Washing Machine JLWM 1205 JLWM 1412 User manual
Contents Safety information 3 Programmes 18 Children and vulnerable people safety General Safety Safety instructions 3 3 5 Consumption values 21 Technical data 22 Installation 5 Care and cleaning 23 23 23 23 24 24 24 25 26 26 28 29 30 30 30 30 31 32 33 On Off button 1 Programme knob 2 Display 3 Start/Pause button 4 Delay start button 5 Quick button 6 Extra rinse button 7 Spin button 8 Temperature button 9 Personalization 8 8 9 9 9 10 10 10 10 11 Descaling External cleaning Detergent dispens
Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. Children and vulnerable people safety Warning! Risk of suffocation, injury or permanent disability.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused.
Safety instructions Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance. • Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
• Use this appliance in a household environment. • Obey the safety instructions on the detergent packaging. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Do not touch the glass of the door while a programme operates. The glass can be hot. • Make sure that you remove all metal objects from the laundry. • Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure which accessories can be used.
Product description 1 2 3 4 5 6 7 1. 2. 3. 4. Worktop Detergent dispenser Control panel Door handle 5. 6. 7. Rating plate Drain pump Feet for the appliance level Accessories 1. 2. 3. 1 2 4 3 Spanner To remove the transit bolts. Plastic hose guide To connect the drain hose on the edge of a sink. Plastic caps Washing Machine user manual 4. To close the holes on the rear side of the cabinet after the removal of the transit bolts. Inlet hose To connect the appliance to the cold water tap.
Control panel The Control Panel illustrated below shows the programme selector dial as well as the buttons and pilot lights. These are represented by relevant numbers on the following pages. 1 2 Cottons economy Reset 20 Minute wash 3 Cottons with Prewash Intensive Heavy cotton Mix 20° Synthetics Rinse Easy iron Drain Delicates Spin Wool On / Off 95° 1400 60° 1200 40° 800 30° 400 Rinse Hold Cold Temperature Child safety Spin 9 8 1. 2. 3. 4. 5. 6. 7. 8. 9.
Display 3 A B C The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme.
Quick button 6 Press the button 6 to decrease the programme duration. • Press once to set 'Shortened duration' for items with daily soil. • Press twice to set 'Extra Quick' for items with almost no soil. Some programmes accept only one of the two functions. Extra rinse button 7 Press button 7 to add extra rinse to a programme. Use this function for persons allergic to detergents and in areas where the water is soft.
Personalization Acoustic signals function Permanent extra rinse function You can hear the acoustic signals when: • You activate the appliance. • You deactivate the appliance. • You press the buttons. • The programme is completed. • The appliance has a malfunction. To deactivate/activate the acoustic signals, press the Temperature button and the Spin button at the same time for 6 seconds. With this function you can keep the extra rinse function permanently on when you set a new programme.
Use First use 1. 2. To activate the drain system, put 2 litres of water in the main wash compartment of the detergent dispenser. Put a small quantity of detergent in the main wash compartment of the detergent dispenser. Set and start a programme for cotton at the highest temperature without laundry. This removes all possible dirt from the drum and the tub. Daily use 1. 2. 3. 4. 5. 6. Open the water tap. Connect the mains plug to the mains socket. Press button 1 to activate the appliance.
• • • • : Detergent compartment for the washing phase. If you use a liquid detergent, put it in immediately before you start the programme. : Liquid additives compartment (fabric conditioner, starch). Put the liquid in the compartment before you start the programme. : Maximum level for the quantity of liquid additives. 4. To use liquid detergent, turn the flap down. Flap for powder or liquid detergent. Turn it (up or down) in the correct position to use powder or liquid detergent.
4. 5. Set the available functions and the delay start. When you press the relevant button, the indicator of the set function comes on or the display shows the related symbol. Press button 4 to start the programme. The indicator of button 4 is on with red colour. Set the delay start 1. 2. The drain pump can operate for a short time when the appliance fills water.
Important! If you deactivate the appliance, it is necessary to set the programme again. The appliance drains and spins automatically after approximately 18 hours. End of programme • The appliance stops automatically. • The acoustic signals operate. • In the display comes on. • The indicator of the Start/Pause button 4 goes off. • The door lock symbol goes off. • Press button 1 to deactivate the appliance.
Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Before loading the laundry Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash. New coloured items may run in the first wash; they should therefore be washed separately the first time. Make sure that no metal objects are left in the laundry (e.g.
Degrees of water hardness Water hardness is classified in so-called “degrees” of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority. If the water hardness degree is medium or high we suggest you to add a water softener following always the manufacturer’s instructions. When the degree of hardness is soft, readjust the quantity of the detergent.
