Installation Instructions 12in. Deep Premier Closet Organizer MODEL: JLH-528, JLH-529 16in. Deep Deluxe Closet Organizer MODEL: JLH-525, JLH-526 www.johnlouishome.
IMPORTANT: DO NOT RETURN TO STORE! For missing or damaged parts, technical or assembly questions, please call John Louis Customer Service at 1-800-480-6985 IMPORTANTE: ¡NO LO DEVUELVA A LA TIENDA! Llame al servicio al cliente local de John Louis al 1-800-480-6985 para aclarar sus dudas sobre pérdidas, daños, asuntos écnicos y ensamblaje.
Quantity: 6 J-Hook Quantity: 6 Tower Bracket Quantity: 7 Shelf End Quantity: 6 #8 3 in. Quantity: 12 #8 1 in. (J-Hook) Quantity: 4 Cam Bolt Quantity: 14 Shelf mounting L- Clip Quantity: 4 #8 1/2 in. Quantity: 4 Tower Mushroom Cap Quantity: 4 Barrel Bolt Quantity: 24 #4 3/4 in. Quantity: 16 Adjustable Shelf Pin Quantity: 4 Barrel Nut Quantity: 6 Angle Bracket Mushroom Cap Quantity: 56 Wall Anchor Quantity: 64 #8 1 1/2 in. Quantity: 14 #8 3/4 in.
IMPORTANT - Read Before Assembly 12 in. deep Premier Organizer and 16 in. deep Deluxe Organizer use the same assembly instruction process EXCEPT DURING THE J-HOOK PLACEMENT ON THE ANGLE BRACKET. STEP 2 - Marking Measurements On Wall 1. 2. 3. 4. Locate the 3 main shelf height locations for your configuration. Measure up from the floor & mark the 84 in. location. Measure up from the floor & mark the 42 in. location. Measure up from the floor & mark the 72in. location.
2 3 3 4 10 11. 12. 13. 14. 15. 16. 10 Place tower face down (nameplate typically designates tower front) Place top tower bracket between 1 st & 2nd groove. Place middle tower bracket between 8 th & 9th groove. Place bottom tower bracket between last groove & tower bottom. Repeat for opposite side. Secure brackets to tower using #8 3/4 in. screws. 11 12 13 5 14 6 15 16 7. 8. 9. 10. 7 Place tower top (26 1/4in. shelf) into notches at top of tower.
1 2 2 9. 10. 11. 12. 13. Place shelf onto hardware. Place tower onto hardware. Place a shelf end onto the shelf at tower end. Flush tower with top shelf by moving tower left or right. Level shelf front to back & mark shelf end hardware location on tower. 9 10 11 12 3 13 4. 5. 6. 7. 8. 4 6 Position shelf end template onto side wall. Align template line with adjacent wall line. Level template. Mark required Shelf End position for required depth (12in. or 16in. depth).
19 20 21 5. Secure L-clip to wall using #8 1 1/2 in. screws at hole locations (Use wall anchors provided if no stud is present). Repeat for all L-clips at shelf height location. 6. 3 5 4 22 23 5 6 23 7. 8. 9. 10. 11. Position shelf end template onto side wall. Align template line with adjacent wall line. Level template. Mark required Shelf End position for required depth (12in. or 16in. depth). Secure Shelf End using #8 - 1 1/2in. screws (use wall anchor if no stud is present).
12. 13. 14. 15. 16. Position shelf end template onto tower side. Align template line with adjacent wall line. Level template. Mark required Shelf End position for required depth (12in. or 16in. depth). Secure using Shelf End #8 - 3/4in. screws. 12 14 13 15 9 11 10 11 12 13 16 14 16 15 17. Double check required shelf measurement. Cut Shelf if necessary. 18. Place shelf into shelf end hardware & onto L-clip hardware. 19. Secure shelf to hardware using #4 3/4 in.
STEP 6 - Installing Angle Brackets 16 in. Angle Bracket used with 16 in. deep Deluxe Organizer 1. 2. 3. 4. Measure 3 in. back from front of angle bracket & mark location. Place J-hook snug with underside of bracket & align the front edge of the J-hook with the mark. Secure using #8 1 in. screws. Repeat for each angle bracket & J-hook. 4. 5. 6. 7. 8. 9. Insert #8 3 in. screw into angle bracket. Position angle bracket 6 in. or 4 slats in from shelf end (bracket may be positioned in your desired location).
STEP 7 - Installing Garment Bars 1. 2. 3. 2 4. 5. 6. 4 9 10 11 11 Locate the bar dimensions in you configuration guide The double hang garment bars are created by using 2 - 4ft. bars. The long hang garment bar is created by cutting a bar to 21 in. wide (The required distance may vary based on actual closet dimensions) 3 DOUBLE CHECK MEASUREMENTS PRIOR TO CUTTING BARS Measure required dimension, mark & cut bar (if necessary). Repeat for all bars. STEP 8 - Installing Adjustable Shelves 4 1. 2. 3.
Creating Adjustable Shelves Put your excess cuts back into your closet. Any material greater than 24 in. wide can be used as an additional shelf. Cut excess lengths to 24 in. wide to use as tower shelves & place where ever you choose. In an 8 ft. closet configuration your 4 ft. of excess shelving can create 2 additional adjustable shelves. STEP 9 - Final Touches 1. 2. 3. Insert mushroom caps into all angle brackets. Insert mushroom caps into barrel nut holes on tower sides.
11
12
13
14
15
16
17
18
19
20
21
22
23
24
