, touch the Spin button to decrease the spin speed proposed by the appliance. 2. Press the Start/Pause button: the appliance drains the water and spins. The option indicator Rinse Hold disappears. If you have selected No Spin , the appliance will only drain the water. 3. When the programme is completed and the goes off, you can door locked indicator open the door. 4. Press the On/Off button for a few seconds to deactivate the appliance.
Daily use - Washing & Drying Warning! Refer to Safety chapters. Washing and Drying Automatic levels This appliance is an automatic washer dryer. 1. Tap on the Auto dry button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: NON-STOP programme Wash and dry Not all programmes are compatible with drying function. The 1h wash & dry 1kg programme is already a complete wash&dry programme.
In the display the door locked indicator comes on. The display also shows the remaining programme time. At the end of the drying programme • The appliance stops automatically. • The acoustic signals operate (if they are active). • In the display comes on. • The indicator of button Start/Pause goes off. The door locked goes off. The appliance continues to operate with the anti-crease phase for approximately 30 minutes or more if Anti-crease option was set. The anti-crease phase reduces creasing.
Daily use - Drying only Warning! Refer to Safety chapters. This appliance is an automatic washer dryer. Preparation to drying 1. Press the On/Off button for some seconds to activate the appliance. 2. Load the laundry one item at a time. 3. Turn the programme dial to the programme suitable for the items to dry. The appliance defaults to the washing only mode and the indicator of the Mode - Wash button is on. 4. Tap on the Mode - Dry button and then on the Mode - Wash button to perform drying only.
You can remove the laundry before the anticrease phase is completed. We recommend, for better results, that you remove the laundry when the phase is almost completed or completed. The indicator remains lit. • Press the On/Off button for some seconds to deactivate the appliance. After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically. 1. Remove the laundry from the appliance. 2. Make sure that the drum is empty.
Fluff in the fabrics During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff. The released fluff could stick to the fabrics during the next cycle. This inconvenient increases with technical fabrics. To prevent the fluff in your laundry, we recommend that you: • To do not wash dark fabrics after you washed and dried light coloured fabrics (hand towel, wool, sweatshirt ) and the contrary.
Hints and tips Warning! Refer to Safety chapters. The laundry load • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the laundry care labels. • Do not wash white and coloured items together. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty pockets and unfold.
• If you pre-treat the stains or use a stain remover, set a programme with a low temperature. • To use the correct quantity of detergent, check the water hardness of your domestic system. Refer to "Water hardness". Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener.
Care and cleaning Warning! Refer to Safety chapters. External cleaning Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. Caution! Do not use alcohol, solvents or chemical products. the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and clean the inner part of the appliance, run a maintenance wash regularly (at least once a month). Refer to Cleaning the drum chapter.
• Run the Machine clean programme . For more details, refer to washing programme table. 3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess. Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”.
Warning! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 1. Open the pump cover. 2 1 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 2. Place a suitable bowl below the drain pump access to collect the water that flows out.
10. Clean the filter under the water tap. 12. Close the pump cover. 2 1 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water.
45° 20° Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: Warning! Make sure that the temperature is higher than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 1.
Troubleshooting Warning! Refer to Safety chapters. Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The mains supply is unstable. Wait until the mains supply is stable.
If the appliance is overloaded, remove some items from the drum and/or hold the door shut while touching the Start/Pause button until the indicator stops flashing (see the picture below). Warning! Deactivate the appliance before carrying out any check. Possible failures Problem Possible solution • • • • The programme does not start. • • • • • The appliance does not fill with water properly.
Problem The appliance does not drain the water. The spin phase does not operate or the washing cycle lasts longer than usual. There is water on the floor. Possible solution • • • • • Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. Make sure that the connection of the drain hose is correct. Set the drain programme if you set a programme without drain phase. Set the drain programme if you set an option which ends with water in the tub.
Problem After the washing cycle, there are some detergent residues in the dispenser drawer. The appliance does not dry or does not dry correctly. The laundry is full of different colours fluff. Possible solution • • • • • • Make sure that the flap is in the correct position (UP for powder detergent - DOWN for liquid detergent). Make sure you have used the detergent dispenser according the indications given in this user manual. Turn the water tap on. Make sure the drain filter is not clogged.
5. Take out the laundry and then close the appliance door. 6. Close the filter flap.
Consumption values Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration. Technical specifications may be changed without prior notice to improve the quality of product.
Technical Data Dimension Width/ Height/ Depth/ Total depth 597 mm/ 848 mm/ 547 mm/ 576 mm Electrical connection Voltage Overall power Fuse Frequency 230-240 V 2200 W 13 A 50 Hz Level of protection against ingress of solid particles and moisture IPX4 ensured by the protective cover, except where the low voltage equipment has no protection against moisture Cold water Water supply 1) Water supply pressure 2) Minimum Maximum 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Maximum wash load Cotton 8 kg Maximum
Accessories Available in www.electrolux.com/shop or from authorised dealer Only appropriate accessories approved by John Lewis ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. Fixing plate kit (4055171146) Available from your authorised dealer. Read carefully the instructions supplied with the accessory. If you install the appliance on a plinth, secure the appliance in the fixing plates.
Repairs - after sales service Your John Lewis appliance comes with a three year guarantee. Your original receipt acts as your guarantee. Please make sure you retain it. The guarantee does not cover you against faults caused by accidental damage or misuse. For further details visit johnlewis.com/customerservices. If it is not working correctly refer to the "Troubleshooting" chapter in this user manual.
John Lewis, Southampton 02380 216 400 Knight & Lee, Southsea 02392 827 511 John Lewis, Stratford 020 8532 3500 John Lewis, The Trafford Centre 0161 491 4040 John Lewis, Watford 01923 244 266 John Lewis, Welwyn 01707 323 456 John Lewis at home John Lewis, Ashford 01233 811 010 John Lewis, Chester 01244 393 880 Washer Dryer User Manual John Lewis, Chichester 01243 813 030 John Lewis, Croydon 020 8662 4730 John Lewis, Horsham 01403 214 740 John Lewis, Ipswich 01473 275 850 John Lewis, Newbury 01635 263 980 J
Environmental concerns marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances.
Washer Dryer User Manual 59
157017060-B-252018 ( Subject to change without notice.