Programmes Programme Temperature Type of load max. weight of load Cycle description Functions Cottons 95° - Cold White and coloured cotton with normal soil. max. 7 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD EXTRA RINSE QUICK1) with Prewash 95° - Cold White and coloured cotton with heavy soil. max. 7 kg Prewash Wash Rinses Long spin SPIN REDUCTION RINSE HOLD EXTRA RINSE QUICK1) Intensive 95° - 40° White and coloured cotton with heavy soil. max.
Programme Temperature Type of load max. weight of load Cycle description Functions Drain All fabrics The maximum load of the laundry is related to the type of laundry. Drainage of the water Rinse Cold All fabrics. One rinse with additive spin phase SPIN REDUCTION RINSE HOLD EXTRA RINSE4) Mix 20°5) 20° Special programme for cotton, synthetic and mixed fabrics with light soil. Set this programme to decrease the energy consumption.
6) Standard programmes for the Energy Label consumption values according to regulation 1061/2010, the ‘Cottons Economy 60° C’ and “Cottons Economy 40° C” are respectively the “standard 60° C cotton programme” and the “standard 40° C cotton programme”. They are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry. The water temperature of the washing phase may differ from the temperature declared for the selected programme.
Consumption values At programme start the display shows the duration programme for the maximum load capacity. During the washing phase the programme duration is automatically calculated and can greatly be reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; real load 1 kg, the programme duration don’t reach 1 hour). When the appliance is calculating the real programme duration a dot blinks in the display.
Technical data Dimensions Width Height Depth Depth (Overall dimensions) 60 cm 85 cm 52,2 cm 54 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door.
Care and cleaning You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits.
6. Put back the dispenser in the recess. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The display shows an alarm code because of the problem with water drain. Warning! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot.
8. 9. Clean the filter under the water tap and put it back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 1 4. 5. When the container is full of water, put the drainage duct back again and empty the container. Do steps 3 and 4 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. 1 6. 2 10. Close the drain pump door. 2 Remove fluff and objects from the pump.
3. 1 2 3 4. 5. Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. If necessary, wait until the water has cooled down; 4. Open the pump door; 5. Place a container on the floor below the recess of the drain pump; 6. Press the two levers and pull forward the drainage duct to let the water flow out; 7. When the container is full of water, put the drainage duct back again and empty the container; Repeat this operation until water stops flowing out; 8.
Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures.
Unpacking 1. 2. 3. 4. Use the gloves. Remove the external film. If necessary, use a cutter. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Remove the cardboard top. Remove the polystyrene packaging materials. Remove the internal film. 1 2 5. 28 Open the door.
We recommend that you keep the packaging and the transit bolts for when you move the appliance. Positioning and levelling 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
Caution! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. Fixing plate kit (4055171146) Available from your authorized dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Follow the instructions supplied with the kit. 20 O 45 O Plumbing in Your new washing machine has been designed to be permanently plumbed in to your home’s water supply and drainage system.
Min. 90 cm (35.4”) 3 pin Min. 60 cm (23.6”) Warning! The appliance should NOT be placed on deep pile carpeting. Note! Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown. Water drainage This appliance is designed to be permanently plumbed into your home's drainage system using one of the following methods. 1. Into a drainage standpipe Firstly form a hook in the end of the drain hose using the “U” piece” supplied.
In the interest of the environment The appliance should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority.
What to do if… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below. Important! if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Problem Possible cause Close the door correctly. The appliance door is open or not closed correctly. The spin phase does not operate. The programme does not start. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in Put in the mains plug.
Problem Possible cause Possible solution The washing results are not satisfactory. The detergent you used was not sufficient or correct. Increase the detergent quantity or use a different one. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance.
Repairs - After Sales Service Your appliance comes with a three year warranty. If it is not working correctly; consult the fault finding guides within this instruction book ("What to do if ..."). If a fault occurs which you can not resolve through following the advice and information contained within this instruction manual, the next step is to contact our extended warranty administrators on: 0844 871 7771 They will give you details for your local Service engineer.
Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
John Lewis, Oxford Street 020 7629 7711 John Lewis, Norwich 01603 660021 Peter Jones, Sloane Square 020 7730 3434 John Lewis, Nottingham 0115 941 8282 John Lewis, Brent Cross 020 8202 6535 John Lewis, Peterborough 01733 344644 John Lewis, Kingston 020 8547 3000 John Lewis at home, Poole 01202 756020 John Lewis, Aberdeen 01224 625000 John Lewis, Reading 0118 957 5955 John Lewis, Bluewater 01322 624123 John Lewis, Sheffield 0114 276 8511 John Lewis, Cambridge 01223 361292 John Lewis, Solihull 012
Washing Machine user manual 39
132912540-A-252013
