JOBNAME: CHRY OM (Contenta pu PAGE: 1 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 254B7795 /chry_pdm/chrysler/owners/ctx/sim03.40.00 1 GARAGE DOOR OPENER — EVIC HomeLinkt replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLinkt unit is powered by your vehicles 12 Volt battery. art=033906001.
JOBNAME: CHRY OM (Contenta pu PAGE: 2 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 23A213ED /chry_pdm/chrysler/owners/ctx/sim03.40.00 2 For more efficient programming and accurate transmis- • If you have any problems, or require assistance, please sion of the radio-frequency signal it is recommended that call toll-free 1–800–355–3515 or, on the Internet at a new battery be placed in the hand-held transmitter of www.HomeLink.com for information or assistance.
JOBNAME: CHRY OM (Contenta pu PAGE: 3 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C395F54 /chry_pdm/chrysler/owners/ctx/sim03.40.00 3 art=034000356.tif NO TRANS 3. Simultaneously press and hold both the Homelinkt button you want to program and the hand-held transmitter button. 4. Continue to hold buttons until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED”, then release both buttons. NOTE: • It may take up to 30 seconds or longer in some cased for the channel to train.
JOBNAME: CHRY OM (Contenta pu PAGE: 4 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2125D1AA /chry_pdm/chrysler/owners/ctx/sim03.40.00 4 On some garage door openers/devices there may be a Reprogramming A Single HomeLinkt Button light that blinks when the garage door opener/device is To reprogram a channel that has been previously trained, in the LEARN/TRAIN mode. follow these steps: NOTE: You have 30 seconds in which to initiate the next 1. Turn the ignition switch to the ON/RUN position.
JOBNAME: CHRY OM (Contenta pu PAGE: 5 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1A86A505 /chry_pdm/chrysler/owners/ctx/sim03.40.00 5 2. Place the hand-held transmitter 1 to 3 inches (3 to 5. Press and hold the programmed HomeLinkt button. 8 cm) away from the HomeLinkt button you wish to The EVIC will display “CHANNEL # TRANSMIT”. If the garage door opener/device activates, programming is program. complete. 3.
JOBNAME: CHRY OM (Contenta pu PAGE: 6 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27782D88 /chry_pdm/chrysler/owners/ctx/sim03.40.00 6 Canadian/Gate Operator Programming 3. Simultaneously press and hold both the Homelinkt For programming transmitters in Canada/United States button while you press and release (“cycle”), your handthat require the transmitter signals to “time-out” after held transmitter every two seconds. several seconds of transmission. 4.
JOBNAME: CHRY OM (Contenta pu PAGE: 7 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 279ADD84 /chry_pdm/chrysler/owners/ctx/sim03.40.00 7 Reprogramming A Single HomeLinkt Button Security To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn in your vehicle. follow these steps: To erase the channels press and hold the two outside HomeLinkt buttons (I and III) for up 20 seconds. The 2.
JOBNAME: CHRY OM (Contenta pu PAGE: 8 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1C5C7460 /chry_pdm/chrysler/owners/ctx/sim03.40.00 8 • Did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver.
JOBNAME: CHRY OM (Contenta pu PAGE: 9 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 246DACD9 /chry_pdm/chrysler/owners/ctx/sim03.40.00 9 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
JOBNAME: CHRY OM (Contenta pu PAGE: 10 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 118EAD14 /chry_pdm/chrysler/owners/ctx/sim03.40.00 10 art=034033576.tif NO TRANS HomeLinkt Buttons/Overhead Consoles art=034000355.tif NO TRANS HomeLinkt Buttons/Sunvisor/Headliner NOTE: HomeLinkt is disabled when the Vehicle Security Alarm is active. Before You Begin Programming HomeLinkT Be sure that your vehicle is parked outside of the garage before you begin programming.
JOBNAME: CHRY OM (Contenta pu PAGE: 11 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1EFEE841 /chry_pdm/chrysler/owners/ctx/sim03.40.00 11 Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to Erase all channels before you begin programming. To open and close the door.
JOBNAME: CHRY OM (Contenta pu PAGE: 12 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 24986E04 /chry_pdm/chrysler/owners/ctx/sim03.40.00 12 art=034000356.tif NO TRANS 3. Simultaneously press and hold both the Homelinkt button you want to program and the hand-held transmitter button. 4. Continue to hold both buttons and observe the indicator light. The Homelinkt indicator will flash slowly and then rapidly after Homelinkt has received the frequency signal from the hand-held transmitter.
JOBNAME: CHRY OM (Contenta pu PAGE: 13 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2310549F /chry_pdm/chrysler/owners/ctx/sim03.40.00 13 NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLinkt button until step after the LEARN button has been pressed. the indicator light begins to flash after 20 seconds. Do not release the button. 6. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for two 3.
JOBNAME: CHRY OM (Contenta pu PAGE: 14 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 27953FD0 /chry_pdm/chrysler/owners/ctx/sim03.40.00 14 4. Continue to hold both buttons and observe the indicator light. The Homelinkt indicator will flash slowly and then rapidly after Homelinkt has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.
JOBNAME: CHRY OM (Contenta pu PAGE: 15 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 2239A4BC /chry_pdm/chrysler/owners/ctx/sim03.40.00 15 to pick up the signal during programming. Similar to this 4. Watch for the HomeLinkt indicator to change flash Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up time-out in the same manner. to 30 seconds or longer in rare cases. The garage door may open and close while you are programming.
JOBNAME: CHRY OM (Contenta pu PAGE: 16 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 28DC2BF8 /chry_pdm/chrysler/owners/ctx/sim03.40.00 16 Reprogramming A Single HomeLinkt Button Security To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn in your vehicle. follow these steps: To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all 2.
JOBNAME: CHRY OM (Contenta pu PAGE: 17 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 199A08F0 /chry_pdm/chrysler/owners/ctx/sim03.40.00 17 • Did you unplug the device for programming and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver.
JOBNAME: CHRY OM (Contenta pu PAGE: 18 SESS: 1 OUTPUT: Tue Jan 3 09:31:46 2012 SUM: 1E9E26C3 /chry_pdm/chrysler/owners/ctx/sim03.40.00 18 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.